This tutorial is for Patching db2020 Sony Ericsson phones and all CIDs. So you can now patch your CID53 phone with this guide. You can also use this method to patch CID49, CID51 and CID52 also. Thus you can unlock your phone with unlock patch if you want to do so.
This tutorial is written for new and intermediate users. Advanced users may find this tutorial a bit lengthy, because of the details.
You can find out your phone platform, if its db2020 or not from the SE-LifeStyle Phone Database. Select db2020 in the left column and it will show all db2020. Or else select All in Platform and Click on phone in the Right column, it will show information about your phone platform and also possible CIDs. Its a pretty easy to use tool.
Downloads
Install USB Flash Drivers( You must install usb flash drivers, if not already installed.)
JD Flasher (Updated for AnyCID). (The main tool)
All CIDs Patching Files. AnyCID.ZIP
Video Tutorial, Download.
Read the tutorial, and don’t forget to watch the video to learn ! If you have any problems discuss them at our support forum 🙂 !
Part 1 : Preparations and Basic Setup.
Charge your phone to 100%. At least 95% battery levels are necessary before patching or unlocking or flashing.
Extract the AnyCID.ZIP. In your phone folder, you should find a zip file which contains executor.b !
As an example you can find the following zip file in w580 directory R8BE001_CXC1123362_GENERIC_LA ! This is the ByPass Package for w580 R8BE001 Firwmare.
Here RBBE001 indicates the main firmware version for which the executor.b works. So you better make sure you have a main firmware for which executor.b is available. If there is no ByPass package for your firmware, then you need to read instructions given later at the end.
Download the main firmware .mbn from the Internet. You can easily search in esnips, 4shared or seusers.com for firmwares.
Download Jdflasher, Extract it.
In the directory Far\Plugins\jdflasher\rest you will find mkrest2.exe.
This is the Make Rest Tool. Its used to create the Rest file for your firmware. Rest is short for ReStore.
Copy your main firmware, MBN to Rest Folder and drag and drop the main firmware file (.mbn file) onto mkrest2.exe !
It will create the rest file for your firmware. Keep a note of this file, The Rest file for your main firmware. We need this file later.
Now in jdlfasher\2020_52 folder you will find qamaker.exe, drag and drop your main firmware onto qamaker.exe. You will get the Quick Access Patch for your phone.
We continue with our example phone, Enter AnyCID\w580. Extract the zip file R8BE001_CXC1123362_GENERIC_LA to get tpa\preset\custom\executor.b !
And in the db2020.zip you will find executor.jar and customize_upgrade.xml ! These files are also needed.
Also in the AnyCID folder you will find a file qa2020.xml copy it to jdlfasher\scripts\**here**; Over write the old qa2020.xml with new one from Any CID.
Part 2: Flashing, Copy Breaking files to File System.
We now have to copy the 3 files executor.b, executor.jar, customize_upgrade.xml to tpa\prest\custom in the phone’s file system. This is pretty easy with Jdflasher.
Shutdown phone.
Re-Insert Battery.
Start Far.exe
Press ALT+F1
Select your db2020 in Script option, Select port as DCU-60, And select Maximum Speed 921600.
Also Uncheck the RSA option, this can cause problems.
Now Jump Down Into A Large Rabbit Hole. I mean Click that option ;-).
Jdflasher will initialize and you will will get few options on the left side. Right side is your computer’s file system.
Now Double Click OFS. Jdflasher will start the file system loader and finally you should enter the phone file system.
Enter tpa and then preset and then finally custom folder.
You should now be in tpa\preset\custom\ folder in the phone file system.
Now copy all the the 3 files to this folder, executor.b, executor.jar, customize_upgrade.xml
Copying is easy, on the right side in Far Manger navigate to plugins\jdflasher\AnyCID and then drag and drop the individual files to the Left Side to the phone in tpa\prest\custom\
Before leaving make sure that you have all the 3 files in the phone file system, i.e On the LEFT hand side in tpa\prest\custom\.
Its now time to exit from file system. To Exit you need to go back to the root. You should on double click ” . . ” until you reach root, then click one more, you will get a message in RED. Its the option to shutdown file system loader, so click OK. Basically it says you should re-insert battery.
Disconnect phone and re-insert battery and start phone.
Part 3: Installing Quick Access !
Go to Entertainment and then Games. Run the executor in games. Your phone will turn off.
Now Re-insert Battery. Don’t start the phone.
Start Far Manager.
In The Script option select script as qa2020 ! And Enter the Rabbit hole once more 😉 !
Enter bflash this time.
Naviate to rest folder in jdflasher. Its time to flash the Rest file.
Click on your Rest File.
Press F5 on the keyboard, then click copy, then in 2nd screen click flash. (Flash as a BABE).
Now Navigate to 2020_52 folder, click on your quick access patch, so that its selected.
Hit F5, click copy, hit flash ! It should be flashed as a VKP.
JDflasher will now flash the Quick Access VKP and Install it !
Exit bflash through ” . . ” option.
Unplug phone, re-insert battery. Re-start phone.
Start phone, navigate to games, Delete executor.
Quick Access has now been installed into your phone. Patching the phone now becomes very easy.
Part 4: Patching !
You can now apply any number of patches you want.
Shutdown phone. Re-Insert Battery.
Select qa2020 as script.
Start Jdflasher, jump in rabbit hole.
Enter bflash. Navigate to patch.
Select the patch, press F5 and then click copy and then click flash. Flash as a VKP.
Apply any number of patches in the session.
Exit bflash.
Dis-connect phone, Re-Insert Battery and Start phone.
Repeat only Part 4 whenever you want to apply a patch.
Optional Part 5: Removing a Patch.
Start jdflasher enter via qa2020. Select the patch on your computer which you want to remove. Press F5, Click copy, then in the flash window, select flash as a vkp and Tick the option to remove patch and click flash it. The patch will be removed.
Note: If ByPass Package is not available for the firmware of your choice, Read Carefully.
We have bypass pacakges only for few firmwares. If you don’t find one for your phone firmware, then there is a other way to get around and apply patches. The method is the same, but there are few changes. Here is the Small Tutorial… Its almost the same as above. But you need to re-flash firmwares twice.
1. First Flash your phone with the firmwares for which the bypass package is available. You can download firmwares from topsony or seusers. Flash both the Main and FS. Use db2020 Script, Oflash as told above.
2. Upload the bypass files, executor.b executor.jar and customize_upgrade.xml to FS as told above using JDflasher. Start your phone.
3. Run Executor in Games. Phone will shut down.
4. Connect phone with qa2020.xml and Flash the Main firmware via COPY (F5) of your choice which you wanted. Don’t flash Rest File. Its not needed.
5. Flash Quick Access VKP via COPY(F5).
6. Disconnect. Connect again with db2020 Script OFLASH. Flash the FS of your choice.
7. Connect again with db2020 Script and Enter OFS, upload CDA files. Close. re-insert battery and start phone.
8. Now you can follow Part 4, to apply more patches.
Patches, You can get lots of patches from many forums.
Copy the patches to notepad and then do save as, all files, then save it as patch.vkp. Don’t save as TXT file.
Use Google translator Use it, since some sites are in Russian. But don’t copy from translated russian sites, copy from actual russian site. Not from google translator. mobilefree maintains the most comprehensive database of patches. Most patches are developed by russians.
K530 SW-R8BB001
K550 SW-R8BA024
K610 SW-R1KG001
K770 SW-R8AA018
K790 SW-R1GB001
K790 SW-R6BC002
K790 SW-R1KG001
K790 SW-R1JC002
K800 SW-R1KG001
K800 SW-R8BA024
K810 SW-R6BC002
W580 SW-R6BC002
W580 SW-R8BA024
W610 SW-R6BC002
W610 SW-R8BA024
W660 SW-R8BB001
W710 SW-R1GB001
W710 SW-R1JC002
W850 SW-R1JG001
W850 SW-R1KG001
W880 SW-R8BA024
Z610 SW-R6DA001
Z610 SW-R1ED001
Notes–
1. To unlock phone apply the unlock patch. Unlock patch can be generated using SIMOX tool with your main firmware mbn file.
2. If you re-flash main firmware, all patches will be erased, you will have to re flash Quick Access vkp again and then flash all patches again.
3. You may want to read the Jdflasher tutorial for help on flashing and customization.
4. You can’t apply patch that is not for your phone. You should also ensure that the patch is for your firmware, else phone will crash.
5. Some patches may de-stabilize your phone, be careful.
I have provided the video tutorial, so am not adding pictures. That’s cool enough.
Regards,
Akshay.
Thanks. There’s also den_po’s version at SE-NSE…
i’ve got small problem my phone is k550@w610 cid53 and when i select qa2020 and start it’s popup a error “openplugin <connecttophone<getcid>>
ok problem solved, solution copy qa2020.xml from anycid to \Far\Plugins\jdflasher\scripts
but i still cant apply QA because of SetDirectory<setdir<setmode<doscript<run<gethello<IOusb:getblock>>>>
any ideas??
hey i got a problem…
after do steps above, my phone wont turn on!
it’s infraport doesn’t blink and screen doesn’t blink…
what’s wrong?
i will try reflash…
Sorry man, fixed, there were 2 errors. OFS and qa2020 copy, i have fixed them.
Thank you.
ok this issue is due to Badly Installed USB Drivers.
after reflash, my phone went fine…
but why does it won’t turn on???
i’m confused in this step:
Navigate to rest folder in jdflasher. Its time to flash the Rest file.
Click on your Rest File.
Press F5 ok keyboard and then click copy, then in 2nd screen click flash.
flash as what>
babe, raw or vkp?
i choose babe…
this is still oflash:
“Enter bflash this time. Yes Its BFLASH now. Not oflash as in Part 2.”
hahaha!
AKSHAYY!!!
2 TIMES I’VE TRIED, AND 2 TIMES IT WONT TURN ON!!!
SOLUTION PLEASE!
NOW I’M REFLASHING MY PHONE! AGAIN!
yes i too have same problem .. my fone(k800i cid 53red) won’t start up after flashin + qap 🙁 🙁 🙁
i tried many tymz now .. but it wont start …
den i reflashed in db2020 mode & it started but no patches applied
tell me where i went wrong ??????
plz some1 help me ..
jordyzzz, this is the den_po’s original version
http://forums.se-nse.net/index.php?showtopic=37156
ok, i will talk to you. let me see what’s wrong, and what’s not working.
you should follow things carefully.
Yes you should flash the Rest as A BABE.
@jordyzzz
well bro do one thing…post the whole procedure here!what u did!
ill try to figure out the error if u did!
ok, wait!
Allright akshay, this is my procedure…
1. Create qa patch and rest for k800_r8bf003_main_generic_WI_red53
Problem in this section:
1. Mkrest2 didn’t create any rest file, so I downloaded them from 4 shared (the name is just mkrest). Is this a problem?
2. Qamaker makes quick access of my main, but the name of qa patch is:
“xyyy_r8bf003_main_generic_WI_red53.vkp”
Xyyy should be k800 right? What’s wrong?
2. Change my qa2020.xml
3. Upload customization_upgrade.xml, executor.b and executor.jar into tpa/preset/custom
4. Run executor and release battery
5. jdflasher, qa2020, bflash…
6. flash REST as babe
7. Flash xyyy_r8bf003_main_generic_WI_red53.vkp as vkp patch
The log:
When putting customize upgrade
create session object
used script: db2020.xml
turn off the phone, hold “c” button and plug usb cable
found EPIUSB2
connecting…
got response
protocol: 0301 baseband: 9900
cid detect
<- cid=53 color=red platform=db2020
qhldr: 070703 1229 DB2020_SEMC_RECOVERY_P3N.2020_1_BLUE
<- hello: 070703 1229 NPA4_CXC1329130_DB2020_SEMC_RECOVERY_P3N
cmd3c: 070904 1245 DB2020_CSLOADER_R3A013.2020_53_RED
/tpa/preset/custom/customize_upgrade.xml (531 bytes)
-> /tpa/preset/custom/executor.b (3692 bytes)
-> /tpa/preset/custom/executor.jar (43534 bytes)
Ls cd .. ls cd .. ls cd ..
When flash rest and qa:
create session object
used script: qa2020.xml
turn off the phone, hold “c” button and plug usb cable
found EPIUSB2
connecting…
got response
protocol: 0301 baseband: 9900
cid detect
<- cid=53 color=red platform=db2020
qhtry: 2020_prologue
run flashed loader
<- hello: DB2020_PRELOADER_FOR_SETOOL2
let’s say thanks to mr laser 😉
cmd3c: 2020_f_R2A005
<- hello: 061201 1314 HA…_DB2020_FLASHLOADER_R2A005, den_po
activateloader
flashID: 897E (Manufacturer: Intel)
<- OTP: status 0 locked 1 cid 51 cert 1 IMEI 35427102xxxxxx
flashing babe: K800_R8BF003_MAIN_GENERIC_WI_RED53.mbn.rest.mbn
flashing 1 blocks
1 blocks flashed ok
reading 8 blocks
making a patched babe
flashing babe: quick_access_XYYY_R8BF003.vkp
flashing 8 blocks
8 blocks flashed ok
8. try to turn on phone, phone won’t start, no red light blinking and no screen blinking…
i’m sorry, BHUVAN…
or akshay too…
Am on it !
it doesen’t work for cid 53,it stop’s on step 4 , the executor in the games dir won’t start:| ,i will look for updates…
no ! you made some mistakes then
when you start executor the phone should shutdown.
So can we use elf packs with there tech.is there any method to install elf pack in cid53 W580
yes now you can install elves into the phones. you need to apply the elf pack patch and elf libraries.
Excellent.
I’ll have a couple of strong esspressos and try to follow this guide…
*I’m going in, keep me covered…*
I have verified this method, it works, i am now going to post video tutorial in few hours. have fun !
is there a tutorial for db2010/db2012 phones like w200?
Video tutorial added. Now don’t ask me if this method works.
Cant seem to find phone.
Drivers wont stay installed.
Where phone is connected (E:) get message:
cannot read the disk in drive E.
Hmmm?
What am I doing wrong?
oh god many many errors. install drivers using ggsetup its the best and easy way.
go to start and sony ericsson and rest ports if not workig.
what E: ?? what phone do you have ??
k770i – R8BC004
The ‘E’ refers to where the computer assigns the usb cable.
I’ve installed with ggsetup but computer still wont access the phone.
well for all dos who have error dat fone won’t start is dat u have 2 flash rest file first & den main firmware ..
for further clarification ..
http://www.esato.com/board/viewtopic.php?topic=179961&start=120
Ja haaa…
The reset helped, as did some more coffee.
Now I’m progressing…
Thanks…
Hmmm.
Now it wont make a rest file.
i have a question. i drop the main firmware into mkrest2 but the rest file didn’t show:D i should download another mkrest2.exe file?
making rest file is so easy. download correct main firmware and then try. just google search for main firmware you will get it 😉
no download other main file. working one with correct header.
its not necessary to flash rest file. I am certain.
when i enter bflash it gives me error……………..
i have coied the qa 2020 script from any cid folder to plugins\jdflasher\scripts but still no success………….
i tried the whole procedure again and again for abt 20 times………………
earlier i used to patch my w580i cid 52 but now cid 53 is giving me errors……………..
i also unchecked the rsa option…………….
i am even unable to flash my fs with the help of jdflasher…………………..
Akshayy,,,
I have a problem.my phone is k550,i want to flash it to w610,but i can’t find the file executor.b for my fone (my software version:w610_R6BC002_CXC1250670_GENERIC_CHINA_LI) in AnyCID.zip.
There’s only for R88A024_CXC1250747_GENERIC_NA.
Is that possible to flash using that file?if not,could u give me the link where i can download AnyCID.zip that contain my fone version?
Thanks,,
sorry,my phone version is k550_R6BC002_CXC1250670_CHINA_LI not w610_R6BC002_CXC1250670_CHINA_LI
Akshay,,
I can’t found the executor.b for w610_R6BC002_CXC1250670_CHINA_LI in AnyCID.zip that u give.
Could u give me another AnyCID that support my phone?my phone is k550,CID53,software version:R6BC002_CXC1250670_CHINA_LI.
Or i can use the other software??
pliz help me,,
Thanks,,
Hi there,,, i stuck on the rest file generation.. i Drag the MAIN firmaware on the mkrest2, a black window opens for a moment and then nothing happends… I downloaded 2-3 mains from differnet sites but again nothing happens.. Any idea? can any1 give me a link to downlaod the rest file for W660_R8BB001_MAIN_GENERIC_FY_RED53 ?
Thx in Advantage
ok, few people are having issues with w580. don’t know why.
yes, i have a solution for that. I will post it.. check back.
download w610 R8BA024 CID 53 Main and flash it. Then download w610 R6BC002 FS and flash it. Flash the correct CDA.
Then use w610 R8BA024 break files, executor.b etc. After flashing rest files flash w610 RBC002 main and then continue with Quick Access. Then rest tutorial is same.
wow!
one more w580 user having the same problem which i have!!!
now number reaches to 4!!!lol
dont know but this is the only one problem in the world of flashing i saw so far with no fix yet!
bhuvan i’ve got the same problem but w610 and few other users from polish forum so there more of us 🙂 but i hope that someone find solution for this
Using z710 firmware. Can’t make a rest file.
Flashing R6BC002 FS using what??bflash,oflash or ofs?
@Bart3z
we can only wait for den_po now
let him read all of this problem at se-nse as he his there!
as sson as there will be cure out ill make a new topic here!
@LOKI
what are you facing??
which os?
@Fer
bflash
hi there again. i made all that processes but still won’t turn off after i click executor on games dir. is another file’s like executor.b/executor.jar/customize.xml for k550i r8ba024 cid 53 db2020 because i think that is the problem. tx
does anyone had w850 main and fs firmware R1KG001 cid 53??
I had alot of problems using any cid but cracked it finally!!! I followed the vid tutorial EXACTLY but i couldnt make a rest file using mkrest so i used the one that comes with se tools lite and bingo!!
@romario
its because u must have installed the executor file!
do one thing
re flash your fs!
now upload the three files to ur fs [db2020 folder one and your mobile\firmware model one]to tpa\preset\custom!
and then u will see a executor file in games folder run it and your will turn off!
@paoli
w580 dont have any such firmware!
@Deejay1210
you must be using xp as os!
there you have to get it done by manually getting on cmd
hey guys with ur support i have flashed my w580i and patched so much tht two joint butons above walkman button stopped working, so i get repaired from serive center as it was under warranty!
but now they flashed me r8be001 cid53 from r6b cid52.
i wanna do some patching and modification is it a rite time or should i w8 for sometime and is it safe to do it???
akshayy and all thanks 4 ur support.
@EverWin
[:o] not at all possible!
patching is just a part of few tweaks in software of your phone!
aint got any link with keys!
and you can do patching whenever you want!but in limit…if number goes damn high and your device is not able to manage it then your phone will hang or restart!
and i too got w580 and had the same problem!right now having in the right navigation key!
hmm… thanks 4 reply so i can unlock my phone and add some of flash themes and can use few patch can i??? can i use cid52 patches 4 my phone
do anyone had fs and main for w850i firmware cid53 color red?
Uhhhmmmm @ bhuvan, it’s not w580 it’s w850i… my current firmware is RIKG001 cid 53 (because of SEUS update), i want to try patching it, but i don’t have cid 53 fs and main file (.fbn and .mbn)…
Is it okay for me to use cid 52 firmware to flash the phone (sounds scary)
Oooppp sorry it’s not RIKG001 it’s R1KG001 mistype “1” by “I” there…
Hi there,
I have followed your tutorial carefully, cross-referencing with other sites just to make sure.
But I run into a problem after I flashed my k530@w660 with the R8BB main firmware as stated after flashing with R8BE rest file.
The problem is that I can’t enter Bflash. As soon as I enter it, the phone turns on and I get an error in FAR manager.
A screenshot of the screen can be found over here: http://img132.imageshack.us/img132/8730/erroroi5.png
I have already updated JDFlasher to v Jun 30 2008 and I am still getting the same problem.
Hopefully you have a remedy for my problem 🙂
Awaiting your reply, K12
@EverWin
ya!sure no risk
and payches are firmware dependent not cid dependent!
so choose ones acc to your firmware
paoli
ohhk my mistake!
well go for topse…there you will get it easily
user name:vishnuhost
pass: danger
@ K12
well bro i am too having cid:53 w580!
though you may find me as an expertise but i am too facing the same error!
we guyz are trying our level best to cure out of this problem but no luck yet!
so if there will be any chances then we will definately post a new topic here regarding this error as many people are getting the same thing!
@bhuvan thanks for referring to topse.ru, but i can’t use the username and password, so i try to register… It’s quite hard to register since i’m having problem with the language :p So i use babelfish to translate it for me. :p
After registering, i go to http://www.topse.ru/firmwares and choose w850, but it seems they don’t have the firmware for cid 53 too. They only had cid 52. I’ve searched through googling for 1 week, 4shared, rapid, mega and anykind of file server, and still haven’t found it… I guess, there’s nothing that i can do right now.
Hey, bhuvan, where does these firmwares coming from?? I mean who is the person that distributed it?? Is there any way for me to take out (or copy) the firmware directly from my phone?? (the .fbn and .mbn files), i’ve been googling and haven’t found the answer to these questions.
Anyway, thanks a lot for giving me a help bhuvan..
OMG, Bhuvan, i look at w830 which has the same model as w850, and found out that w830 has their cid 53 firmware in topse.ru
It’s R1KG001 cid 53, the same exact that i’ve been searching too.
I wonder if i can use it since both w850 and w830 has same model?
I’ll wait for your answer, since i’m afraid that i’ll lose some feature in w850 if i flash it with w830 firmware 🙁
Hahahaha never mind what i’ve said bhuvan, i’m googling about flashing w850 using w830 firmware, and it seems even both model has the same interface, the filesystem is of totally different and there’s been a lot of case where people flash w850 using w830 firmware and they totally brick the phone :p
Back to patiently-waiting-for-w850-cid-53-firmware mode :p
@paoli
the main difference between both of them is w850 is 3g phone and w830 not!
thats the only difference!! so you can use w830 firmware on w850 or w850 firmware on w830!and thats y topse people have uploaded only one model’s firmware as the other one will too b same!
so without worries go one and get it done!
@bhuvan
thanks to you,
i ve successfully unlocked my w580i (r8be001 (cid53))
now am gonna try some other patches and let u know
u rok
@EverWin.
That’s cool.. Finally a reader has got it.
Tutorial updated, now its even better.
Hi. I can’t seem to find the executor on my phone even though I’ve copied the 3 files mentioned above. What’s the likely problem? Thanks!
sorry…missed out customize_upgrade.xml …doh! please disregard above…thanks.
After patching my K790i CID53 R8BF003.., I have a problem my phone automatically restart anytime…, How to fix this problem without using MAIN.., The patches are work good only problem is just phone is restart automatically….,
chintanbtech
its coz you applied a wrong patch or a bad patch, remove it or reflash main
For Those who are getting “Time Exceed” Error.
I used to get the same error, but i finally managed to successfully patch my W610 R6BC002.
I did 2 things differently
1–> install ggsetup (Flash Drivers for SE)
2–> when i run executor , the phone used to restart.
But this time i removed the battery before it would restart.
after that i didn’t get the “Time Exceed” Error, i was able to patch my phone successfully.
May be this would help u guys as well.
hmm thanks, also if you had R6 FS and Main it would haven’t be there at all. i guess so. because even i researched the same and many settings.
Thanks! akshay. That flash tutorial was impressive.
@bhuvan, no bhuvan, w850 (using 3g, no EDGE), w830 (using EDGE, no 3g)… well at least that what i read from guys in se-nse…
And some guys in se-nse has given warning regarding cross flashing between these two model…
Cause it will certainly damaged the signal function and the phone will receive no signal at all if it’s being cross flashed… 🙁
akshay , if i have r6 system in my w610 , can i use the elves ??
yes you can.
thanks akshay !!
Hi all… I followed the tutorial, and everything is fine until I copied the 3 files into tpa\prest\custom after this i removed my battery and restart my phone but when i try to run the executor app in games it show “Operation failed”.. I haven’t got a clue what have i done wrong.. I have tried so many times and same result… btw, my phone is DIC53 and locked to vodafone, does it affect anything??? Pls email me if u know the solution
eddietan83″googlemail.com
many many thanks….!!!!
hey ed. did you delete customize.xml and preloaded_config.xml files from tpa\preset\custom ??
try to put them back. or else re-flash your file system and and upload cda files. check out the jdflasher flashing and cusotmization tutorial.
don’t worry nothing serious, it can be fixed easily ..
hello, im newbies dont know how to patch my k810i.
this my k810i info
05:57:27| Baseband ID: 9900
05:57:27| Protocol Version: 3.1
05:57:27| Warning: IMEI name does not match GDFS name (IMEI:NULL GDFS:K810)
05:57:27| …using GDFS name
05:57:27|
05:57:27| Profiling SEMC phone…
05:57:27| Platform: DB2020
05:57:27| OTP CID: 51
05:57:27| EROM CID: 53
05:57:27| EROM Color: Red
05:57:27| IMEI: 35315302xxxxxx
05:57:27| Phone ID: K810
05:57:27| Region: APAC
05:57:27| CDA: CDA102568/1 R2A
05:57:27| Firmware Version: R8BA024
05:57:27| EROM: R3A022
05:57:27| Ready for operation!
R8BA024 -prgCXC1250904_CHINA_SM
i try the tutorial JDflasher but stuck in first step to mkrest2.exe please help me!! tolong..
hmm, i can’t really help then. try making the rest file via command line
or download ready made rest file from internet.
Perfect thanks for this now i modified my sister’s k770 R8BA024 phone yey! more power akshay
I’m looking for k610i Hutchison TH R1JE001 firmware.
prgCXC1250539
Anyone have?
hy again. another problem i found:D i reflashed my k550i Red53R8ba024 with K550_R8BA024_FS_CENT_EUROPE_RED53.fbn and after reflashing my display show:Configuration error.Please contact your operator or service centre.” please tell me what to do to return to old setings.Tx
also when i go to OFS i get this message
[URL=http://img529.imageshack.us/my.php?image=prblka6.jpg][IMG]http://img529.imageshack.us/img529/9132/prblka6.th.jpg[/IMG][/URL]
also when i try to run ofs i get this message :
http://img529.imageshack.us/my.php?image=prblka6.jpg
The executerb for my k610i isn’t in anycid, do I pick one of the ones thats there?
for k610, use the firwmare for which the executor.b is available. you can get it from topsony or seusers.
while using OFS, use script as db2020 and enter. try to re-flash man and fs.. then enter OFS.
to clear config error you need to flash those 2 files, customixation and preloaded_config.
strange that oflash works but not ofs.
romario, probably you should download latest jdflasher.
it doesnt work . i flashed thru Oflash ->Main with K550_R8BA024_MAIN_GENERIC_LI_RED53.mbn and Fs with K550_R8BA024_FS_CENT_EUROPE_RED53.fbn
@romario
the error is coming because you havent uploaded the cda pack
get it one of your region
they contain few netwrk tweaks…
google it
like cda [fone model] region
Hello,
thr’s nothing tht is not worked yet everthings is working fine all patches are working even elfpacks working fine not a single reboot on using desktop dock, sound-slider, logo-changer, i ve tested everythings working fine except i cant able to flash FS on my phone
any comment!
Hey people! I’m not sure how these things go, but is there a chance someone will release the cid53 firmware for SE W850i? It’s an old model, so I’m wondering if it’s worth waiting for a firwmare, or should I just toss it into the trash can and start looking for a new phone? 😀 🙁
how to backup and restore gdfs for cid 53 ???
what error do you get when you flash the FS ??
EverWin
what’s the error you get ?
Bollocks.
“You do not have permission to access this entry.”
Said seusers and topsony gave me the runaround too.
I’m trying to dl the main firmware for my k610i phone in order to flash it with FAR manager.
The two instances in Anycid are:
R8BE001_CXC1250374_GENERIC_TH
R1KG001_CXC1250374_GENERIC_TH
Both of which I am not allowed to download, I’m running in ever decreasing circles…
Can anyone help?
I’m looking for k610i Hutchison TH R1JE001 firmware.
prgCXC1250539
Anyone have?
tutorial abt executable.b
Tell me where i can download them
Jan 29 at 20:23
I’m looking for k610i Hutchison TH R1JE001 firmware
CDA:CDA102497/48 R17A
@Andy, topsony or seusers do allow, i don’t know why what’s the problem. can you try again.
also you usually get files in rapidshare or 4shared or enisps or some free hosting site. you can try google search the exact name. you will get definitely.
imanuel. you can get firmwares from topsony or seusers websites. 🙂
What is the difference between a rest file and a MAIN file (.mbn)??
@ hellboy
main directly works in flashing
hi akshay….
yar i cant able to make rest files from my main file…when i hold my main file and drag into mkrest2 then nothing would happen….and after done all the neccessary steps for patching cid-53 when i select qa2020 then suddenly i got an error message plz help me out…
@akif
u must be using xp
go for manual cmd commands
where to find W660 R8BE001 patches??
plase help me akshayy
@anshgmbtech
google it…
join our forum…get a topic there…and a lot of sutff will be provided
topse too
bhuvan
i cant find it for W660 R8BE001 ca u help me by giving some links please Bhuvan.
Bhuvan r u from India,which state?
@ anshgmbtech
what u want???
u mean…that main and fs???
go for topse…
the best place for downloads!
and yea…i am an indian….for rajasthan
u??
can the patches of cid 52 applied on cid 53
@@ani
patches are firmware dependent not erom
How do I do this with my w810 CID50 db2010? :O
I feel pretty lost…
@thatinsaneguy
common:
1) use mkrest to make rest for your fw
2) extract contents of {yourplatform}.zip and {yourphone}/{firmware}.zip to your phone
3) turn your phone on and run games/executor
4) reinsert battery
db201x:
5) start jdflasher, select right script (don’t forget to edit cid num value in it), uncheck “rsa” box, connect, enter to bflash
6) flash rest
7) do whatever you want
continue from the step 3 further
bfs doesn’t work
done it:P finally, now i’m looking for some louder sound drivers(patches) . can i flash a driver zapf for k550 with bflash?:|
@ romario
huh??????????
patches can never configure sound drivers!
what all you need to do is just find out a good acoustics pack..upload it to
ifs\settings\acoustics
and for db2020 i would recommend w880 extreme
best and well balanced
i am too using hat one only!
get it from filebase
many more are there
i have k550i cid53 . does i use above tutorial for flashing k550 to w610 as same in video
is it possible to flas k550i cid53 to w610i cid52
@tahir
no erom cant be downgraded
secondly…yea…same method but use you phone’s files
sry i didn’t replied ur question early, i was quite busy—here’s wht i get when i try to flash FS
PutFiles(putfile(putfile_flash(flashbabe(header(send header error 15)))))
my firmware version is W580_R8BE001_MAIN_GENERIC_LA_RED53
and FS version
W580_R8BE001_FS_S_ASIA_LEVAN_RED53
am using Far—>db2020–>OFlash
Thank You
Hi, I have crossflashed my K530i CID 53 to w660i. I have some custom acoustics for w660i, can i update these acoustics on my K530i>>w660i using JDFlasher+FAR??
Please help!
Thanks.
@EverWin
what are you doing????????/
i mean…i rply so many posts everyday…so i forget the old ones
@ Manmeet
yea
why not?
@ Bhuvan
Thanks a lot 🙂
@manmeet
anytime
after copy executor and all stuff in my k810i, restart the phone, but when i go to games, and try to start executor, says “Operation failed” and the phone don’t turn off…please anyone can help?
bogdMan
strange
which all files did u copied to your fs
??
executor.b
executor.jar
prgCXC1250811_GENERIC_SM_R8BA024.rest
quick_access_K810_R8BA024.vkp
customize_upgrade.xml
everything worked just fine, but i cant open executor…operation failed…
in anycid, for k810 are 2 files:
R1KG001_CXC1250811_GENERIC_SM
R8BF003_CXC1250811_GENERIC_SM
who both contained executor…I put in my phone executor from R8BF003_CXC1250811_GENERIC_SM
I should try with another? please help, the phone is for my nephew as a gift…
please bhuvan, give me a clue…something…
bogdMan
look
first of all flash your phone to supported firmware
which u gt???
flash to one which are provided in anycid folder…in k810
this
R1KG001_CXC1250811_GENERIC_SM
R8BF003_CXC1250811_GENERIC_SM
any one of them
then try it
uffff I have only this firmware: K810_R8BA024_MAIN_GENERIC_SM_RED52 which is in my phone too…I cant find R8BF003_CXC1250811_GENERIC_SM firmware for k810i, and I need a tutorial to flash my phone with it…(if i find it)…I use windows mobile and it’s a lot easiear to apply anything…
I dont want to unlock the phone, I only want to apply patches
@bogdMan
to apply patches u need compatible firmware
u need to flash to any one of them,!
tutorial is there
look in our site
jd flasher flashing
i have this problem :
i drag n drop the .fbn firmware to mkrest2.exe but no file generates,and qamaker drag and drop no file come up:( just a error
with “cmd” it says that can not recognize it or something similar 😕
Tryied also with Vista 32bit,and qamaker says :”file saved.you can use XS++to flash it”
but nothing comes up 🙁
When im trying to start executor in games i get an error message “operation failed” WTF is wrong??
how come may jdflasher only have ofs and oflash?i don’t have bflash
@hamstern
u must have uploaded the whole .zip package!
@wufei
completed the new qa script thing?
Thanks 4 u.i understood it.1)please tell me have any way to read m3g(3d file) file in my K530i or w660.some thing like a patch.
2)please give a other download link for Qamaker.exe without on 4shared.because im download them using my K530i.???
bhuvan thanks very much, finnaly it works…
@Lahiru
m3g file??there is no such file!
qamaker…well…google it
if u r not having net on your pc then connect using your mobile
install pc suite
@bogdMan
any time
@bhuvan
No i dident do that, just uploaded
executor.b
executor.jar and customize_upgrade.xml
@bhuvan
This is my phone
Profiling SEMC phone…
Platform: DB2020
OTP CID: 51
EROM CID: 53
EROM Color: Red
Phone ID: K770
CDA: 1202-4371 R5A
Firmware Version: R8BC004
EROM: R3A022
akshay, if i want to flash my w610 back to R6, what quick access VKP do i need to use?? is it R6 or R8 ?
i cant able to flash FS on my phone
w580 cid53 when i try show me error
PutFiles(putfile(putfile_flash(flashbabe(header(send header error 15)))))
hamstern
of right firmware version????????/
@hamstern
well do one thing
take a backup of your phone
re flash your fs
now upload custpack…acc to your region
turn on the phone
now shut it down and upload anycid files
@sanzou
reflash main and fs to that firmware
@EverWin
get the latest jd flasher from our filebase!
Hi, I have cross flashed my k530i>>w660i, just wanted to know if i can change the camera button to the Play/Pause button (which is missing in K530i). Is there any patch available for doing so? Please help!
@Manmeet
afaik its no there
for that…join our forum
and request there
@bhuvan, if i flash to R6, then i need to flash Firmware R6’s quick access VKP patch ?
how do u guys backup ur cid53’s gdfs ?? do i need to backup gdfs for my w610 cid53 R6 firmware?
@ sanzou
cid:53’s gdfs cant be backed up!
so…forget about gdfs
r6 firmwares backup..look at fs exacting tut
vkp patch can be made with your firmware itself….
main
cant make a backup dont know why.
looked at some tutorials but still cant make it work
Cant find i custpack for my R8B 🙁
help plz
is it ok for me not to backup gdfs and follow the unavailable bypass package guide??? or do i need to wait for XS++ 3.2 ??
@sanzou
vkp can be generated with main
so get it
no way of taking cid:53 phone’s backup!
@ hamstern
for custpack go for se nse
or topsony!
or google it like
cda pack [model no] region
backup of what
?
@sanzou
if u use linux then u can use phonexs
if no then no way!
u can follow the way it is here
till now no one faced problem regarding gdfs yet in this procedure!
oh…but theres no guarantee that i will not facing any problem rite?
what can cause gdfs error ?
@sanzou
till now no one faced in cid:53 phones!
so keep moving!
go the way it is written here
okay…i’ll try it tomorrow… =)
thanks akshay for the guide n bhuvan for helping me… =) i have successfully patch my w610 main R6 n FS R8 🙂
@ sanzou
nice
akshay, for the unavailable bypas package tutorial….you should upload Custpack after you flash the firmware n fs in the 1st step….people will get configuration error… 😉
@ sanzou
for that ull have to join our forum
as this is special for only tuts
so…
hi i see your tutorial film and do exactly what you do.but occur two important problam.first:i am sure i have correct main but when i drag it on mkrest2(without .exe)dont generate rest file how ever i can make quick access by draging main on the qamker.second:when i do part 2 and select executor in the game part of my phone and torn off then select qa 2020 in the jd flasher show me eroor:open plugin/connestto phone/get cid/cant fine device info in xml[5red]>>>.help me plz
@rohani1366
which phone are u having?
for that mkrest thing
are u having admin rights????and try on other drive
Hey :O
The rest file doesnt show when i drap the main onto the mkrest2. Just need to clarify that i am using the correct file.
I have a W580i CID53 and using :
W580_R8BE001_MAIN_GENERIC_LA_RED53.mbn
Also, while im here :P, would i be correct in using :
W580_R8BE001_FS_CENT_EUROPE_RED53.fbn
I downloaded these a while back, so..umm..let me know 😀
@ sethzen
files are correct
r u having admin rights??????
try on other dirve
I do have admin and i tryed another, but it still doesnt work.
What happens is that the command prompt pops up says the mkrest2 by den_po or something, flashes something else up but then closes too soon before i can get a good look at what pops up.
I can create the qa thing though (VKP file).
nevermind, it saved the file to a random place on my hardrive which i found by searching for the file 😀 thanks anyway
@sethzen
ohk
where was it saved?
and u can still solve it by working on cmd manually!
Hi all… I have recently cross flashed my K530i@w660i CID 53. I want to apply some patches to the phone and I followed this tutorial and copied the 3 files into tpa\prest\custom after this i removed my battery and restarted my phone but when i try to run the executor.jar from the games folder, it shows “Operation failed”.. I am unable to proceed after this!
Manmeet
thats not possible
u are committing some mistake
check out that have u uploaded right files
still doesnot works then reflash and then try
Manmeet,
Check again if you are uploading the files for W660 and not K530.
If the files are for W660, then see if the firmware you have in your phone is either R6AD001 or R8BE001. Upload correct files 😉
@hellboy/bhuvan
I have uploaded the files for W660i only and the firmware i hv is R8BB001.
I have also applied custom acoustics and they are working fine.
Just wanted to clarify, after crossflashing we need to copy the cust pack, i only copied two files from the folder i.e. “Customize.xml” and “preloaded_config.xml”.
Have i missed out anything here? or do i reflash the fone again?
@Manmeet
thats nthng wrong
well…now if still it si not working then re flash your phne…and now try
Hi! thank you! i finally mannaged to mod my k550i CID 53 DB 2020, after reading your tutorials, the video was especially great! Thank you Akshay!
Ah, I upload the files, and try to run executor on the phone, with no results. I just get the error “Operation failed”. Why? This is with CID53
I am using the below MAIN and FS but I have some doubts with the bypass package method.
Current:
K800_R8BF003_MAIN_CHINA_WI_RED53
K800_R8BF003_FS_APAC_RED53
1. Flash my K800i with K800_R8BF003_MAIN_GENERIC_WI_RED53 and
K800_R8BF003_FS_APAC_RED53.
2. Upload the bypass files, executor.b executor.jar and customize_upgrade.xml using JDflasher. Start the phone.
3. Run Executor in Games. Phone will shut down.
4. Connect phone with qa2020.xml and flash K800_R8BF003_MAIN_CHINA_WI_RED53.
5. Flash Quick Access VKP via COPY(F5).
6. Disconnect. Connect again with db2020 Script OFLASH. Flash K800_R8BF003_FS_APAC_RED53.
7. Connect again with db2020 Script and Enter OFS, upload CDA files. Close. re-insert battery and start phone.
8. Follow Part 4, to apply more patches.
Please correct me if my steps are wrong. I need to read and write Chinese on my K800i so I prefer to use K800_R8BF003_MAIN_CHINA_WI_RED53 and K800_R8BF003_FS_APAC_RED53.
@John
heard this many a times earlier too!
well…take backup of ur phone..
reflash…upload cda
now start the phone…
now turn it off…now upload anycid files
and now try
@SilverLeos
afetr the first step upload right cda pack to your phone
start it
and now continue with 2nd step
look there are a lot many mistaked u are making
better look at whole the guide again
from 4th step onwards
and yea
download the video tutorial also
that will help u a lot!
Ok, I will read the whole guide again and download the video tutorial. Btw, can I still view and type chinese on my K800i after flashing successfully?
@SilverLeos
Flash with the chinese main if you want to type chinese.
@ SilverLeos
yea
hellboy is right
@Bhuvan
I have reflashed my fone but still i am not able to patch it!
Do u think i shd use D-Ultimate unlocker and downgrade to CID 52. I think CID 53 has hell lot of problem for patching.
Please suggest.
@ Manmeeti agree…cid:53 got a lot of problem in patching
D-Ultimate unlocker
whats that?
well there is no way of downgrading erom yet for free
!
@bhuvan,
Go to Top Sony to read about D-Ultimate unlocker 🙂
@Manmeet
No need, follow the tutorials carefully n you won’t have any problem patching….
@Bhuvan
No its not for free, i will be paying 10 euros for the app. But i think its worth it!
@Bhuvan – Here’s a link to that sw:
http://www.topsony.com/forum/cmps_index.php?page=buy_log_ultimate_unlocker
@ Manmeet
what all can u do in that app?
and if u can do that for free then why pay so much amount??
instead…give me a dashing party!
lol
@Hellboy
I have cross flashed my K530i@w660i twice, and followed the CID 53 patching tutorial step by step, but i still get “Operation failed” when i run the executor.jar from the games folder!
🙁
hii, i have a k550 cid53, when i run the executor in games it says OPERATION FAILED, what i do?Plz help!!!
@Alexe_01
reflash your phone…upload cda files…start your phone
now turn off….and now upload anycid files
now give a try
remmber firmware compatibility
Hey i have a s500i CID53 and after step two, my phone is still locked…it says:
“please insert correct sim”
anyone help?
o btw, i couldnt make a rest file after dragging it in…i dont know why…think that could be the reason?
also just noting in case its important, my executor.b was in like purple when i was in the far.exe program…
@Sammy
strange!
check the extionsion of executor…purple color shows that file is in rar format
for mkrest…try manula cmd commands
@bhuvan
wait, so it cant be in a rar format when you drag it? then wat format should it be in?
@Sammy
it should have extension .b
extract the rar file
am a newer in patchng…
my phone is k550i, cid 53…..
i have flashed it to w610i (W610_R6BC002_MAIN_GENERIC_NA_RED53)……
if am applying patches den which patch files should i use? w610 or k550? pls rply……….
i dont get reset file…… am usng d firmware
W610_R6BC002_MAIN_GENERIC_NA_RED53.mbn
@afsal
patches are firmware dependnt…so use w610 one
if u are using xp then ull have to use manual cmd commands to get rest file
this tutorial is very confusing to me. maybe only geeks can only immediately understand this tutorial. i really want to patch my K800 cid53 phone so badly especially the awesome vista menu pack and i want to change the annoying almost whispering sound of my phone. sob
amigo2008
this is the simplest!
every one used to say that!
well u are new i guess..in other words…noob!
want some live help then jump onto our forum
i have a k800 and when i copy the three files to oflash and turn on my phone its says incorrect sim card so how am i to access the games folder?
best
ull have to use the old one sim..which was supplied with it..
but thats from another region……i cant use it where im from
@bhuvan
the first thing that confuses me in this tutorial is this: at the beginning of video tutorial, there are three folders: far, firmwares and patches. i want to know where can i get/download the appropriate firmware with mbn file for my K800 cid53 R8BF003. could you please give me a link where can get this file. i would like to ask also if the stuffs in mobilefree.ru are for free coz i tried registering on that site and tried to download some stuff but there’s a price on it. btw, is there a tutorial on your site on how to install linux and how to use phonexs in linux OS? thanx!!!
best
what?
amigo2008
no tutorial for installation of linux…only flashing stuff..
and for firmware…
search on 4shared or google it
mobilefree mostly comprise of free patches…not all stuff is for free..
far contains jdflasher
firmwares contains of course firmwares…
and same with others
hello master, i’v just completed CrossFlashing my K550 > w610 before this tutor out. and now i want to flash quick access patch into my phone. i want to ask about the flashing main and fs, is it necessary if i rollback/re-flash my main and fs???? or do i need to re-flash them???
my k550 status now at w610 without QAP….
help me out, thanks
sorry my english is bad
just apply qap…and reflash using rest file…that will repair ur main…and phone will work
sir bhuvan, i would like to ask how do i know if im downloading the right firmware for my phone. when i tried entering R8BF003 in the search bar in 4shared there are many search results like
K800_R8BF003_MAIN_GENERIC_WI_RED53,
K800_R8BF003_MAIN_GENERIC_WI_RED52, K800i_R8BF003_FS_CENT_EUROPE_CID53, K800_R8BF003_FS_C_ASIA_RED52 etc. how do i check my phone to know the exact R8BF003 and what is the approximate size of the firmware to be downloaded?
@bhuvan
i see in this tut that there is no mention of the sim-lock-patch for cid53…..do you need it so any sim can be used instead of using the old sim that came with the phone………and how to apply the sim-lock-patch?
amigo2008
u need one main and one fs
version are correct..
get which matches ur erom version
like if its cid:53 then red53
if cid:52 then red52
best
after u do this procedure….u just need to apply that patch…
download the patch generator from our filebase
Hello Akshayy, I also have K530i –> W660i, with the firmware R8BB001, and I follow your video tutorial , how to apply patch using JDFlasher. But I got problem with creating mkrest2. When I drag and drop my firmware into mkrest2.exe. It doesn’t work. Just because my CID is 53. So could you give a good solution in both here and my mail. thanks
Hi Akshayy, hi have a K810 R8BA024 version. i unlocked it using R8BF003 version and works fine, but if i use the workaround for installing the R8BA024 version it fails, when Changing to QA2020.xml mode the phone powers on.
any chance to have my version Scripts on Anycid? what is the diference between R8BA024 and R8BF003?
Tkx
Hello Akshayy, I still get trouble with your instruction either.
My firmware is R8BB001 (CID53), I can’t find any bypass file for that firmware. As you mean, I have to get executor.b that match with R8BB001, or I can use any bypass file for my firmware(CID53).
I couldn’t create the rest file for my firmware. What should I do? Please help me.
Plz sent the reply to both this site and my mail.thanks
i have k550i cid53 and i want to unlock (locked to Orange Network..) i have Main and FS of r6ca001 and also i have the costum pack…i tried flashing and patching but didnt work…when i run executor it says operation failed and i can see the executor file locked..I dont know how to solve this pls i am a newbie..I cant make rest file too..i hope anyone here can help me unlock my phone..i cant use the phone here in our country Philippines for 2 yrs now…so unfortunate….pls help me….i only have the quick access patch made..this is the only i have made….
@ Duy Pham
u can use any firmware to bypass u jst need to upload the executor.b as said in tutorial
My K790i Dead..Due to Wrong Flashing of vkp Patch..Pls Help
My mobile is K790i-R8b600c-cid 53
I am flashed K800-R8b600C vkp Patches using any cid JD flasher..
While i’m flashing i got error message like(I don’t know exactly) “Invalid memory/Address”…but i’m ignored &flashed…
Now my phone doesn’t Turn on…I can’t connect my Phone using my DCU-60 cable while i’m tried to reflash main firmware in JD flasher…it doesn’t identify my phone…
Pls give me d solution
Compumad, sorry no idea bout differences.
hmm interesting. what workaround are you using basiclaly ?
Hi Akshay, i’am using the”Note: If ByPass Package is not available for the firmware of your choice” one. maybe i’am doing something wrong i, dont know. i think that R8BA024 is the latest version, if i had the anycid file for this version i’am shure that that version would work fine.
Best Regards
Compumad
Hi Akshay …i have k550i cid53 and i want to unlock (locked to Orange Network..) i have Main and FS of r6ca001 and also i have the costum pack…i tried flashing and patching but didnt work…when i run executor it says operation failed and i can see the executor file locked..I dont know how to solve this pls i am a newbie..I cant make rest file too..i hope anyone here can help me unlock my phone..i cant use the phone here in our country Philippines for 2 yrs now…so unfortunate….pls help me….i only have the quick access patch made..this is the only i have made….
I’m sorry for being a newb. But I’ve researched and read through everything, I have updated the qa2020.xml into the scripts folder, I have been using the AnyCid that is provided here, I’ve been using the W580_R8BE001_MAIN_GENERIC_LA_RED53.mbn file as main firmware so executor would work and all the rest and qa files would be created. But after the step of running executor on the phone (in games) it shuts down and then I hook up the phone in FAR and I never see “bflash”. I can’t seem to get this directory to show up. I’ve reflashed the main soooo many times already to revive the phone. What should I do?
Well find out for which Firmwares the ANY CID files are valid, then downlaod taht firmware and flash the phone with that firmware. As simple as that. 🙂
then use those any cid files
sadly we don’t have any cid files for all firmwares for all phones.
well, first download the firmware for which ANyCID files are valid.
THen flash the phone with those firmwares, using jdfslaher, check out jd tutorial.
then unlock the phone using anycid files.
I am so happy just now i have unlock my k550i CID53..It was so great!!! Long Live to all behind this tutorial! Thank you from the bottom of my heart!!! AKSHAY !!!!
My original firmware is R6CA001 Main Orange and i flashed it with k550i R8BA024 Main & FS red_53 w/o flashin rest …(i just flash vkp patches including simox v2.2)and it works finally!!! Thank you very very much Akshay once again…from Philippines
This is the Guide i use to unlock my phone…
Note: If ByPass Package is not available for the firmware of your choice, Read Carefully.
We have bypass pacakges only for few firmwares. If you don’t find one for your phone firmware, then there is a other way to get around and apply patches. The method is the same, but there are few changes. Here is the Small Tutorial… Its almost the same as above. But you need to re-flash firmwares twice.
1. First Flash your phone with the firmwares for which the bypass package is available. You can download firmwares from topsony or seusers. Flash both the Main and FS. Use db2020 Script, Oflash as told above.
2. Upload the bypass files, executor.b executor.jar and customize_upgrade.xml to FS as told above using JDflasher. Start your phone.
3. Run Executor in Games. Phone will shut down.
4. Connect phone with qa2020.xml and Flash the Main firmware via COPY (F5) of your choice which you wanted. Don’t flash Rest File. Its not needed.
5. Flash Quick Access VKP via COPY(F5).
6. Disconnect. Connect again with db2020 Script OFLASH. Flash the FS of your choice.
7. Connect again with db2020 Script and Enter OFS, upload CDA files. Close. re-insert battery and start phone.
8. Now you can follow Part 4, to apply more patches.
Philionthosh
Thanks.
Rest File Problem
i had successfully unlocked my k550i r6ca001 cid53 without rest file..because when i drag the main firmware to makerest2 software it doesn’t make (just nothing happens) but then i found out that the location for rest file produced was not on the same folder as makerest2 software located…As i have dual boot xp and mac osx 10.5.6 (hackintosh)…i boot to mac osx and was looking for a file and i had found something with .rest extension and i don’t remember anything that i had downloaded a .rest file..it came to my mind that it is the rest file produced by makerest2..so i had booted to xp again and tried to drag .mbn on makerest2 and i figured out that it does really work….the rest file located on my computer was on C:\C:\Documents and Settings\(your username here)…I hope this will help everyone!!!! or try finding anywhere else on your hard drive it might be on there…just dislocated by makerest2 software lol…Anyways….i didnt tried the rest file yet but hopefully will work and solved everyone’s problem!!! Goodluck!!!
(edit) Rest File Problem
C:\Documents and Settings\(your username here)
Philntosh, make rest works 100% with command line. Some times it does not work with Windows Explorer.
ok thanks.
Hi Akshay…
my k790i not working due to cross flashing……
i’m cross flashed my k790i-cid53 phone to k800..under k800 mode my phone worked well …but lost d signal…& also i can’t charge my battery using d charger…..
so again flashed my k790i firmwares…my phone shows only d WHITE SCREEN or SONY ERICSON STARTUP SCREEN…
again i’m cross flshed to k800 to check whether my phone work or not ..my phone is working but lose d signal can’t able to charge my battery also..
pls give help me…what could be d problem?
Arun
flash to k790 and then re flash using seus
then check out if ignal is coming
if not then hardware fault
akshayy
r u from india?
ansgaiims
well u need to run qa scrpit instead of db2020 now!
akshay is not here for few days again till i am here!
HEY YAH!
i drag my MAIN on to MAKEREST exe and get nothing, so i read carefully all comments and find out, that REST file is located on C:\Documents and Settings\ ‘username’
as one of comments poster said 😉
thank you all, btw im now try to patch unlock w200 cid53 😉
GREAT!
Hi Bhuvan….i’m updated via SEUS but still d same problem..i don’t think it is a hardware problem bcoz in d crossflashed mode(k800) it working well except
1.NO NETWORK COVERAGE
2.can’t charge d battery..shows d ALIEN BATTERY..
wat may be d problem…GDFS problem..?any other way to complete flashing (EROM)…?
Arun
forget about erom
this problem is very rarely found!
jump to our forum
ull get a lot many expert people there
discuss with them!
Help
Plz HElP me akash
em was using k800i rkg001_cid52 orange and i flashed my phone to k810i r8ba024_cid52 with patch by using xs++ and setool but my phone was getting reboot when i get any incoming call n even i was not able call anyone it was jus getting rebooted jus 3 dayz back
yesterday i updated my phone
now it got changed to cid53 k800i when i start it
shows the demo of k800i so i think it is now k800i …
help me what i should do now main difficulty em facing.. it says insert correct sim
18:10:32| Baseband ID: 9900
18:10:32| Protocol Version: 3.1
18:10:32| Phone name detected!
18:10:32|
18:10:32| Profiling SEMC phone…
18:10:32| Platform: DB2020
18:10:32| OTP CID: 51
18:10:32| EROM CID: 53
18:10:32| EROM Color: Red
18:10:32| IMEI: 35908701xxxxxx
18:10:32| Phone ID: K800
18:10:32| Region: EUROPE_4
18:10:32| CDA: CDA102511/101 R2A
18:10:32| Firmware Version: R8BF003
18:10:32| EROM: R3A022
18:10:32| Ready for operation!
18:13:30| Sorry, your phone is NOT SUPPORTED
18:13:30| Error: Failed to send CSLoader!
18:13:30| FSX Shutdown!
18:13:32| Disconnected… Unplug the phone
18:13:35| Shutting down…
this is my phone info
plz help me
sry for the poor english
md
y did u updated???
uhh!
use jdflasher now
i have tried jdflasher bhuvan
its say error when em trying to open ofs
…
could u plz tell briefly what should i have 2 do
plz
plz
add me on yahoo
plz
my id is yaseen_206
or on gtalk
mdyaseenferoze
plz help me out bhuvan…
http://www.orkut.co.in/Main#AlbumZoom.aspx?uid=1633905665795791481&pid=1231263934719&aid=1231238710$pid=1231263934719
same error for me which is der in ur album
md
then no way out for that!!!
till now…no one figured out why its happening!
what you did for ur mobile i think u 2 faced the same prob ?
Hello to All,
My phone is k810i r8ba024 cid53
How can I unlock my phone? and what’s the procedure? thanks.M
md
yea…till now m not able to figure out!
jay_t
procedure is in front of u!!!
but u need original sim to make it work
Hi bhuvan, thanks for the reply.
What do you mean original SIM?
I already downloaded anycid folder. But when I checked the K810i folder, it seems that the r8ba024 is not there. The only ZIP folder I found is R1KG001_CXC1250811_GENERIC_SM and R8BF003_CXC1250811_GENERIC_SM
And finally where I will get the firmware folder? Thanks
Hello pls help me i have a huge problem…
I have R8BF003 CID53 k800i and in the part 2 I tried to flash the “prgCXC1250210_GENERIC_WI_R8BF003.rest” file in my mobile and because my phone didn’t have a bflash folder I went to oflash folder…When i did that I had an error “PutFiles<putfile<putfile_flash<flashbabe<get89data>>>>”
I tried then to open my phone but it’s dead…can u please help me…I don’t know what to do
tnx in advance!
hello akhsayy….
my phone software : R8BB001, cid 53
there is 2 file on patch any CID for “w660i” :
R6AD001_CXC1250446_GENERIC_FY.zip
and
R8BE001_CXC1250446_GENERIC_FY.zip
what type is match with my w660i R8BB001 ???
can i request firmware, .MBN for w660i that match with R8BB001 ???
thx akhsayy…. i’ll wait your answer….
and sorry for my poor english 😀 😀 😀
hello akhsayy i have w660i
my phone software version is R8BB001
there is 2 file on patch any CID for w660i
R6AD001_CXC1250446_GENERIC_FY.zip
and
R8BE001_CXC1250446_GENERIC_FY.zip
what should i choose ?? for w660i-R8BB001 ???
can I request firmware, ” .MBN ” for w660i that match for R8BB001 ??? please… help me akhsayy….
and thanks for the video
akhsayy,can u help me??
why i cannot open executor??
its says operation failed??
can u help me with this?
can anyone help me??
i donno what tha probem,after i put executor,executor b. andcustomize upgrade,i open the executor at game,but it doesnt power off,but look like text
irfadz, relfash FS and try again 🙂
akshay,i try to reflash,i do all the thing in the video,
i open the executor,but my phone wont turn off,it open like some kind text or something.
can u help me;(
ok ill try reflash. if i have any prob i let u know.
btw,how to reflash FS??
what the use of simlockpathgen?
what does it do?
im sooo donno what to do..
why its so hard to do this??
akshay,i try so many time,but my phone wont turn off.executor open like text ;(.
do you have any suggestion?
qiuck replay plsss…;(
akshay,do i have to delete all in my custom?
if i delete what will happen?
does it break my phon?
somebody help meeeee….
akshay,why i cant flash my FS?
putfiles<putfile<putfile_flash<flashbabe<header>>>>
putfiles<putfile<putfile_flash<flashbabe>>>
irfadz. relax and clam down. read this once again.
why don’t you join our forum and talk to people in there.
may be the Fs you are flashing is corrrupt ? download another one and check again.
ok im relax.
what is ur forum?
btw,i already download new Fs.
i do all the thing in the tutorial.
i open tha executor,bt it says operation failed.
its been a few days i try this.
i donno what to do.
i just wanna put flash,patches,etc.shishh
Akshay ,
why my phon cannot open?
i already finish the setup.
can u give me the solution?
ifradz, our forum is se-lifestyle
come and talk to me and others over there 🙂
does this also work for DB2010 CID50 patching? namely w810 CID50
Sorry It won’t on CID50
I am so happy just now i success flash my k810i CID53..Now i can patch my phone..It was so great!!! Long Live to all behind this tutorial! Thank you so much from the bottom of my heart!!! AKSHAY !!!!
ashkay,can u guide me?
how to put flash themes on my phon?
btw,i succesfully flash my phon.
thanks to you ashkay.
ohh yeah,how many can i put patch on my phone in one row?
Hi
i can’t make rest file. i tried 2 flash my w880i with k810 rest file but didn’t work.
Can any1 send me rest file for W880i R8BA024 CID53 plz?
Should be named prgCXC1250***_GENERIC_AI_R8BA024.rest
The stars i don’t know but i think it’s prgCXC1250640..
plz help me
forgot…my mail adress is [email protected]
sry for doublepost
It works! I used the tutorial on my K770i on Voda.
I wanted to remove the SIM lock so had to use the Generic Main firmware -it means I debranded at the same time.
The link to SIMOX tool needs to be updated for V2.2 so it works with CID53 phones.
Also I’d point out you need a SIM for the locked network to get the phone working enough to run the executor.jar!
Now I want to apply patches but everything listed on TopSony is for K770_R8BA024 and I’m on K770_R8BE001 does that mean they won’t work? How do I up-issue the patches?
akshay,what is simlock?
explain wisely please..=|
why i want to put patch on my phon it syas line error??
something like that.
THANK YOU AKSHAY AND CO TEAM. REALLY HELPED ME WITH MY UNLOCKING.
i have the same problem as irfadz. when i try to execute executor it says operation failed.
what did i do wrong ? can someone help me please ?
after the 5th time i found out that it is working when not to re-insert battery after the part 2.
maybe this could help someone
DrK
Then you have to use R8BE001 firmware. else covert those patches to your firmwares.
akshay!!!
thank to you,i now can patch any patch that i wont!!
i also can put flash themes!!
yahhoooo!!!!
akshay do you have patch cyber shot for my w580i??
hi
i´m following your tutorial, but have to stop at the point where mkrest2 has to make a backup – I place my firmware over the mkrest2, a window flashes, but no new file comes out. can you help?
S500i
R8BE001 CID53
S500_R8BE001_MAIN_GENERIC_LY_RED53.mbn
thanks
found it, thanks
me again. couldnt continue at part 3 because my phone is locked, I cant access Games->executor. any help? thanks
Help me?
How come i still have R8BC004 in the software version menu although i already flashed it using R8BE001 ???
Hi.
Is there a way to patch unlock a w610i cid53?
Regards
ondrej, that’s bad, really sorry ! i have no idea how to proceed then.
groovepepy, have you flashed your FS or not ? you need to have R8BE001 FS then you can see it.
Anderson, this is the method if you are lucky, else don’t. seriously, i feel idiotic.
hi Akshay I have problem when i open bflash my phone will turn on and far say me an error what I do wrong
p.s. my restmaker2 didnt get me any file when i drag my firmware on it its W610_R8BA024_MAIN_GENERIC_NA_RED53 can you help me??
my mail [email protected] thx
follow back the steps again
its because ur phone’s security is not cracked!!!!
apply qa again
for rest file
follow manual cmd commands
which os u are using?
what do you mean follow back the steps again?? How i can crack my phone security?? and fo cmd it dont work I run it but it turn off after 1 second
I am using windows xp sp3
sorry fo my bad english im from czech rep :))
Lukas
cracking phone’s security is cracking main…so that u can apply patches
untill u dont do that…ur phone wil start when u enter bflash
by cracking main in other words by apply qa patch…we make main dead and phone is no longer usable….
but by flasking rest file…it revives back!!
and is patchable
and on which drive u are using it?
try using on other than on ur system drive
if u still do not succeed…then jump onto our forum and request rest file there
now its ok but when i flach rest file and copy qa ptch i disconect phone but phone dont start what im doing wrong can you hel me??
sorry im lame :))
iv got it first i must instal qa and then rest??
Lukas
yup first install qa
then rest to bring ur phone back alive
but it dont work my phone dont start up but i keep try it more time . I can have a a luck
Lukas
discuss on our forum then
akshayy you are really such a great help for all of us, ur one of the geniuses ive met when it comes to modding SE (thanks u x10000000)
hey akshay…
in step 3(i.e.installing Quick Access) of ur tutorial(any CID patching) u have mentioned that one is supposed to copy d rest file(as vkp) into bflash folder….but in my fone no bflash folder exists! do i have to create it ? please help…i have only 2 folders – OFS & Oflash…& i am using a w580i CID53 fone…
nosremo
good luck
akshay is off for few days
napstar
u have to select qa2020 script
u have selected db2020
you were absolutely correct bhuvan…wen i chose qa2020 script,i found both the folders bfs as well as bflash…!!
but wen i try2 access any of these folders i get the following error:
”
found EPIUSB2
connecting…
got response
protocol: 0301 baseband: 9900
cid detect
<- cid=53 color=red platform=db2020
qhtry: 2020_prologue
run flashed loader
error: SetDirectory(setdir(setmode(doscript(run(gethello(I0usb::getblock(time exceed))))))) ”
i replaced the original qa2020 script wit the one provided by u guys…(in the anycid package) these folders did not open then…so i therefore restored the original qa2020 script & tried opening these 2 files…but none of them opened & gave me the same error..
please help….
thanks;)
hey bhuvan,i forgot to mention that my EROM is R3A022…& as the error occurs when the flash loader runs…i checked the bin folder in JDflasher directory…the bin folder does not include any file for R3A022…i also downloaded the latest version of JDflasher(test 6) & also the addons that were available on the internet.but still there is no file for R3A022..
can u please look into it & suggest something??
thanks. Help is appretiated 🙂
napstar
damn!!!
why only w580 users are getting this error
i am really very sorry to say this but there is no way out yet for this error!!!
even i am getting this error…so i hope…ull get that…no cure for it!
@bhuvan
thanks for lookin into it anyway..! i hope that somin is possible in the near future…! 🙂
cheers!
Hi everyone,
I’ve been using this tutorial to unlock my CID53 w610i. I follow step by step of this tut and it’s all good until I turn my phone on and it stops responding when looking for the operator…the second time I tried flashing new firmware and FS (R6BC002) after running the executor, but still phone behaves the same way, it hangs when searching for the operator, I was hoping that someone could help me and if there something else I could try…Regards
Claiton
i guess there is problem in firmware file
get new one
and still if it hangs then wait for more time
how time did u wait for?
“Go to Entertainment and then Games. Run the executor in games. Your phone will turn off.
Now Re-insert Battery. Don’t start the phone.”
But i can’t access the phone without vodafone SIM card.
When i turn it on, it’s just asking fligh/normal mode.
Both will give same results, INSERT SIM CARD / INSERT CORRECT SIM CARD.
W880 CID 53
Any Idea ?
ryan-isra, oops. sorry, try to reflash phone with SEUS and see it starts again.
good day!! im about to enable patching in my k800 cid53 phone and i was able to prepare the necessary files to be uploaded in my phone but when im about to perform part 2 of the video tutorial, when i start farmanager and selecting the db2020 script and unchecking the rsa, i can’t see a bflash option only oflash and ofs thats why i did not proceed in patching my phone. please tell me what to do so that i could see the bflash option. do you think this has something to do with the farmanager that i’ve been using??? im using farmanager with jdflasher plugin cid53 and that’s what im using for changing my phone’s acoustic driver etc. btw, for example i did not succeed in enabling patching in my phone and it got bricked, does it mean that i cannot do something to revive my phone and cannot even send it to phone repair shop here in our country??? please help me!!
amigo2008
use qa2020 script for patching
y dont noobs read all steps carefully?
yipeeeeeeeee!!! at last i’ve done it. many thanx to all geniuses who helped me!!! now it’s time to install those awesome elves in ma phone!!!
i have a k810 CID53 r8aba204..
i cant find the files in anycid folder.
can anyone help me flashing my phone so that i can upgrade my sucky camera driver? thanks in advance! 🙂
r8ba024 i mean
doi,
flashing is easy, just connect phone and select ofs to enter File System and also select oflash if you want to flash firmwares.
Use other firmware to apply QA if you want to patch.
good day!!! there’s something that i would like to ask. so now that i’ve enabled patching in my cid53 phone, do i have to uncheck rsa everytime i do patches like for example if i patch the elpack.vkp or you have to just have to uncheck rsa when your enabling patching to your phone????
amigo2008
nope
u can do it without bringing any change to rsa
Hy all. I have trouble when i try ti open the “bflash” folder and i get this: error: SetDirectory(setdir(setmode(doscript(run(gethello(I0usb::getblock(time exceed))))))) ”
plzz help me i need to unlock my w880i locked toa hungarian operator:|
plz contact me by email: [email protected] or add me on Y!Messenger as totike_90
thx before
totike
there is seriously no cure out for this error..
even i face the same when i try ptching my cid:53 w580
u may get ur problem at out support forum!
Hi guys,
I have a locked W610i Cid53 which I will try to patch unlock, my question is after I load the necessary files and run the executor in games, is it recommended to use bflash to flash to the latest MAIN + FS (instead of keeping R8BA024) and then load the patches etc…
Thanking you
Claiton
I am not being able to create the “rest” file…
I think the “mkrest2.exe” is not working properly….
Please Help..!!
What Should I do..??
Claiton
u need to flash by bflash be cause ur actually not reflashing main…but repairing it…keeping main’s security cracked!
Navjot
whats exactly happening?
try on different dive other than ur main drive
got all administrator privileges?
I was talking abour the rest file which we drag onto the “mkrest2.exe”
But I got it…
It gets saved in X:\Documents and Settings\user name
Navjot
lol!
njoy then
Hi all
CID53 W610i unlock patch.
After I apply the remove sim lock patch my phone starts normally but as soon as it logs onto network it stops responding and after awhile it restarts itself and this process happens over and over again…any ideas please thank you.
Claiton
Claiton
u sure that ur patch is working one?
Hi bhuvan
Yes it’s a generated patch, I used SimLockPatchGen 2.2 to create the R8BA024 remove_sim_lock vkp and I’m running R8BA024 MAIN and FS.
The patch works because my phone quickly logs onto Vodafone (previously locked to Orange) but sometimes the phone hangs after logging in to network and restarts itself.
btw, what is sysgfx or gfx patching??? what is that for??? can i also make that kind of patch in my k800 cid53 phone. i found some cool patch in mobilefree.ru especially the walkman 2 patch and record fm patch but the first sentences are in russian. can i still save those patch in notepad and patch it in my phone or i can translate the russian characters using google tranlate???
Claiton
then do one thing
after unlocking flash ur main to non branded one
i mean generic
amigo2008
no
save according to original characters
no translation
and yea
u can use
patches are firmware dependent…not erom
Bhuvan
re: w610i above, but after unlocking if I flash main isn’t that going to overwrite the patch therefore locking it back up?
Akshay, i already re-flash it.
It’s similar with my E90 before, can’t do anything without
correct SIM Card, even in flight mode (SE).
For E90, i bought the unlock code.
I think i must use D-unlocker to downgrade CID first. Thx anyway 😀
Debrande and then apply unlock patch
Claiton
damn!
this is confusing!!!!
i am telling u to do this because may be the main which was installed on ur phone earlier has something which binds ur phone to work as unbranded\unlocked!!!!
experiments is the thing which we can do!
really? we don’t have to translate the russian characters in english?? when i save the patch with russian characters in notepad there’s a prompt ” this file contains characters in unicode format which will be lost etc etc.”. and when i open again the patch that i saved with the russian characters, it’s replaced by question mark. is this normal????? btw, how should i delete a patch?? can i double click memory and view the patches that i installed in my phone and select the patch that i want to remove??
amigo2008
just straight forward save them and about unicode thing…just click on yes!
it will work..even i dont have russian installed on my system
deleting patch is given below
check it
its same as applying
u just have to check remove patch!
helo…
im have prob with my w66o…cid 53
i run it with xs++ n far manager ,,
it doesn’t work ,,,
whyyyyyy
hi i get to the stage where i go to Entertainment-Games and then run the executor file, however it says ‘operation failed’. I have an s500i, and I am certain that i need to use db2020, and the firmware exactly matches the one on my phone? any help would be appreciated thanks
james
ya firmware should match
if its not matching then reflash to version to which is matches
then upload 3 necessary files
it will work
and sorry where do i actually find the firmware that should match with my phone, is it on this site, and once i get that can you reflash in jdflasher? thanks
sorry also bhuvan to bombard you with questions, but when i go to flash a different firmware the following error message arises:
PutFiles<putfile<putfile_flash<flashbabe<header>>>>
know what this means, thanks
james
its the problem with the firmware
its not compatible with ur phone!
download one for ur phone from
http://www.topse.ru
or topsony
once u get them u can reflash anytime
thanks for all your help bhuvan, everything went perfectly, however my original intention was to unlock my phone, however only just discovered that you can’t get a vkp patch that unlock’s cid53 phone. Would you know of any that might or could be in the near future?
james
no!!!
i guess way out is there
check out at our forum
or ask there
helo…
im have prob with my w66o…cid 53
i run it with xs++ n far manager ,,
it doesn’t work ,,,
whyyyyyy
please help me ,,,
kutob
use jdflasher
Hi I have the problem that my phone (k800i R8BF003 CID 53) wont turn off when I run executor.jar in games.
It says “Operation fehlgeschlagen” (german phone) what means Cant run
I Re-Updatet the Phone whit SE-Update Service but it still wont work
Its whit Vodafone Branding
Leo
r u sure u have uploaded all the files to correct dir?
yes i´m sure
when I boot the mobile it says please wait
When I want to start the executor it wont work
and when i look with far after the files they away
I have a K550i @ W610i (R8BA024-CID53) . and i want to install elfpacks… so i guess i have to follow this procedure and then http://www.akshayy.com/sonyericsson/pimping/elfpackelves/ procedure…
1) am i right??
I went through the page and the video….
but when i started FAR manager and entered into my mobile, i cant see any folder named “bflash”….. i only have “oflash” and “ofs” folder (or whatever those are)
I have not started the next steps after that, because i have 1 question about it…..
*** will that “bflash” folder automatically appear/created after i complete “Part 2: Flashing, Copy Breaking files to File System.” and running executor from games folder????? ….
or
that “bflash” folder should have been there, in my mobile already… and it has a prob….?????
In the Video there is already a folder named “bflash” at the start of jdflasher…. i am talking about that.. because my mobile does not have one currently….
By the way….. is it any prob, that i have CID53??? or these can be done in CID53???
(i am asking this question because in anycid folder i have to use the contents of the folder “2020-52″…. i thought that is for cid 52 only. or that is applicable to cid53 too??)
another Question..
@Bhuvan….
you said in the 2nd page…
“the error is coming because you havent uploaded the cda pack
get it one of your region
they contain few netwrk tweaks…
google it
like cda [fone model] region”
what is CDA and how can i update it before proceding…???
after I press >*<<*<* i get into the systemsoftware info and looked into it. it says:-
Customization
CDA 102568/207 R2A
cxc1250755
R8BA024 99E0W VFE_2
is it ok??? isn;t it got updated when i flashed my k550i to w610 and used custpack ??? or do i need to update it in some other procedure…??? oh!!!! 🙁
when flashing k5501 to w610i
i used:-
W610_R8BA024_MAIN_GENERIC_NA_RED53.mbn Main…..
W610_R8BA024_FS_VFE_2_RED53.fbn FS
i remember i used a custpack of HB1-06_Gen_CDA102568_207_R2A_GENERIC_CENT_EUROPE
Is these things are OK for the patching??? or i need to change the CDA???
Leo
check they must be going into doja folder in custom folder there
just dont open the custom
just drag and drop all the files on custom
i mean open tpa/preset/
drag all the files on the place where custom is there!
lovedimpy
first kear how to patch cid:53 phones
bflash will come up in qa2020 script
follow the way it is given
then follow how to use patches!
to allow patches to be executed u have to patch ur phone
lovedimpy
whoa!!!!
so many queries!
in the video bflash is there because its akshay’s phone[cid 52]
in cid 53 phones it wont come up
u need blash later…ull get it when u use qa2020[updated one] as the script
u can of course use elves on cid53 phone
if phone aint getting any error then ur cda is right
dont worry about it
a lot many versions of cda pack keep coming
patching do not involve cda pack at all
cda update in anycid just makes ur phone ready to be used by executor
you said..
“first kear how to patch cid:53 phones”
is there any other procedure for that??? how??? 🙁 :confused:
and thanks for answering 🙂
i know i am questioning a lot… but i am down in bed with broken leg… cant move around..
sorry for asking a lot 🙁
i have done all the procedure….. it went well……
But….
Now there is a problem after i patched the mobile with Elvpack… 🙁
after patching it, when ever i browse through mobile to phone>other>zbin or sometimes even only into file manager….. or even browse through MyPhoneExplorer 1.7.3, mobile getting restarted 🙁
i followed every step as said…. 🙁
should i remove that elfpack???
i did all but it wont work
all in the custom folder
it says operation failed
and after bootlogo it says i should wait
lovedimpy
oops
i mean learn patching cid53 phones first
lovedimpy
try browsing through filetransfer mode
how many patches other than elves one u have applied?
Leo
ya
u have to wait
cda will be installed and phone will boot
is ur phone cid:53?
oh. cant see my posts. posted 2 times…. 😮 am i blocked or something? 🙁
well….. thanx 🙁
Oh.. i have done it at last… looks like my elfpack which i used previously was corrupted/outdated……
lovedimpy
if we would have blocked then i would not have been rplying this
lol
anyways great!
Hi everyone. Can u help me with this? my firmware don’t have a bypass package. i’ve read the turorial abt this but i still don’t get what it means. Must I change my firmware? Or should i find a bypass package which suits my firmware?
John
change ur firmware
Ok Thx bhuvan.
will you guys make the bypass package for r8bb001 w660? because i heard the rest of the firmwares don’t have much patches
i don’t get it. if i have to change my firmware, why is patches for r8bb001 when there is no bypass package for r8bb001.
John
ask doubts here
for stuff go to our support forum
John
we have given a way out for ur problem
still cant make ur own demand at out forum
How can I patch WITHOUT Quick Access ?
aLt
no way of patching without braking main…qa helps breaking it
sorry for this dump questions but im still new at this so is there any executor.b for w660 r8bb001?
hey
i forget to look an yes my phone is cid 53
i want to patch with this tut because its cid 53
Ridik
if there is no bypass package available then ull have to make one like the way it is given at the end!
Leo
then what?
I can´t run executor.jar
why?
the date in custom folder get lost after boot phone
Leo
date???
whats happening when u run it?
it says operation faild
i just master rest my friends w850
i reset it all by going to menu > settings > general tab > master reset
but now the phone does not want to work
Leo
exact error?
guy with k850
so whats happening now?white screen?lagging?
if white screen then reflash
the k800 just says Operation Failes
not more
Leo
when?
what about the w350 the flashing and unlocking?
when i start executor.jar
well when i turn it on it stays as the wallpaper and i can’t see any thing
but its ok now i fixed it
i reflashed everything
when i run executor it tell me operation faild…PLEASE TELL WHAT TO DO.i need HELP.PLEASE RESPOND.
I have the same problem here. Once I move MAIN on mkrest2.exe nothing gets created :(. I read somewhere that these files get created in Documents and Settings\Administrator, but they are nowhere to be found…
I have CID53 DB2020 and I tried to apply quick access (which, btw, was created without a problem) and jdflasher warns me that 4 bytes mismatched and asks me to continue. When I continued the QA got flashed w/o problem, but ever since then I can’t turn it on. Got panicked, of course, and cold sweat covered my back, but I tried to oflash it with firmware and luckily it helped and now I can turn it on again. But my problem still persists 🙁
Enso
qa brakes the security by cracking the main
this causes main to get corrupt
rest file repairs it in way so that security is no more there and main gets working fine
flashing whole main back again gets security back!
i guess this clears ur questions more!
and for mkrest
try making it somewhere rather than os drive!
drive on diffrent pc running win xp
Cheers, worked on two CID 53 K800i
Copied the 3 files to phone – ran executor – phone turned off
flashed rest – then quick access – restarted – then sim unlock
I generated the 3 VKP files from a generic firmware with the same numbers as my original R8BF003, this was also CID53
If I had problems I would flash the main and restart again ( I think I had to copy CDA over to avoid configuration error). I used a compatible sim after re-flashing to start again because sim lock was still active.
By the way, I think the rest file that gets generated is saved in C:\Documents and Settings\your name here – I can’t remeber if it’s hidden – just show hidden files in folder options.
Don’t forget to copy the files from Anycid
Rooster
great!
Hello again bhuvan now i try to flash a w200i phone.Everything go well till i need to lad the correct main in the phone.I get this error setdirectory setdir setmode do2010_49 unknow cert.I have follow this guide If ByPass Package is not available for the firmware of your choice (abowe).What is wrong?
klingan
the flash for one firmware for which it is given
or look more in the guide at the end
ull find ur answer
bhuvan i have start a thread in http://www.se-lifestyle.com/viewtopic.php?f=16&t=2894 i be greatful if you can read it and give me some feedback
my k800 when i run executor keeps coming up with operation failed. I have repaetd the process over and over again and for some reasn the phone doesn’t turn off and it keeps coming up Operation failed. What am i doing wrong!!!!
HELP!!!!!!!
JAMES
reflash to a compatible firmware and upload the right files
all three
I’ve solved the problem a few days ago and now I have fully working unlocked phone. I had SE K770i CID53 DB2020 with R8BC004 TMOBILE and here’s what I did:
– oflash to R8BE001 GENERIC as executor for K770i works only with this one
– ofs executor to phone with supporting files
– run executor from phone
– bflash R8BE001 GENERIC (this time w/o errors)
– bflash pregenerated quick access patch
– bflash pregenerated sim unlock patch
After this my phone was unlocked and working. But I have new quiestion. Most patches are made for R8BC004. So if I want to apply a new patch will it work? -or- If I oflash the phone to R8BC004 will the quick access be still there? And, more importantly, will the sim unlock be still there?
PS. I never used rest, as I couldn’t get it created, and I read somewhere that it is not needed.
Enso
no
find patches for ur firmware or flash to R8BC004
bhuvan:
Flash to R8BC004. But how? oflash or bflash? Will quick access remain, or do I have to repeat the steps all over again?
Enso
through any script
our main aim is to get firmware which suports max patches!
of course qa will no more be there
ull have to do that again!
Hi i hav SE k810i,Cid 53. but executor is not working…
i hav read da whole procedure & seen tutorial video of Far Manager with JDFlasher plugin….i got stuck aftr step2 …when i click da executor its show “Operation Failed”tht means i cant go 2 futher steps..
i guess all executor.jar is 4 CID52 cos when i click da zip files it shows 2 files Cid52 & Meta-Inf…and mine is Cid53….
so plz help me 2 go further..
even if i go 2 step4 tht means Patching.vkp file its shows error.
really need help…plz guide me…
Nasimul
u r stuck upon a lot of stages!
dude anycid is for cid53 phones only!
first ull have to break ur main then patching vkp will work!
well give a try
reflash ur phone fs and main and cda!
dont forget to take the backup
and then upload the right firmware compatible files to tpa/preset/custom
if still doesnt works then post back which firmware u flashed ut phone
which files ur upload and where
Its not working still showing Operation failed when i click da executor in da game menu.
Mine
09:54:49| …using GDFS name
09:54:49|
09:54:49| Profiling SEMC phone…
09:54:49| Platform: DB2020
09:54:49| OTP CID: 51
09:54:49| EROM CID: 53
09:54:49| EROM Color: Red
09:54:49| IMEI: 35315302xxxxxx
09:54:49| Phone ID: K810
09:54:49| Region: S_ASIA_LEVAN
09:54:49| CDA: CDA102779/87 R1A
09:54:49| Firmware Version: R8BA024
09:54:49| EROM: R3A022
09:54:49| Ready for operation!
As u said i hav reflash my phone fs and main and cda! and then uploaded the right firmware compatible files to tpa/preset/custom without any error!
so i hav download da followin
FS:K810_R8BA024_FS_MEDITERR_RED53.rar
CDA:K810i_CDA102779_87_R1A_Customized_India.zip
MAIN:K810_R8BA024_MAIN_GENERIC_SM_RED53.rar
Firmware:K810_R8BA024_MAIN_GENERIC_SM_RED53.rar…
after tht once again i hav copied 3 files executor.b, executor.jar, customize_upgrade.xml to tpa\prest\custom in the phone’s file system.
then also not workin .. now what shld i do ..
& my mkrest2.exe is not workin its doesnot generate any file after i drag da firmware in it.i have teried many time..
so i hav downloaded da .rest file tht is
prgCXC1250811_GENERIC_SM_R8BA024.rest..
need help…..
Nasimul
forget about mkrest cuz we are not upto that level yet!
i suggest u to jump onto our forum
many guys there
ull get a lot of solutions
one of them will surely work!
i can write so much here!
Hi, i have big problem
i flash phone very coeerctly, when i disconnect phone from USB it doesnt eork ! 🙁
please help
whiteberry
does not works?
what really happens?
now its ok !
I reflash my phone ! ^^ 🙂
but i have now 1 question i flash my phone to k550i@w610i
…
When i install programm in phone it show me operation faild
and i have DB2020 RED53 W610_R8BA002
Hey what about SE W350
i don;t know which script should i choose
by the way what this flashing will do to my phone ??
please help…
whiteberry
reflashing the fs while cure it out
it must be happening with every app
vinayak
u have to use pnx5230
n which flashing?
reflashing fs and main gets ur phone out of problems!
u are just installing the whole firmware again in it
else there is lot!
be more precise
HI! Im planning to start on learning on copying patches onto my w580i phone. Be4 I was finding awesome flash mega packs but one of them has a battery patch (iphone). So to do this I need 2 install QA patch on my phone. just wanna clarify a few things in case of any errors… If using different MAIN firmware u get an operation failed when starting executor right? bflash option would come up with a cid 53 phone after transferring the 3 files(and selecting qa2020 on starting jdflasher)? Last when ur sim card gets deactivated, it still works on an locked phone so that u can reinstall the unlock patch after flashing and switch back sim cards( so keeping sim card as unlocking backup card)? Sorry for many questions but I want to get all the information on my head be4 I do anything extreme 🙂
jeremy
1.operation failed comes due to few reasons only!just upload the three files to right place which matches ur firmware
even if u are going way right n still it appears reflash the fs and will get it solved
2 bflash will come up when u use qa2020 as script.
3 yea
u can relock the phone by applying the lock patch
still a not into locked phones so i suggest u to jump to our forum and ask the third thing there
😉
Hi I’ve Used Your Method To Unlock My K770i But I Stuck With My W350i… I Need To Know What Executor.b File To Use, As The Tutorial Doesn’t Refer To Where To Get, Or Which File To Use… Please Help!!!
how am i supposed to do this part???
“Part 3: Installing Quick Access !
Go to Entertainment and then Games. Run the executor in games. Your phone will turn off.
Now Re-insert Battery. Don’t start the phone.?
when i cant go past the “insert correct sim card”
i have read two threads and both of these tell u to do the same thing….
are u guys stupid or something
if i could use my mobile i wouldnt be here
PAC2000
it is there in any cid pack!
Faizan Khan
better mind you language!!
we are helping noobz like u out for FREE!
ull need the sim to which th phone was locked!
dont have it??
enjoy the brick!
I don’t know how to do mkrest work with my k770i
please tell easy to do!!!!!!!!!!!!!!!!!!!!!
thank!
how do i go abt getting the bypass files for my w660 db2020 R8BB001 China_FY CID53 i know it is not on the any cid.zip. i understood the other steps. wud this involve flashing. i m not too confident of flashing and i dont want my only phone to die on me.pls help.and yes i m a noob but m comfortable with simple modding. hav never tried flashin thou.
k770i problem
just drag and drop the firmware file on it
Chaithra Shetty
well if u dont know flashing then u are probably jumping to higher stage!
lol
anyways
we are here
no worries!
read jdflasher flashing guide
and flash to firmware whose bypass files are available!
download firmwares from 4shared.com
search there
K770i Problem.
I presume you’re talking about mkrest not working with drag and drop ??
Had same problem, I used rest tool in xs++, drop your firmware on that and it made a file, then right click on the file and in the header add .rest to the file name.
Now it’s a usable rest file.
Just copy that when the tutorial tells you too and you should do fine.
I’ve just unbranded and unlocked my K770i from 3. So trust me it can be done.
All the best.
ASHJA5
nice!!!
hi bro,
sorry to intrude u with this noob question i got.
first of all my problem begin when i update my k800i with sony update software..
later after the update…any sim can’t work. from what i google around, the network extended lock.
so i begin to flash using ur method, dl the
K800_R8BF003_MAIN_GENERIC_WI_RED53
K800_R8BF003_FS_APAC_RED53
for my firmware. but stuck @
Part 3: Installing Quick Access !
Go to Entertainment and then Games. Run the executor in games. Your phone will turn off.
Now Re-insert Battery. Don’t start the phone.
i still cant even past the sim lock. what should i do?
sorry for u time.
Fruity
u need the original sim to run executor!
without it u cant!
sorry
but thats one of the main step
owh ok thx for your reply …
*get other phone to use :(*
Fruity
cant help!
Help me
I have a problem with my brother’s k610 cid52:
After opening executor, the phone turned off and then I took out the battery, but when I accessed the bflash (qa2020 script) an error message appear:
error! bla bla bla get time exceed!
So I did the bypassing step and applying QAP using setool lite, and got succeed, but untill now I can’t patch my brother’s phone using bflash if qa2020 script selected. Bflash can be used to patch only if I choose DB2020 script.
The strange things is I didn’t get this problem with my own k530 cid53.
Did this problem come from my far+jdflasher? Or it was because my brother’s phone is cid52?
fyi: both of my and my brother’s phones are crossflashed to w660 r8bb001 generic, because there is no anycid file for r8bb001, so I used the r8be001 one, and I flashed my and my brother’s phones with r8be001 main, after bypassing step I flashed
Back to r8bb001 and applying QAP for r8bb001.
Note: this is only work for my k530 cid53.
Does anybody know why this problem is happened only to my brother’s k610 cid52?
What is the cause of this problem?
Don’t say that I’ve done something wrong, because there is no problem with my k530 cid53.
wahono
ur brother’s [hone is cid52 and urs is cid53!
urs requires anycid method!
brother’s phone requires simple patching guide!
look in jdflasher[patching]guide
i am having trouble tryin to create a rest file from k800 r8bf003 cid52.
how i patch my k770 cid53 r8bc004 .bcz there is not exucuter.b and jar for this version in any cid.zip please help
Hi,
I’ve been trying to unlock my k800i (R8BF003 cid53) for several days now (using anycid), and read several tutorials on how to do so, however I keep getting the same problem – I cant access the bflash (using the qa2020 script to connect, when I use the DB2020 I only get the oflash and ofs).
The error message is: SetDirectory<setdir<setmode<doscript<run<gethello<IOusb::getblock>>>>>>
I’ve came across others with the same problem (such as Wahono from this post), but no one really answered them.
Don’t know if it is relevant, but I did succeed accessing the oflash and ofs via DB2020 script and load a firmware to the phone.
Any help would be appreciated!
Hi again,
After re-downloading Far+JDFlasher+Anycid (from the links above), and following the steps exactly as in the video (also, from the above download section of the post), it worked 🙂
Now my K800 is sim-free…
GREAT TUTORIAL! thank you
hi there Sir Akshayy!! can you also please create a video tutorial on how to apply sysgfx patch properly coz it’s very difficult to follow the tutorial that i’ve read in some se modding site. thanx!!!
Akshayy thanks for an easy to follow solution to unlocking my phone – a W580i !! All the best my friend………..
Catonthewebb
yes, i got this to work on a W580i with CID53.
took me some time and i needed a SIM from the provider it was locked to, but in the end it was unlocked.
thanks for this guide!!
were can i get patch for my w200i ? :0
Hmm..i found patch but when i try to make quick acces patch..its shows i cant :0
got w200
it shows Unsuported platform
Iahiru… u r not even reading….!
very usefull and clear post. many thanks. I sucessfully unlocked K770i from this method.
I have 2 questions:
I have K800i CID53 unlocked phone. are there any way to know weather it patch unlocked or permanent unlocked ?
if it patched unlocked, relock after flash main. then I need pay for unlock because I have no SIM for it.
or any way to use phone without its locked SIM/test SIM ? to run executor.
Symantec blocks qamaker.exe, and complains that this has a trojan.Vundo virus..:(
any help on this.
cialis germany cialis rezeptfrei kaufen shopzilla cialis cialis cailis bestellen cialis generika
shopzilla cialis
shopzilla softcialis cialis rezeptfrei kaufen sildenafil kaufen generic cialis 100 mg cialis ohne rezept sildenafil tabletten
Hi Guys…
I tried the above method (and thanks for the guide – really useful) to flash my k550im. I had to first flash it to K550, and then re-flash, but something’s not right. Now my phone won’t turn on and the screen just flashes on and off… Do I now own a nice-looking paper-weight, or can anyone help!?
akshay, after copy main firmware tht i want into bflash, and the quick acess,
u mention tht we can install the fs tht we want in oflash, but u didnt mention can we install the MAIN tht we want in oflash?
can? but must same with the one in bflash ofcuz.
and the “FS THT WE WANT” is it include different model?
anyone here knows how to have w610 main generic na with chinese lang+writting.
i tried flash fs china and main china, got chinese. but no patch .
when flashed main generic, fs china ,no chinese anymore…
help!!! anyonr knows?
can i apply this patch to w610i@k550i .
Hi. I have a problem with a FAR. When I start Far.exe, press Alt+F1 and then click “just da flasher” – FAR closes. Could you help me with that? :(((
^
|
|
My phone: SE W850;CID 53; db2020
hey guys how can i patch r8ba024 k810i? when to reflash the original firmware after patching qa? can u please elaborate it to me please.
also when i enter bflash after reflashing the main fw, it shows the error
SetDirectory<setdir<setmode<doscript<run<gethello>>>
help me pleaseeeeeeeeeeeeeeeeeeeeeeeeeeeee…
when i drag and drop the main firmware file (.mbn file) onto mkrest2.exe, the .REST file is nowhere to be seen….pleeasseee heelppppp!!!!
hey guys when ever i connect my phone to jdflasher there are always 2 options oflash and ofs there is no option of bflash ,,,,,what i have 2 do now
hey!! can u please help me? i wanna modify the battery icon as well as volume icon. so where i put the battery icons & volume bar icons?
i flashed my mobile k550i to w610i.
i flashed my mobile k550i to w610i.
i can’t see the bflash when bypassing through qa2020. There is an error message showing.
What is the problem i cant understand. I have R6BC002 w610i.
Gappa
ull have to learn patching for that!
now tell me whats ur phone’s cid version?
Thanks for reply.R6BC002 CID 53 RED
Gappa
cid53. allright! why dont you downgrade ur erom? that will provide you max support and even if phone malfunctions we will have it in our hands!
follow the latest guide for erom repair, its given there!
actually i wanna change my battery icon as well as the volume icon. so in this case what i have to do?
thank u..
he akhsayy ,i am not found executor.b for w350 in anycid folder .please add that.thanks
deepak sharma
sorry but w350 is not patchable!
i have downgraded my erom CID 52. Now what to do??
@gappa, check db2020 patching!
Gappa
great!
now ur phone’s every software related trouble can be solved and many softwares are compatible, and its always good to have cid52! congrats!
now look db2020 patching guide[not any cid method]
Thanks bhuvan.. it works…. can u tell me how can i delete a .vkp aptch?
Gappa
just copy the patch like u do when u apply it, when a dialog comes where u give command to patch, check the option saying remove patch! it will be removed
okay.. it works.. thank u very much….
is it possible to install camera driver of k790 on w610i?
i using this SE W705 and i copy a font using A2 uploader…and the problem is the can turn on…csn some one help me plass………..???? thx ….
drey88
u mean cant turn on?
u have to copy the .xml file also!
but hw is it possible?
Even u change or deleted font it starts just doesnt show anything or uses some default font!
ppg
no, if there is nothing in fonts folder then sometimes phone restarts
hi
can i get bypass package for k550 red cid 53 rbbc002
and since my phone is 2020/53, can i use the files from 2020_52 folder in anycid
alex1432
reflash ur firmware to other firmware version for which bypass package is available
can u suggest the appropriate by pass package?
alex1432
dude i told, reflash to a firmware whose bypass package is there! like r8ba024
R8BB001 prgCXC1250446_GENERIC_FY.rest file reuired and please send me full vid of thi in [email protected]
Hi,
I do everything as it should in step 1 and step2. When I come to step 3 “Installing Quick Access” it says: “Go to Entertainment and then Games”, but when i re-insert battery and start the phone, something is loading and again say: “Phone Locked” “Phone Lock Code:”
Can somebody help me to finish the tutorial?
I Have: SE K800i CID53
Than You!
vinu
jump to forum, ask there
APD
is ur phone branded or locked?
bhuvan,
is not branded is locked, not network lock, it’s Phone Lock.
APD
oh damn, since ur phone is cid53 anycid method is not working, and xs++ for win do not support cid53 phones!
ull have to sit on linux and use xs4.1 i.e. phone xs, that will help u
I try on Ubuntu, but i have problems with terminal,mising package “libfltk” and i cant install it from terminal :S
I SOLVED THE PROBLEM! 🙂
I correct the problem with terminal, and i reset the phone lock code to “0000” with xs++ 4.1 and Ubuntu.
Thx for your help!
APD
amazing u are among the very rares who tried xs++4.1 and operated successfully!
is this the way to change from ‘red’ to ‘brown’???
hey..i had a small problem..
i wan to make the .res file..but..
it does not show off when i drag and drop at the mkrest2…
any1 know..
can i skip the res file coz it does not generated??if can the how can i proceed??my phone is R8BC004..
k770i cid53
hi akshayy the best site you have
this is my first time writing to you i learned flashing my k800i from ur tutorials they r best and very easy my phone is k800i cid 53 color red i wanted to apply patches toy phone i followed ur tutorials and after uploading the three files and running executor in games and then in the next step i am getting this error when i connect it using script qa2020
“Open Pluging(connecttophone(getcid(cant find device info in xml [53red])))
i have k800i and when i try to open bfs file my phone turns on.why?