You try to start your phone but the red light at the infrared port blinks 5 times and phone refuses to start. XS++ and SeTool 2 lite no longer detect your phone. Your computer also does not identify your phone. ANd its seems to be completely Dead..Read On, We will fix it.
Redlight blinking is a Sign of Low Battery or a Dead EROM. Some time during flashing the EROM goes dead or corrupt due to errors. If phone has a bad EROM it shuts down and does not start even if battery is charged to full.
Double Check that battery is not the problem before you proceed to flash the EROM.
In that case we have to repair the EROM. And now here we will discuss the easiest way to fix it.
Note: Before you use SeTool 2 lite you will need to have USB flash drivers installed. If you are visiting this website for the 1st time its highly likely that you do not have the USB Flash drivers installed. Please follow the USB flash driver installation tutorial in tutorials section to install them. And kindly borrow your friend’s Sony Ericsson Phone to install usb drivers because your phone is dead.
Using SeTool2 lite 1.11 we can fix this problem by this way.
- Start SeTool 2 lite
- Press Unlock\Repair Button, The first button.
- Reinsert Battery
- Connect phone holding 2+5
- Wait, SeTool 2 lite will repair the EROM, it will flash it back.
- Done
Now you can start your phone.
Regards Akshay.
Hi Aks,
This happened to my wife Z610i… Red light blinking and xs++, Far and SEtoollite can’t detect… apparently after leaving it overnight the phone just work when we tried it in the morning… don’t know what happened but its working now…
hey man .. redlight blinks even if battery is zero
when battery falls below 5% it starts off to blink in all SE Phones .. i think that was the case with your phone .. with such low battery u can’t connect phone to xs++
Its not the battery… because I even tried my k550 battery (80% full) in my wife z610 phone… it still won’t work… her battery that time was 60%full… k550 & Z610 has same battery BST-33… I even tried her battery on my phone and it’s working… thats why I’m very confused… and when her phone boot up in the morning it created a loud single beep… I don’t really understand what happened…
Hi akshay i m new to sony ericssion modding. I have k 790i and i want to know how i patch mega bass to my phone. To patch my phone i need to unlock it or not. Give me detailed informations. How i take the backup of my firmware if anythings goes wrong i have the backup. I m new to sony but i know everything about motorola. So please help me from where should i start modding my phone. Thanks
^^^
ok . start from dis tutorial
http://www.akshayy.com/sonyericsson/tutorials/customize-your-phone/
ur k790i is a db2020 phone , hence it shud b unlocked.
download ur main (.mbn) file & fs (.fbn) file matchin
ur frimware. after xtractin ur fs , u can have a backup of all d orignal files.
go to the applying patches tutorial
all detailed info. is given der.
these video tutorials will help u to patch
http://www.4shared.com/file/36652928/3b29c575/patching_video_tutorials.html
hi akshay again i wanna need a skin that comes in w850i in which the menu icon is animated or moveable how can i do that to my phone also
Martin .. why did you this this EROM Flash ??
i mean Unlock\Repair
its to be done only if your phone was dead
!!
now try to repair it again .. charge battery max
there is no other way out of this problem
rakesh joshi
hey man download all flash menus from my downlod page .. and install them using FAR manager or XS++ .. see the tutorial for them
Martin you need to HOLD C and connect phone to Computer .. not 2+5
you connect with 2+5 only when phone is dead
I have a Sony Ericsson S500 and i am getting the red LED flashing. I tried the 2+5 method using SEtool, but it didn’t rectify the issue. Akshay can you help me sort this problem?
THanks!
and why did that happen in first place ?
i hope your battery was full !!
yes it was full, but i believe that the wrong S500 GDFS flile was loaded onto the handset. Phones are not a porblem but is there a way to recticfy this problem.
P.S
You have some nice tutorials here on the page
heyy ! if you wrote wrong gdfs then phone is dead completely .. if you can write back original gdfs then fine.
may be you can try out writing back original
but you might need service cable . and that too no gurantee of fix
okay thanks for the info. nice new look and all. lookin forward for some other stuff from you guys.
hi akshay… my boyfriend was downloading some themes from my computer to his and then sudenly it went blank.. it froze up. we took the battery out and change it with his mother’s one which was full on. it didn’t work.. only a red light flashes on the right side .. do you thing what you say we should do works even if we weren’t flashing it??
🙁 🙁 helpp
hey !
i have no idea what happened to your phone !
Its mostly a case of dead battery or dead battery circuitry inside the phone !
Or Try connecting your phone to XS++ ! if it does then fine ! if it does not then EROM is dead ! very sad ! EROM is very though to fix ! Sony Ericsson Service Center Replaces your phone for FREE if your phone is in warranty !
now we need to know technical details of your phone .. you have not even mentioned phone name !
First install USB Flash drivers, then connect phone to XS++ holding C, if it connects then fine
else connecting using 2+5 and see what it says ! if its getting detected in 2+5 then is bad EROM !
and we can try to fix it with SeTool 2 lite !
Please Install SEUS update service ! or install drivers manually !
http://forums.se-nse.net/index.php?showtopic=17540
LOL ! you got my name correct !
jajaj yeshhh sorry.. it was a w580i ericsson.. but no problem my bf change it recently but the company had no idea what happen.. u know what was strange is that red light blinking.. nd i know it wasnt the battery.. very odd i hope its not something common because im going to get one, too.. so thanks for your help akshayyy} you rock!! 😀 ..
o and by the way.. what do you get when you flash the phone.. i want to do it but im scared it could damage the phone and then not get the warranty or something
check out this site
http://walkmans.wordpress.com
they provide content
and we provide methods to install that content 😉
check out the amazing flash menus ! amazing icons ! completely customization ! more walkman skins ! etc are few examples !
http://www.youtube.com/watch?v=qRtzrVT5Xbo
flashing or unlocking.. a lil confused :$
omgggg that video is amazing!! do you have to flash it in order to make it do that??
Depends on the phone. If you have a Walkman mobile or your phone supports flash menus, swf files, then you don’t have to reflash it. You just have to upload the swf and thm files to the phone. Otherwise you will have to do a crossflash… but w580 is a walkman model, so it’s just uploading files then.
that’s flashing, customization not unlocking !
you will be use FAR manager or XS++ to customize your phone… to change the way it looks !
and for Sysgrafix you use Setool 2 lite or JD flasher to apply patch !
Sys Gfx is changing phone’s graphics by directly replacing pictures in phone’s firmware with own pictures ! like changing radio skin, or any graphic non – text object..!
But is more complicated, and also the phone can get into need of reflashing. (own experience.. 😀 )
akshayy..help me, i’ve flash EROM K750i CID 36 BROWN to RED using FAR, flash are success,but now the phone can’t be turn on? I try to connect using XS++3.1, SETool2Lite1.11, FAR but it doesn’t detected. What shuld i do? Help me i’m very worry n confiouse..
Thx in advance…
akshay…. i try to rebrand my SEK750i to w800i, and im failed, my phone is dead too, but there is no red light. please help me to revive
Why not tell what happened? What XS++ wrote…
Akshay I tried connecting the USB while holding 2+5 but SeTool 2 lite still can’t recognize my phone for some reason. Please help, this is the third W580i I’ve had that’s gone wrong. I really don’t want to go through the process of sending it back in again…
how did your phone get to this terrible state anyway ?
install USB Flash drivers… or install SEUS, sony ericsson update service…!
and what does 3rd w580 gone wrong means ?
i hope it does not mean you already killed 2 two w580s !
you should click repair and then connect phone holding 2+5 !
am sorry for you… you should have report long back !!
you get immediate reply here usually when i don’t have exams at college…
i think you better get your phone replaced and don’t touch it again ! or take the help of your friend to get the job done… whatever it is .. debranding or unlocking
hi… thx alt for the service man..
gues i successfully flashed my k530 to w660.. tho i do not feel the vibrations when scrolling through the main menu.. s it not supported in this fone???
and when i connected the fone and tried using SE disc to phone sw,
it says insert memory stick or connect via usb..(when it is already connected)//
please giv a solution soon.. do i have to install the w660 phone drivers on my pc??
thx alt..
isuru
Not all menus vibrate, some don’t. You have to reinstall drivers, because the phone changes its name when you flash it.
Why do you use Disc 2 Phone anyway? 😉
Thanks Akshay! I must sound really pathetic but thank you soo much!!
hi akshay, do you have a tutorial in flashing EROM? and also what tool to use.
Thanks
hi akshay,
my k800 is dead and im trying to fix it using xs++. unfortunately, i cant make xs++ work. when i connect my fone it stops here:
08:32:08| XS++ v3.1 (Darwin) Ready !
08:32:08| Executed on Microsoft Windows XP
08:32:27|
08:32:27| Attempting to open the interface…
08:32:27|
08:32:27| TURN OFF PHONE!
08:32:27| Hold ‘C’ button on phone and connect phone NOW.
08:32:27| You have 30 seconds…
08:32:27|
08:32:33| Baseband ID: 9900
08:32:33| Protocol Version: 3.1
after this nothing happens. what could be the problem?
hope you could help me
This tutorial is about flashing… fixing the EROM, we have no other tutorial about it. Is the red light blinking?
yes peti, i have the dreaded red light blinking. do you know any tool that i could use beside wotan, davinci or kulankendi. is there any tool that is free? all of this tool has a price.
SeTool 2 Lite is free.. I don’t know any other. 😛
i think that i have
1 bad erom (red light flashing/dead)
2 GDFS is corrupt ( YES, i have backup)
but when i try to fix erom following above guide it gets to a point where it says loader startup:executed “executing CS loader GDFS startup…”
and will not proceed past this point.
Same with GDFS.
heres a screenshot –
http://i109.photobucket.com/albums/n74/timwood_2006/untitled-1.jpg
that sucks
you try to reflash main and fs
then do a gdfs write of backup
it wont flash. it gets halfway through and then play the disconnecting noise and then fails in the program.
any help?
i know my phones fixable cause earlier i did something and i managed to flash it and have it working at W580. but, it was locked to a network so while using the guide to unlocking something screwed up while flashing with the patch and its back to the start again.
if i cant fix it ill just sony service center it cuase its $50 if its a software problem.
cheers
Is the battery full?
fixed it. it was the battery lol.
thank god i left it charging all day.
cheers for the help.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35923501618448 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:97 secs.
Elapsed:97 secs.
Can you help me i get this message 🙁
The reason i killed my mobile is when i tryed to put the Swedish language then i deleted the other except english then in the beginning when it says ”do you want to set the time and date” then i pressed cancel then it lag then i took the battery out after that i get that red blink 🙁 pls help me
lol i forgot i had the Phone Type at K350 but when i choose w580i then i do it the loading bar stop for awhile then it continue again but its not detecting my phone 🙁
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35923501618448 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs.
Now i get this 🙁
Hi Akshay. My computer won’t detect my k610 phone when i plug in the phone’s data cable. Is it possible when power off? Here is my problem scenario… My k610 won’t turn on, just series of blinking infrared lights, totally black screen, no flash, won’t charge the battery as well. Need urgent help. Please post the solution or email me. Thanks in advance.
hii ! so EROM is dead
repair it using above tutorial
i hope USB Flash drivers are installed
if not sorry there is no way
is there som hope for my mobile ?
CSloader refused to start GDFS services,error is:29
failed, that is fatal
it is compeletly dead ? :/
Where do i get GDFS cause i have same problem as Tim and i dont have backup 🙁
A guy posted a tutorial about it, there’s always hope. 😀 Though I can’t find it, it was a mail. :S
ah ok i must really fix my mobile its my mothers i borrowed it from her she is on vacation now and shes coming home on about 1 week i dont tell her about that yet so please help me to fix the problem :/
Ok I will try again. What do you mean reinsert the battery in step 3? Do I have to fully charge the battery and insert it back to the phone?
hope you guys have battery full…!
also jasper it does matter even if you choose phone as w580 … it should work fine
because w580 and k610 are of same platform
forget it .. i don’t know any method to fix phone if gdfs is gone
atleast for free… though there is a paid method with SeTool 2 Full .. if i remember
Jasper you try to do a full reflash of FS and Main
RD yes .. battery full, reinsert battery
How do u full reflash of FS and Main RD ? btw if my phone is dead and i put the charger do the battery charging then or do i need other SE phone to charge the battery ?
Thanks… my w580 died, and the program worked like a charm!! thanks soo much!!
drizzle .. are you being sarcastic ? or did you just recover a dead phone with this tutorial ??
Hi Akshay. I don’t know whats wrong with my k610. It run out of power the other day then it would not turn on anymore. Series of blinking infrared on top of the phone and a black screen, that’s all i see. I don’t know if it’s the battery or erom problem. I tried to connect my phone in x++ but won’t detect my phone. It shows this message
Error: Cannot open phone communication port
then its battery problem
recharge it maximum
for XS++ to detect phone USB Flash drivers must be installed.
and it does not detected Dead EROM phones.
it can detected them only in 2+5 boot mode.
Hey Akshay. I brought my dead sony k610 to cellphone repair store today. Battery works. The technician said it has to be reprogram or reformat. Do you know how they do it? Could you tell me. Please help. Thanks in advance. You’re a mobile genius/savvy/geek.
no idea… let them try..! if they fix it then great!
i doubt.. if gdfs is gone.. they won’t be able to
i hope you are lucky !! its EROM was gone.. if red light blinks
akshay, i can’t get this to work. does sim card and memory stick has to be removed when repairing erom? when i run setool2, press unlock/repair, then reinsert battery, then hold 2+5 and plug in my k610 data cable, it just flash a red light again. How long i have to hold 2+5?
i read many forums on the web. people suggest wanton client, kulankendi, cruiser, etc. but they are paid version i think. and not sure if they really works. =(
it will detect it if connect phone holding 2+5
if its still not getting in then battery is not full
in setool, the default phone type is k310. mine is k610 so i select it. then two check box comes up. first is bypass db2020 security. second is use “quick access” path. what check box need to be tick?
no you don’t have to check any options
its not even mentioned here. choose phone as k610
Hey akshay, i turned my mobile SE W580i off, now can’t switch it on, there is just a red light blinking…….Plz help, what do i need to do?
battery is low… recharge it !! EROM won’t die just like that.
well, i tried but there is no sign of it getting charged! and still cant turn it on!
some how get it recharged and try connecting your phone to SeTool 2 lite holding C…! or XS++
to install usb flash drivers you need to connect phone holding 2+5 and then connect it
better goto service center. they will give you new phone. because you are new here you won’t be able to install usb drivers and then repair it using setool 2 lite.
but here is tutorial.
remember you need to connect holding 2+5 during install not C as the tutorial was written for normal working phones.
http://www.akshayy.com/sonyericsson/tutorials/installing-usb-flash-drivers/
then repair using setool2 lite
thanks………for the help!
hi akshay! i tried to recover my dead k800i using your method. but it says an error
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35342701383918 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:4 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35342701383918 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:8 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35342701383918 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:11 secs.
what could be the problem?
You updated to CID 53 with SEUS?!!
CID53 ? that sucks
no support for that
can i downgrade it using setool or any tool?
CID downgrading is not possible. I think it just may work if you had an old GDFS backup, but I’m not sure if it can be restored. :S
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100033182 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:6 secs.
SEw580 is the model
I’m getting the following error could you kindly help me on this
hi akshay owndered if you could help
i tried putting a theme on my phone ages ago and it went dead so its just been sat in the draw using all your methods i managed to get the phone back but now it all lites up and says please wait the bar goes half way across then stops thats it .been like it for hours . i dont want to update using seus incase it updates to cid 53 here is what it says in xs++ oh also in setool lite the repair/fix at the top is greyed out and i cant click it many thanks mike
23:26:33| Sending db2010_cid00_prodid_p3l.bin…
23:26:33| Applet ID: 061113 1250 ALUCXC125872_COMPACTPRODUCTION_ID_LOADER P3L
23:26:33| This is a PRODUCTION_ID loader
23:26:33| Activating GDFS…
23:26:34| Phone name detected!
23:26:34|
23:26:34| Profiling SEMC phone…
23:26:34| Platform: DB2010
23:26:34| OTP CID: 49
23:26:34| EROM CID: 49
23:26:34| EROM Color: Red
23:26:34| IMEI: 35233601xxxxxx
23:26:34| Phone ID: W810
23:26:34| Region: S_ASIA_LEVAN
23:26:34| CDA: CDA102555/110 R2A
23:26:34| Firmware Version: R4CE012
23:26:34| EROM: n/a
23:26:34| Ready for operation!
mike now you just reflash main and fs and cda
that’s all using XS++ follow debrandig/ flashing tutorial
all will be ok
Sri reflash fs and main and cda.
dear akshay i have a w610 its dead due to flashing got checked it 4rm locals and they say that the fone is dead and wont repair but the red light blinks!!
i flashed the fone b4 when it was ok several times due to downloading of chinese firmware but know its been a monyh or so and my phones laying down doing nothing!
i downloaded setoollite1.11 but when i press the unlock/repair button the software closes suddenly!
i have already downloadded it thrice please help!!!
p.s ur site roxxx
windows vista ? try in XP
install usb drivers.
its problem of your computer
your problem can be fixed easily with this
Try on other computer.
Get some other SE phone .. then use it to install usb flash drivers.
use setool 2 lite to repair your dead phone
My phone is dead and flashing red lite. The battery is fully charged. I think there is a problem with Erom when i tried the steps on your site it showed me the above error. Could kindly let me know how to reflash the memory
hi i have try to access my phone w700i with XS++ 3
it has all gone well
10:08:05| Baseband ID: 8040
10:08:05| DB2010 Marita compact
10:08:05| Protocol Version: 3.1
10:08:05|
10:08:05| Sending db2010_cid00_prodid_p3l.bin…
10:08:05| Applet ID: 061113 1250 ALUCXC125872_COMPACTPRODUCTION_ID_LOADER P3L
10:08:05| This is a PRODUCTION_ID loader
10:08:05| Activating GDFS…
10:08:05| Phone name detected!
10:08:05|
10:08:05| Profiling SEMC phone…
10:08:05| Baseband ID: DB2010
10:08:05| OTP CID: 49
10:08:05| EROM CID: 49
10:08:05| EROM Color: Red
10:08:05| IMEI: 35167401xxxxxx
10:08:05| Phone ID: W700
10:08:05| Network: TAIWAN
10:08:05| CDA: CDA102663/23 R2A
10:08:05| Firmware Version: R1CA021
10:08:05| EROM: n/a
10:08:05| Ready for operation!
Something like this after that when i try to start the phone it does not start at all
nikunj is your phone is ok
reinsert battery to start your phone dude
also if phone is not starting then Reflash main+fs+cda
see the flashing/debranding tutorial for xs++
Akshay the phone is deacting in XS++ but when i try to reinsert battery to start the phone nothing is happening
after flashing my phone every process went well but the end it showed me this n still my phone is not working
17:08:28| Sending db2010_cid49red_flash_r2b.bin…
17:08:28| Applet ID: 051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2B
17:08:28| This is a FLASH loader
17:08:28| Flashing breakinfirm\W700_R1CA021.bin
17:08:28| Header type: BABE
17:08:28| 2 flashblocks
17:08:28| Binary acknowledge failed with: 15
17:08:28| Failed
please help
I saw the same error when I tried to flash W800 CID 49 firmware on a CID 49 K750. Is the CID number of the phone correct?
hey Akshay need some help!!!!!!! my k800i is dead. its not even blinking da red light at da side!!
xs++ or setools is detecting the fone. what could be the problem???
this is da message i am getting when i connect my k800i to setools lite while pressing 2+5
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35170701751579 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:83 secs.
Elapsed:83 secs.
Did you try to reflash main (and FS and CDA)?-.-
hi
after this problem of before the problem????
After the phone couldn’t start and before connecting with 2+5.
hey
i tried to do that. but the software is not detecting the phone!
so is it still possible to do this??? if it is then how do i do it????
And you have drivers installed? Maybe a little extract from XS++ log would help.
yeah i have the drivers installed!
its says
21:37:26| XS++ v3.1 (Darwin) Ready !
21:37:26| Executed on Microsoft Windows XP
21:39:03|
21:39:03| Attempting to open the interface…
21:39:03|
21:39:03| TURN OFF PHONE!
21:39:03| Hold ‘C’ button on phone and connect phone NOW.
21:39:03| You have 30 seconds…
21:39:03|
21:39:35| Error: Cannot open phone communication port
21:39:37| Disconnected… Unplug the phone
i cant even get past identifying the phone! im getting lost around the 2+5 or pressing “C” area. please help.
ey ! no drivers installed or something. phone always connects in 2+5 if it not physically damaged. if phone is damaged by hardware then it can’t be fixed this way.
nap.. what exactly is the problem ?? XS++ can’t detect phone ? try connecting phone to XS++ holding 2+5 and let us know what happens.
if your red light is not blinking then its not EROM dead problem.. remeber that. buy you can stil try to repair it using this method.
hey akshay, i hav a k790i n i think da eron’s damaged.. nw i rem my batt was jus 14% full wen it happ, so i was wonderin if i could still recahrge da batt wiit da same piece or will hav hav 2 look 4 an alternative batt??
Why don’t you try doing so then? The worst thing that can happen, is that the red light will blink or it won’t charge the battery, but these can’t harm the phone at all.
heyy akshay….big prolm…plzz help me out…ma hands r shivrng…cuz…m in a big trouble!!!
using setool….i applied a patch….n nw….vneva i strt ma fon sony ericson’s sign cms…n gozz bak…n fon switches off!!plzzz help!!!m havn bakup of gdfs 2….i’d stored it using xs++…bt still n success…plzzz help me!!!!
dude that’s foolish. GDFS restore tutorial clearly says when to restore gdfs.
now just reflash fs/main/cda. that’s all
lol
see the xs++ flashing/debraing tutorial in tutorial section.
hey my batt is 86% full but wen i try doin da repair i still get an error which says “CSloader refused to strat GDFS services, error is :29” plz help….
n i tried charging da batt wit my dead fone, it doesnt wrk..
does your phone connect to XS++ ?
try to do a full reflash on main and fs using setool 2 lite in 2+5 mode only.
Thank you so much. You’ve saved me 20$ in order for the local service center to “repair” it.
🙂
hey i tried conn 2 xs++ but it stops processin after tis…
14:01:14| Hold ‘C’ button on phone and connect phone NOW.
14:01:14| You have 30 seconds…
14:01:14|
14:01:19| Baseband ID: 9900
14:01:19| Protocol Version: 3.1
and in setool it starts flashing da 460 blocks.. after if finishes i get a msg..
CSloader not responding, changing baudrate..
CSloader not responding at all, aorry…
can u tell me wats wrong??
n everytime i try flashing on setool i get diff errors.. lik tis time i gt
CSloader refused to start GDSF services… error is 29
Akshay please help me. My W810i died, it shut down on me, would start then shut down, white screen, now it starts and only shows theme background and no menu. What do you think is up with it. red light is not flashing, connects to xs++ ok db2010 erom cid49 firmware is R4DB005 Does it need flashing? what with ? I dont want to change anything on my phone just want it to work.
Yes, it needs flashing. Probably you only need to reflash FS. But I only found later Firmwares, so you reflash main, backup your contacts, reflash FS, upload a custpack.
http://sek750.extra.hu/letoltes/Firmware/W810/R4EA031/MAIN/W810_R4EA031_MAIN_GENERIC_HN_RED49.zip
http://sek750.extra.hu/letoltes/Firmware/W810/R4EA031/FS/W810_R4EA031_FS_EUROPE_2_RED49.rar
http://sek750.extra.hu/letoltes/Custom%20Files/W810/W810_CDA102555_2_Generic_Central_Europe.zip
(CENT_EUROPE stuff)
Well flashing FS formats the phone memory, better be careful with it. But I couldn’t find the main that would be compatible with your current FS, and they might be incompatible, so it is better to flash FS, too. But before doing so, you must backup your stuff, your CONTACTS!! with MyPhoneExplorer…
I suggest reading the K550 -> W610 crossflashing tutorial, because it writes a lot about flashing basics, and also there you can read more about the process (like taking out the battery 😉 ).
FAR Manager is not necessary, XS++ can also do the customizing, the third link. 😉
Thanks Peti im new to all this, So i can go into xs++ flash main firm ware with r4ea031 main generic hn red49 then flash flash file system with r4ea031 fs europe 2 red49 and then exit?? do i need to remove battery between flashes? do i need to go back in and do anything or is that it? So i dont have to go into far manager?? as part of this?
A flashing tutorial i read Said DONT FLASH YOUR FILESYSTEM AS IT WILL OVERWRITE EVERY THING. So do you say its ok to do this and i need to to fix this ???
Sorry first time im a little nervous
Stupid WordPress! Look one post above. 😉
hay.. today i have flushed a new filesystem and main… and after that i also wrote the gdfs (my own backup)on the phone. Now when i connect the phone to the pc the infra. light blinks 1 time.
nothing happens if i connect using ‘c’ but detects if using ‘2+5’ ..
Is my cell gone??? what should i do now?? plz help..
So why not follow this tutorial?
Probably SeTool will fix it. If not, you will have to take it to a service center….
YYYYYYYEEEEEEEESSSSSSSSSSS.. my k800i is now fine and working.. Still have a network lock on it.. but it can be fixed.. Thank Peti for the reply.. thanks a lot for the post…
YYYYYYYEEEEEEEESSSSSSSSSSSS
Hi peti, 1 more question before i flash my phone, im not worried about backing up my contacts, but in a tutorial on this site it says about backing up GDFS says i need to using X++ . My version is v1.2 and doesnt seem to have the back up gdfs function is this only availible in v2.0 and do i need to do this back up?
Thanks for yr help
Backing up GDFS is an optional step. I never needed my backup, but it is better to have one, because it can get damaged, and if you don’t have backup, your phone might be lost forever (bricked).
So create a backup!! Use XS++ 3.1, download from our other site.
Peti, downloaded xs++3.1 and backed up gdfs ok then flashed main and fs with downloads you supplied thanks again. But it had problems with customising i did as the tutorial on here said made up folder named it own_custpac and loaded yr cust pac into it but it said customising failed then flashing failed. Could i have just selected a cda from the list allready there? did i have to make my own cust pack? xs++ 3.1 wont reconise phone now comes up with this
sending db2010_cid00_prodid_p3l.bin
payload failed
sendingproduction__idloader
sending db2010_cid00_prodid_p3l.bin
Header failed
Activating GDFS
xs ++ v 1.2 seems to reconise phone but still probs in there too
Please help 🙁
XS++ 1.2.. isn’t that…..bad
which phone ??
USE XS++ 2.2….!! then reflash fs/main/cda all correctly.
phone will work all well.
W810i can i just select one of the cda s from the list on xs++ instead of selecting own cust pack?
thanks for yr help
It’s better to use own custpack. Download from seflashing.extra.hu. 😉
yes sure. choose any db2010 phone and select the custpack that matches your FS.
if you want only english language then choose any cda… but a db2010 phone cda.
Thanks for being patient with me.
Ran it again using main and fs peti sent me and selecting xs++ cda cda102555/10 europe 1 same cda as was on the phone before.
says customising failed and flashing failed
says
sending loaders\db2010_cid49red_cs_r5a.bin
failed sending header 0x10
loaders\db2010_cid49red_cs_r5a bin is missing
does this mean i have a file missing out of my downloads Its running R4DB005 firmware peti sent me R4EA031 main and fs to use on it
actually which version of XS++ you are using.
and which phone..?? tell me all that.
as i told USE XS++ 2.2 or else it won’t work
Sorry w810i just tried it using xs++v1.2 will download v2.2 and try that thanks
connected to xs++ v2.2
Says sending db2010_cid00_prodid_p31.bin
Prologue failed
will not connect with phone
tried 10 times it finally let me in and i was able to carry out flahing again with xs++ 2.2
Still failed
said
Sending loaders db2010_cid49red_cs_r5a.bin
seems to fail when its in the customising process
Is it just the cda causing the proplems
What is the bin file it keeps refering to and having problems with
or is it that cda102555/10 europe1 cannot be used with R4EA031 this phone is enough to drive any one crazy
Or is the problem that i cant write R4EA031 main and fs over the top of R4DB005
Has any one got links to R4DB005 main and fs
It can’t be the problem. I have only R4C and R4E main & fs. Maybe the custpack is wrong…
ive tried using the cda s that are in xs++ and tried selecting cda102555/10
then cda102555_2 none seem to work maybe the ones in xs++ dont have enough info maybe i need to select the cust pac but that didnt work last time either
Stuart……!! So you have a w810.
Using XS++ 3.1 !! Try to Reflash Main + FS …!! Then try customization.
if that does not work…. then try to repair EROM using this tutorial.
then go for a full reflash of main+FS+cda.
that should work fine now.
xs++ 3.1 wont reconise the phone came up with Sending db2010_cid00_prodid_p3l.bin and thats it wont connect. I did try xs++2.2 and it did manage to connect after a while then flashed just main and fs but came up with . sorry yr phone is not supported cannot send flash loader flashing failed
Then did as u asked setool lite 1.11 pressed repair unlock then connected ph with c button in
said loader header not accepted cant load id loader and stoped
Thanks again for yr help Akshay this phone really is testing us ummm any other ideas
okay, um my w580 was doing the red blinking and, I followed the tutorial. After the program did its do. It tells that every thing is good but at the end CSloader refused to start GDFS services
So what should I do Now
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35714301225999 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:29 secs.
Mike. in 2+5 mode you reflash main+fs.
god only knows why your phone went into this Red light state…. i hope its EROM dead and not something else really
Stuart… man your phone is refusing by all means.
now only try is SeTool 2 lite.
flash the main fs and cda with it.
there will be a big empty box in setool 2 lite.
put the mbn fbn and hit flash .
then again you add to zip the cda files and then put in that empty box and hit flash. hope setool 2 lite fixes your phone.
actually you can use Setool 2 lite also to debrand/flash etc.
So like wat do i do akshay
tried on se tool to flash main and fs
no good either
loader payload not accepted
preboot failed
Recovery needed
Whats a recovery on a phone done them lots on pcs
hey MIKE.. i will mail you in 5-6 days.
just google search repair db2020 corrupt gdfs. you should fine a tutorial .. till then
I love u… thank you!!! You save my phone…
setool is a virus. it contains a trojan called generic.
dont use it.
and ive tried every unblocking tool and i still cant unbrick my freinds k800
Ok i’ll keep on the look out
DAN…. that’s silly… i can’t help your stupid anti virus.
SeTool 2 lite has nothing to do with your computer dude…
hey 🙂
suddenly my sony ericsson s500i wont turn on.
when i try it vibrates once and thats all.
i put the charger in as well but nothing works.
i dont know what to do?
please help.
x
@ dan: SeTool is recognized as Trojan Generic (by NOD32), but generic means that it has no name, like the trojan in it is not recognizable, it is only, that it has some functions that could harm a pc, but it can’t understand how… Besides you can download it from any site, it will be infected (or considered infected by NOD32), and many flashers still use it, we never haved problems with it….
@ Olivia: If you still have warranty, then bring it to a SE service center. If you don’t, remove M2 and SIM cards from it, backup GDFS, and reflash Main and FS, and upload a custpack… This (almost) always helps. 😉 (You will lose contacts and files on the phone…)
hah thanks so much for your help.
but im 14 and i dont understand.
whas M2 and whats backup GDFS and reflash Main and FS?
haha so sorry, just i dont really understand.
thankyou 🙂
it just wont charge and it flashes 5 times.
14.. lol dude that’s a lame answer.
you get your phone replaced from sony ericsson then.
they will happily give you a new S500i
if the red light flashes 5 times. then EROM Is dead.
install usbflash drivers using another SE phone.
repair phone using this red light tutorial..
later follow other tutorials at site…
best for your is to get phone replaced if you don’t like technical stuff.
hah it isnt a lame answer!
but cant i just download setool thing?
x
14 is a lame answer, I’m 15, and check out the forum thing…
Though Olivia is a girl name and then it is understandable. xD
Download it and follow the tutorial…
aaaah what forum thing?
haha i agree, girls arent made for these things.
do you have msn or something so you can like explain to me:)?
x
Akshay’s msn is [email protected] , I’m a bit busy right now… 😛
thanks:)
so like what forum thing do i have to download?
or can i download the setool thing?
x thankyou your a great help.
(L)
and dude like everytime i download setool it crashes..
what crashes ?
setool 2 lite you can download from any where on the internet.. just google search
here is out download link
http://seflashing.extra.hu/?mode=dlSoft&name=SeTool2v111.rar&show=fileinfo
why does it crash ?? 🙁
that’s bad.
windows vista ?
also how will you use SeTool 2 lite ..
usb flash drivers are not installed. and to install them you need a phone that is alive.. dead phone won’t do..
but you try the whole USB Driver installation tutoral…
but in all cases hold 2+5 instead of holding C ok..?
in tutorial it says hold C but you hold 2+5 and connect.. here is the usb flash drivers installation.
http://www.akshayy.com/sonyericsson/tutorials/installing-usb-flash-drivers/
Olivia i know that you were trying to gooogle search this
sony ericsson has one red light on the right side?
and you ended up here again at this site… lol
akshay you HAVE to help me! 🙁
right.
the phone is blank. black screen.
i took out my battery and put it back in.
then tried to turn my phone on, and it just vibrated once.
but i put in my charger and it has a red light.
but then sometimes it flashes 5 times.
what the hell do i do:(?
please help..
thankyo so much for being patient.. xx
Peti hi still battling with my w810i have flashed main and fs with ones you gave me ok then went back in to customise with cust pack but had a job reconising phone had to connect and dissconect lots of times before it worked . and No i didnt start up phone inbetween the two.
still not working starts with white screen then goes black and flashes white once or twice and then turns off. do you think i should try the original cda instead of one u supplied me? could this be the problem ?? does not flash red light so erom must be ok ??
hey stuart… CDA has nothing in it.
its only to setup languages in phone.. so relax.
it does not affect phone in anyway.
try to repair EROM using this tutorial and then go in for flashing again.
i really really don’t know what’s wrong with your phone.. 🙁
The same happened to me on a K750@W800. Without any reason, and then I took the memory stick out and… it was that, then it started working again…
Thanks Akshay will try erom again last time i tried using se tool it didnt want to reconise phone.
Peti the memory stick was the first thing i removed saw that prob in friends ph but only affected accessing photos etc nothing like this.
It crashed while i was sending a text which seems more like erom/ hardware problem cant see how software could suddenly be corupted like that. thanks guys easier to work out prob with 3 heads rather than one .
Akshay this is what happens when i click on unlock repair as per yr erom repair guide
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
FlashID check:897E
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35233601844550 CERT:RED
FLASHCID:49 COLOR RED
Model:W810i
MAPP CXC article: R4EA031 prg CXC1250316_GENERIC_HN
MAPP CXC version R4EA031
Language Package: HONG_KONG
CDA article CDA102555/10
CDA version: R8A
Default article cxc1250324
Default version R4DB005
Operator: 000-00
USERCODE:0000
RESTORATION FILE NOT PRESENT
“R4EA031_CXC1250316_GENERIC_HN”
YOU MUST PERFORM FULL FLASHING FOR PATCH UNLOCK
REST File is not present.
download firmware and in the REST folder in Setool 2lite folder create a rest file for that firmware using makerest or some program like that given in REST folder.
I have the rest file here can i just go into xs++ and select it in the main firm box then click flash?? Its not going to overwrite the whole main i just flashed will it????
no it won’t…!! its ok..!
And reflashing main also fixes the issue…
hi! my sony k610i died on me while i was text messaging. then i couldnt seem to turn it on. now, all that is happening is that red blinking light. is there any way to open the phone? and get the contacts saved on the phone and pictures too? please advise 🙂 thank you very much!
Following this tutorial won’t delete any of them.
Hi Akshay and Peti..
I followed your tutorial and i got the following result. I have a red blinking light when i try to start the phone or when i try to charge it.
Please help me as i dont have any other phone to use
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35220801134432 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:37 secs.
did you press correct button ??
gdfs sartup is happening neat..
i don’t know really what’s the problem here..!!
btw how did you install usb flash drivers. ?
the usb flash was already installed when i unlocked the k790. but then i was trying to flash the wiht k800 one but there was no network, and i unfortunitly backed it up with wrong gdfs so i had gdfs mismatch. here is the result when i press identify with 2+5
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35220801134432 CERT:N/A
FLASH CID:52 COLOR:RED
IMEI MISMATCH ! GDFS IMEI:35220801277685
Model:K790i
Brand:Sony Ericsson
MAPP CXC article: R1CC003 prgCXC1250477_GENERIC_EV
MAPP CXC version: R1CC003
Language Package:S_ASIA_LEVAN
CDA article: CDA102568/110
CDA version: R4A
Default article: cxc1250491
Default version: R1CC003
Network LOCKED
Operator: 302-72
Elapsed:14 secs.
Hi guys! I went through top sony and se-nse forums + your brilliant website. And the question is: if the mobile is dead and no red light is blinking – does it mean it’s the hardware problem?
The situation is: I got a faulty S500 from ebay (clicked at the last moment – didn’t notice it’s faulty. YES, I am BLONDE!). I have some experience with flashing/debranding – I hoped that’s the software issue. However: xs++ does not recognize it (communication error), setool does not recognize it (even with 2+5), kulankendi does not reconize it. Is there anything else I can try???
And by the way – love this website, your simple and straight forward tutorials helped me with W580 / Z310 / W880 (I’m really unlucky with the mobiles this year).
Best regards 🙂
Blonde women usually have silly problems, but this one is tough…
If 2+5 doesn’t work, then I think nothing will. But I think it might be just that the battery went too low, it was not in use for a long while. If that is the case, then 2+5 should not work all right.
So first try to charge it somehow in another phone, becuase if the phone is dead, it probably doesn’t charge either, but I don’t know for sure…
PHONE Is Dead.
How can a person Install USB drivers with dead phone then ?
To Install USB drivers you need a Working Phone.
We can’t really say what’s the problem with phone until you connect your phone after installing USB flash drivers.
If phone is OK in hardware then it will get detected !
hi akshay,
i had the same problem as mike when i click the repair/unlock button and follow your instructions this came up
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35683401518786 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:22 secs.
i searched for repair db2020 corrupt gdfs on google like you said and tried to follow the tutorials but some errors came up when i tried to write the gdfs! Please can you help me.
go for a reflash of Main + FS and then do it once again.
flash all using 2+5 using SeTool 2 lite.
sorry how do i reflash the main and fs?? thanks
Dear boys… I charged the battery (actually two batteries – W580 has the same one) for a whole night before trying xs++ and SEtool.
I believe it is a hardware issue – thanks for the confirmation though 🙂
Keep up the good work 🙂
@kiki: you start xs++, connect, tick flash main, and flash FS, and customize filesystem. Browse the appropriate files there. Use own_custpack method for customizing, download what you need from seflashing.extra.hu
Hello Akshay
I enjoy reading you page on sony ericsson flashing…i have recently bought a K550i but have not flashed it yet, i was hoping to do at some point howver..
Anyways this morning i woke up and when i turned my phone on, it was all white screen…itried to take the battery in and out and only got sum vibrations when it started, it was also vibrating when a call was recieved.
I have the SE suite installed with all the drivers but when i ran SEUS and followed directions (holding c while plugging it in) nothin happened. and after i download Xss program, it said check connection or unable to make a connection and didnt work….
What should i do? I am using a different laptop now with no drivers and i am running SEUS to install them, what should i do next to get my phone to work?
I think updating the firmware should restore it but what do u recommend?
Thanks
Bashar
Hi
I have a k800 that flashes a white screen when I try to turn it on and some times the infrared light blinks. Tried to fix my EROM using your guide and this is the log I got;
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35342701186106 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed:25 secs.
but the problem is my phone is still not working, and I charged the phone for a longtime before flashing it. But when i input the charger the screen goes white so im not sure if it’s even charging the battery. Is there something else I can do? Like flashing the Main and FS?
hi akshay i’ve changed erom chipset on k810i and flashing Main & FS but my phone doesn’t start and blinking white screen .
SEUS changes it to CID 53, bad idea. If it’s new, you have warranty, you better use that.
It is not likely, that you have dead erom and no red light, but still it would be worth a try to follow this tutorial, if XS++ can’t handle it.
If SEUS could finish, you already have CID 53, so you can only use JDFlasher to reflash main and FS.
@Robert: use XS++ to reflash main and FS, take out memory stick. Of course only if xs detects it.
@farhood: can xs++ detect it?
21:55:46| XS++ v3.1 (Darwin) Ready !
21:55:47| Executed on Microsoft Windows XP
21:55:51|
21:55:51| Attempting to open the interface…
21:55:51|
21:55:51| TURN OFF PHONE!
21:55:51| Hold ‘C’ button on phone and connect phone NOW.
21:55:51| You have 30 seconds…
21:55:51|
21:55:51| Baseband ID: 9900
21:55:51| Protocol Version: 3.1
21:55:52| Phone name detected!
21:55:52|
21:55:52| Profiling SEMC phone…
21:55:52| Platform: DB2020
21:55:52| OTP CID: 51
21:55:52| EROM CID: 53
21:55:52| EROM Color: Red
21:55:52| IMEI: 35928501xxxxxx
21:55:52| Phone ID: W580
21:55:52| Region: S_ASIA_LEVAN
21:55:52| CDA: CDA102774/66 R4A
21:55:52| Firmware Version: R8BE001
21:55:52| EROM: R3A022
21:55:52| Ready for operation!
21:55:56| After making any changes with FSX
21:55:56| you must press the ‘Shutdown’ button
21:56:02| Sorry, your phone is NOT SUPPORTED
21:56:02| Error: FSX failed.
21:56:02| FSX Shutdown!
21:56:04| Disconnected… Unplug the phone
plzzz help me!!!
what’s your problem Buvan
Its CID53 so you can’t use XS++.. use Jdflasher.
your phone is working why are you here at the dead phones zone……do you want your phone dead or what ?
someone please help me
@Peti:
Thank you very much, worked like a charm after I flashed Custompack aswell 🙂
I am using SE w880i , Some how my phone is dead & Red light is blink quite several times. I checked the battery its ok. But I think so it is something else.
I figure out tha its a erom issue. so Install xs 3.1
and downloaded the actual erom , I flash it but massage is showing that its still sending the erom to my phone . I am waiting since 2 hours.
Can you tell me how much time it will take to flash.
:36:50| You have 30 seconds…
02:36:50|
02:36:50| Baseband ID: 9900
02:36:50| Protocol Version: 3.1
02:36:50| Phone name detected!
02:36:50|
02:36:50| Profiling SEMC phone…
02:36:50| Platform: DB2020
02:36:50| OTP CID: 51
02:36:50| EROM CID: 52
02:36:50| EROM Color: Red
02:36:50| IMEI: 35777401xxxxxx
02:36:50| Phone ID: W880
02:36:50| Region: M_EAST_N_AFR
02:36:50| CDA: CDA102568/6 R8A
02:36:50| Firmware Version: R6BC002
02:36:50| EROM: R3A022
02:36:50| Ready for operation!
02:41:14|
02:41:14| Sending db2020_cid01_prodid_p3j.bin…:36:50| You have 30 seconds…
02:36:50|
02:36:50| Baseband ID: 9900
02:36:50| Protocol Version: 3.1
02:36:50| Phone name detected!
02:36:50|
02:36:50| Profiling SEMC phone…
02:36:50| Platform: DB2020
02:36:50| OTP CID: 51
02:36:50| EROM CID: 52
02:36:50| EROM Color: Red
02:36:50| IMEI: 35777401xxxxxx
02:36:50| Phone ID: W880
02:36:50| Region: M_EAST_N_AFR
02:36:50| CDA: CDA102568/6 R8A
02:36:50| Firmware Version: R6BC002
02:36:50| EROM: R3A022
02:36:50| Ready for operation!
02:41:14|
02:41:14| Sending db2020_cid01_prodid_p3j.bin…
Ahsen
dude your phone EROM is good and working
if EROM was bad XS++ can’t even open the phone port.
and if EROM is dead… repair with SeTool 2 lite… not XS++.
ok now recharge battery else where and try.
if that does not work then Repair EROM using SeTool 2 lite… it will fix it…!! follow this tutorial
Akshay,
My problem is exactly the problem “Red Light Blinking, Dead ?” that you have described. However, the SETool I downloaded from your site does not find my phone. So I am stuck at step 5.
I have the SE V630i.
Something I noticed when I charged it last night. The light atop the phone remains red. It never goes green.
Do you have any other suggestions? The phone is completely dead.
Regards,
T
It may be just that the DCU-60 cable is overused. It happened to me that I was trying to flash main and couldn’t because of bad cable, try to push it down, and move the connector.
hii…i tried flashing w700i…i thought everything is going in rightway….but after flashing and disconnected my fone frm XS++ v3.0beta……my fone is not turning on….its dead?…..
not even red light blinking frm infrared……..
heres one for the people who know what they are doing…iv tryd flashing the GDFS back, main, FS and the EROM using KKClient…the red light still flashes….
and fone still doesnt wana start….
for those of you that know setool 1.11 this is what i got when i tried to repair the EROM or click identify…
……………..Unlock/Repair……………….
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35243002795915 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:10 secs.
………………Indentify……………………..
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35243002795915 CERT:N/A
FLASH CID:52 COLOR:RED
Abort all operations.
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:52 secs.
please help…
thanx in advance
@sunny: I think you had ssw files but no rest files, so the restoration after FSX wasn’t done. It happens on DB2010… Just reflash Main.
@byron: can you backup GDFS of the phone now?
how to reflash main plzz help me in detail
You download the phone’s main from topse.ru/ mobilefree.ru/ seflashing.extra.hu/ seusers.com… Then unpack the archive to have a bin or mbn file.
Open XS++, Connect. Tick Flash main, browse the file. Click Flash. Wait.
sry…i am unable to understand the language…..plz help
can u send me the direct link plzzzzzz
01:31:56|
01:31:56| Attempting to open the interface…
01:31:56|
01:31:56| TURN OFF PHONE!
01:31:56| Hold ‘C’ button on phone and connect phone NOW.
01:31:56| You have 30 seconds…
01:31:56|
01:32:00| Baseband ID: 8040
01:32:00| DB2010 Marita compact
01:32:00| Protocol Version: 3.1
01:32:00|
01:32:00| Sending db2010_cid00_prodid_p3l.bin…
01:32:00| Applet ID: 061113 1250 ALUCXC125872_COMPACTPRODUCTION_ID_LOADER P3L
01:32:00| This is a PRODUCTION_ID loader
01:32:00| Activating GDFS…
01:32:00| Phone name detected!
01:32:00|
01:32:00| Profiling SEMC phone…
01:32:00| Baseband ID: DB2010
01:32:00| OTP CID: 49
01:32:00| EROM CID: 49
01:32:00| EROM Color: Red
01:32:00| IMEI: 35527101xxxxxx
01:32:00| Phone ID: W700
01:32:00| Network: EMEA_6
01:32:00| CDA: CDA102580/103 R1A
01:32:00| Firmware Version: R1CA021
01:32:00| EROM: n/a
01:32:00| Ready for operation!
this is the case wen i connect my fone
setool doesnt let me do anything anymore…and xs++ just reads my baseband ID and Protocal version….cant access any of the other settings on xs++
GDFS was backedup tho….tryed restor but doesnt work
setool doesnt let me read GDFS either
@sunny: use google translator. besides, seflashing.extra.hu is my place, english.
@byron: are you using 2+5? :O
yes
thats the only way my phone can connect to anything, if i use 2+5….if i use “C” nothing happens, doents read the phone at all
I have a strong feeling that it is now dead. But! it may be the battery. (Worth checking before throwing it away.) Also Akshay may know something.
Hi i have a W580 and tried to flash it but since then i have a red light flash on about 4 times a a bit of a vibration but it does not turn on i have tried flashing it about 6 times now with setool lite, XS++ and jdflasher. They all find my phone with just holding c and they all find the EROM do you have any suggestions please. Thank you for taking time to read
First try this tutorial. Second, check the battery, red light also means low batt. Third do you have a gdfs backup?
i have tried the battery, tried the tutorial and tried the gdfs backup i created but still nothing but the red light
Satcey.. leave it then…
Try to Repair the phone holding 2+5 ONLY using SeTool 2 lite…
but first of all you need to have a full battery to use SeTool 2 lite.
Recharge your battery using your FRIENDS phone.
If Red Light Blinks on and on then it means dead EROM.
That means phone is permanently damaged.. mean physically damaged EROM !
IF something is physically damaged replace it. Replace EROM = Replace PHONE.
Get phone replaced with a new phone. SE will replace your phone.
Why would they replace it? It had been flashed, means no warranty…
thanks for your help i will try with se
Hi i was using selite to fix problem with flashing red lights. Eventually i got it to work that my phone plays all souns like ringing tones and message….. But the problem is i have a white screen and i can see anything also when i try to charge it i get a red light and white screen on all the time. Any help would be great. Great site 😀
Jhon. That is terribly bad news.
Your battery is damaged or phone EROM is physically damaged/burnt/broken etc.
hope its the battery.
See what’s up with the phone and accordingly replace.
Peti. Warranty is valid as long as the service guy does not know.
when he comes to know then its up to him to cancel the warranty.
So I just flash K550 R8 and restore old gdfs backup and say I used seus… 😀 Nice.
hey…..my w580i is dead with red flashing light…i have no idea what to do..its fully charged…please help…i have no idea about all the technical terms explained above :s
Read the tutorial once more and follow it. Get SeTool 2 Lite from seflashing.extra.hu.
thanks…ill try it now 😀
hey..i tried the tutorial and i couldn’t do it :(…if my phones under warranty will the shop i bought it from be able to fix it for me? 😀
sorry to be a pain..but i have one more question …whats an EROM?
hey EROM is Erasable Read Only Memory.
Now Realizing that almost 99.99% of the people in world have not studied Introductory Computer Science in Junior Primary School. I thought computer course was famous…!! Sorry all then.
thanks :D:D:D:D:D:D:D:D:D:D
it makes sense now…lol 😀
my sony ericson w580i is not responding. the red light like you said is blinking 5 times. my battery is full. it has to be the EROM. i don’t know what to do. I don’t know what i have to do after i install the usb drivers inside my computer.
my computer does not recognize the phone at all. the screen does not appear. Please help me or send me an email
Thanks
Nauman
hello akshay
well i tried chargin my phone because battery was diein (but it wasnt completly dead) and i couldnt find reg wall charger so i decided to use my usb cable and hook up to my laptop…well when i connected it and closed out the boxes on comp and it started chargin all of a sudden screen went black but the buttons were still lit…i tried pressing buttons to see if phone would work but nothing was happening than i prob did something really stupid and took the usb cable off of the phone. after that screen was black and buttons still lit so i took the battery out and put it back in and thats when the red lite showed up. but it only blinks once and then nothing…please help if you can!! thank you
actually it does blink 5x sorry…also i tried hookin up phone to usb cable to comp again and nothing appears whatsoever on comp (asking for hook up of hardware etc) also tried holding down the c button and nothing…hope this makes sense and hope to hear from you soon…thank you!
@nauman: Get SeTool2 lite from our download server, seflashing.extra.hu
Then follow this tutorial, though it would be better for you to give it to a SE service center, if you have warranty. (You’ll lose it once you flashed.)
Sent in mail, too.
@kimnus: follow this tutorial.
kimmus…. your is clearly dead battery.
there is absoultey no power supply to phone. how can you expect phone to start…
phone won’t connect also. only if there is power in phone then only it can connect man !!
nauman … install usb drivers properly using some one elses phone. and if that phone connects to XS++ or SeTool 2 lite. Then USB is all ok
then recharge your battery using YOUR FRIENDS phone and repair the EROM.
thanks ill try chargin it…but i know i had battery power before i started chargin on the comp…i had about 4th battery life it said and battery level wasnt depleted…so if its not the battery charge than what could it be? thanks!
Wohhaaaaa, yehooow, it is worked on my brothers K610i locked with RED BLINKING LED.
Thanks friend I love you. YOu don’t need WOTANCLIENT.
Thanks
Thanks
Thanks
X)
akshay i charged the phone and tried turning it on and it did the same 5 blinking lights…so is it the erom? thanks
Should be.
I have installed the USB Flash Drivers and SE Tool 2 Lite and pressed Unlock/Repair and then connected my phone by holding down 2+5 and this is the error message that comes up:
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100204148 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:19 secs.
I would appreciate any help in resolving this problem. Thanks in advance.
How do I edit my previous post?
well in new wordpress even admins can’t edit comments
try again
and try reflashing main and fs and cda in this mode.
that is 2+5 mode.
I’m new to this so I apologize but can you provide me detailed step-by-step instructions on how to flash the main, fs, and cda?
Hi Akshay,
I’ve read through all of these comments several times and also tried just about everything I could find on Google.
I have a W580i originally from ATT. I debranded using SEtool2 lite, flashing the following files:
W580_CDA102568_7_R8A_GENERIC_C_ASIA.zip
W580_R8BA024_FS_C_ASIA_RED52.fbn
W580_R8BA024_MAIN_GENERIC_LA_RED52.mbn
Then I used FAR Manager with SEPF plugin to copy some theme files into the phone.
Everything was working fine for the entire first day. At night, the low battery alert came on, so I switched off my phone and then plugged it into the charger.
When I checked later, the phone would not power on (blinking red lights). Pushing C and connecting via USB didn’t work for SEtool2, XS++, nor FAR manager.
Luckily I tried holding 2+5 and it was detected by SEtool2. I tried reflashing the same three files (mentioned above), but it’s always ended with the infamous “CSloader refused to start GDFS services,error is:29” error after the flashing is finished.
——
I’ve tried XS++ using 2+5, which only goes as far as:
Baseband ID: 9900
Protocol Version: 3.1
and “Port opened ok!” in the bottom left corner of the window. Nothing else occurs after that.
—–
I’ve tried FAR Manager with SEPF plugin again, using 2+5, which actually now shows the entire file tree (before it was missing files). The files are probably back because I just did another flash with SEtool2 lite (three files mentioned above).
—–
I’ve tried every single solution I could get my hands on but to no avail. When I remove and then replace my battery, pushing the power button once will make the red LED blink once, pushing it a second time will make it blink five times.
I’ve also read that if there is no solution and if I were to send this into a service shop or to AT&T, I should write GDFS using an MP3 or junk file in order to corrupt the flash unit (so techs won’t find out about debranding).
Any help would be GREATLY appreciated. Please let me know if you require any additional information. Thanks.
Hi, I’d try flahs using 2+5, but SETOOL, XS++, Far, don’t read it. I has wrotten a GDFS from other W200 in my phone. Please. HELP!!!!!!
@Akshay: wrong. You can edit post, if I can… click the user’s name in comments section….
@Nitin: read the k550@w610 tutorial.
@Alvin: what a long post. Follow this tutorial to fix your erom. I wouldn’t mess with GDFS if I were you.
Thanks for the reply Peti.
I tried this tutorial at least five times already, and just tried it once more. The guy’s reasoning for messing up the GDFS was to create WSOD so techs won’t research it further. If I don’t corrupt it, I would think they’d instantly void my warranty due to debranding…
I’ve also tried SEtool lite 1.10 with “Bypass DB2020 security”, but it seems to infinitely loop after “Processing part3….”
EROM repair: I tried KulanKendi client, this tutorial, and WotanClient. KK didn’t seem to do a thing, as it finished in 0 seconds. Wotan won’t let me run it without a proper login.
This tutorial sounds like it’s worked for everyone else, but it hasn’t worked for me. Is everyone else restoring their old GDFS’s? because I didn’t back mine up.
don’t worry your warranty is valid ! because if phone does not start then they will never know it.
Yes everyone restores their own gdfs from their own phone.
did you write a alien gdfs by any chance ??
you can try repairing your phone using this tutorial
http://forums.se-nse.net/index.php?showtopic=27466
all the best.
Akshay, thanks for the prompt response.
I tried that GDFS fixing tutorial, but I get the “CSloader refused to start GDFS services,error is:29? error when trying to read GDFS in SEtool2 lite.
I have one last idea to try before I send it in, but would like to run it by you since you’re far more experienced.
One thing I haven’t tried is updating with SEUS (SE Update Service) using 2+5 (http://myforum.lasyk.net/showthread.php?t=38134). All the debranding threads I’ve read, say don’t update through the update service because my CID52 will turn into CID53, which means more trouble. But then again I’d rather have anything better than a brick right now.
I really admire you guys for helping all of us free of charge. It is very much appreciated.
no idea. then. but don’t try reading gdfs.
just directly goto write script. execute the gdfs read script to read security units.
i hope you did not do that writing of junk file to to gdfs .. in that case i think all the gdfs area is gone. and no way to repair that phone then.
debranding they will never get to know… so chill. because if red light blinks they just throw your phone in dustbin and send you new one.
Hi Akshay, bad news.
I tried skipping directly to the “Write SCRIPT” command using the given code (txt file) in that tutorial, but I’m still getting the “CSloader refused to start GDFS services,error is:29” error message.
No, I didn’t write the junk file to the GDFS.
The last solution I can think of is to try using SEUS, but I’ve read your other tutorial mentioning that SEUS will change me to CID53 (but can still be debranded/flashed with jdflasher?).
http://myforum.lasyk.net/showthread.php?t=38134
Any last suggestions?
hmm ok try that…..!! no other options.
hey akshay i tried to flash my friends w550i. But ultimately failed. Now only white light comes when i switch on my phone. Pls help fast. I need an online chat now.
YOGESH
well that sucks
for flashing w550 you need XS++ 2.2 actually.
its a exception.
now just reflash main and fs and cda with XS++ 2.2 that phone will be ok
sorry man tomorrow i have LAB EXAM. June 6th Morning…………
thanks man. u really helped me out.
Well then if SeTool 2 lite can’t repair it then even Woton will fail.
Now does the red light still blink ‘?
if red light is not blinking now and also if the phone connects to XS++ in holding C mode then reflash it and it will start.
i dont understand and im desperate for help!
when i hold down the on button on my w810i the white screen will just appear, also when i plug it into the charger the infrared port flashes, i dont understand what SeTool2 lite 1.11 is and how you get it, would this maybe solve my problem? please help!
hmmm … just rechage battery first.
some how do it.. or try to start phone with your friend’s w810 battery.
you should reinsert battery first.
and you should also have usb flash drivers installed.. which you can’t do with a dead phone…
hiya, ive recharged the battery but its still not working 🙁 dya think its dead for good, i mean it just happened randomly ? :s
not sure if the comment worked, i tried charging it didnt work, just when i hold down the on button screen is white, does it sound like its dead for good? :S i mean it just happened randomly
first of all you have installed USB flash drivers in your computer ??
http://www.akshayy.com/sonyericsson/tutorials/installing-usb-flash-drivers/
you can’t install usb flash drivers with a dead phone. use some other sony ericsson phone.
then after installing connect phone holding C to XS++ or Start SeTool 2 lite and click IDENTIFY button and then reinsert battery and connect phone to datacable holding C.
if it connects. then just reflash your phone using XS++
also try to connect phone holding C to XS++ and see what it says. and copy paste that here.
if its not connecting completely in holding C mode. then connect phone to SeTool 2 lite in 2+5 mode and repair.
If all this does not work then Its not a SOFTWARE problem. Its a hardware problem. In which case we are sorry we can’t help you replace your EROM or dead parts of your phone.
But its mostly that you are not doing things properly.. please try again carefully before you decide that your phone is really dead .
where do i get xs++ or the other one?
when i plug it in holding c nothing comes up to recognise the hardware?
Kayleigh why don’t you read what is said carefuly
i said you need other Sony Ericsson phone first to insall USB flash drivers.
then repair phone with SeTool 2 lite if you are lucky all will go well
I have read it carefully and i have done as it says. ok.
Hi akshayy,
my phone just stopped working..only red light blinking..tried to connect with xs++ holding c button did not work..tried SEtool holding 2+5..connected..but shows Can’t build loaders chain ;( message..tried to recover..sayz phone not supported..unlock/repair..same message…
XS++ detects phone..holding 2+5..shows Port opened!!..two lines.. Protocol Version: 3.1
does not proceed..please helpp!!
my phone is k790i
THanx for the reply Akshay,,I figured it out..I gave my phone for repair and the bugger changed the Flash CID from red 52 to 53..now is there anything i can do??
except patching you can do everything else
use JDflasher.
akshay…need your help bad pls! i installed the usb drivers and the SEtool2 i followed your directions and when i unlocked/repaired this is what showed?…
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100187010 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:31 secs.
phone wont turn on what can i do?! thanks!
CS Loader Refused to start service.
Does XS++ detect your phone ?
If it does then Reflash your phone.
then all will go right.
Flash the phone with SeTool 2 lite.
Connect holding 2+5
but use this guide and always connect holding 2+5 as i said instead of C.
http://www.seusers.com/forum/setool-lite-flashing-step-step-tutorial-26.html
if you mean when i plug the phone in and this appears on xs++ (Baseband ID: 9900
Protocol Version: 3.1)…then yes it does detect it but if thats not what its suppose to do then NO im guessing it doesnt detect it? if so am i screwed or what?
again thanks for the help!
I reflashed the phone and this is what came up:
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100187010 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
Elapsed:14 secs.
is that whats suppose to come up?! also on that tutorial you gave me i followed the steps other than this step….(After that klick “Add” and add MAIN and FS Flashfile according to your phone model and CID Version)
if i didnt follow this step would it not flash properly?
ok good only your EROM was gone if XS++ says only baseband and platform.
reapair EROM and flash the phone with SeTool 2 lite.
now reflash phone. using XS++ or SeTool 2 lite in 2+5 mode.
Hi Akshay, I need some help please.
My K800 was gone for nothing since last week. I just turned its alarm on when I was in a train, and suddenly, it turned off, and never come back… The only thing it reacts is red blinking.
I’ve tried this tutorial (provided a full battery and USB flash driver installed), but SeTool 2 lite didn’t recognise my phone. I also tried with KulanKendiClient but it didn’t work either.
What’s your suggestion that I could do now?
Many thanks,
and have a nice week-end.
Does XS++/SeTool2 recognize it with full battery? If not, (and drivers installed ok, and full battery) it is probably a hardware problem so better take it to a SE service center, I think.
Have you ever flashed it before? When it was working? If you haven’t then your drivers are likely not installed properly. Use a working phone to install them.
Hi Peti, thanks for your respond.
In fact, I used another working K800 to install the driver. And now, if I connect that phone (not mine) to the computer, it’s automatically recognised as if a normal USB. Does that mean that the driver was successfully installed?
And I think it’s quite strange to let it go like that, am I right? I didn’t drop it down or sth, why it stopped working in the first place? Or it’s just kind of normal thing with SE phone?
Thanks again,
PAUL.
Connect that WORKING k800 to XS++
Or Start SeTool 2 lite and Click Identify and connect working k800 holding C.
If XS++ or SeTool 2 lite Catch the phone then USB Flash drivers are installed.
If phone connects as Regular USB device then drivers are not installed properly.
Hi Akshay,
XS++ and SeTool 2 lite did recognise the working phone. But it’s still no hope with the dead one. What should I do now? And I don’t think the SE service center is a good idea because it’s too old for that 🙁
Thanks,
Does SeTool2 detect it with 2+5? And is the battery fully charged? If this doesn’t work then… maybe the fastport of the phone is damaged. Some hardware issue.
No, SeTool2 doesn’t detect even I press 2+5 for almost 6,7 minutes. (It thought that I should press long time because even with a working phone, it took 90sec to identify the phone while pressing C button). So you mean, there is nothing I can do now?
By the way, while searching with google, I come up with another site, where they told that for the last resort: open the phone, take out the internal battery, reinsert it. Then try again with SeTool, or Kulan client. I cannot open it for now because I don’t have a right tool to open it. But does it really work? Is there anyone who did try it once?
Many thanks,
Hey Akshay,
Im having the same problem as Alvin did before. I also have a w580i. But i dont get any flashing lights, the phone is just completely dead. I tried reflashing it with XS++ and SE but it gets stuck. It only goes up to like 100/460 blocks and then it either says error verifying blocks or just freezez. I reflashed the EROM but it still wouldn’t power on. PLEASE HELP!
@Paul: never heard of it, but it may be worth a try, what can you lose… 😉
@Sunny: it seems that some flash chips are damaged. If battery is ok and it ALWAYS stops at 100. Still, try JDFlasher.
Its not always 100. Sometimes it only goes up to like 50. Ill still try JDflasher. But what do i do if flash chips are damaged?
I tried with JDFlasher but it got stuck at 86/460. What should I do now?
If your battery is full and the cable connects perfectly (!!) then it must be a hardware problem, you can only take it to a service center.
Could it be just the battery that’s dead? I’ll try with a new battery. Thanks for ur help
Yeah, of course it could. And also try flashing with the new battery before giving up. 😉
Ill give that a shot. THANKS
Hi Askshay! I’ve read through all these and I am having the same problem accept I haven’t flashed my phone or anything… It was working one minute and I got on a plane (didn’t turn it off) and when I got off the plane I was getting the red blinking light and haven’t been able to turn it on since. I put my phone to charge a full 24 hours and nothing … Because I charged it, I tried to identify it with se2lite and although it read it for like a second it disconnected really quick. Is it possible that the battery is soooo low that the charging startup doesn’t have enough power to load?
got trouble…
can somebody help me..?!
my phone is k800i (its CID 52, RED)
i try to flash it to k810i with XS ++..it says ‘succesfull’
but when i turn it on……
my phone says ‘…plese wait…’
but at the same time, the LCD blinked white (continouslly).
after a few minutes (about 45 minutes),it look like working…but…the blingked light is not stoped…
what hapen?!
can u help me..
thanks..
regard..
an…
a’ve change the ‘main firmware’ an ‘file system custpack’ for k810i..
hhh….
please help me…
Veronica.
First point. How Did you Install USB Flash Drivers ?
If your phone is not working you need another working sony ericsson to install usb flash drivers.
Red Light blinks most of the times due to power supply fail. Try to use your phone with a new battery.
If Power Circuit and battery is alright then SeTool 2 lite Detects the phone easily.
You get a 2nd SE phone. Click Identify button in SeTool 2 lite and then Connect phone holding C. That will tell if your USB drivers are installed or not.
Then Recharge the dead phone’s battery and if necessary repair the phone with SeTool 2.
Last my name is not askshay, its AKshay. 🙂
Oon..!
Reflash back to k800 and start phone. Also is your EROM also dead ?
And one more thing.
Write back original GDFS .
I hope you have made a backup of your GDFS.
Don’t write some ones gdfs. only your k800 gdfs will work.
http://www.akshayy.com/sonyericsson/tutorials/restoring-a-gdfs/
Hi Akshay! Blame my fat fingers LOL! I did what you said and it identifies the working phone fine but when I try to repair the red blinking one (i’m calling it blinky now) it says something about the CS loader refusing to start and that this error is fatal.. I read on the thread and you told someone to reflash their phone if it is detected by XS++… I did connect using 2+5 but it says “did not receive 0x5a, Continuing…” and seems to hang up there… on the bottom it says port open ok though…
Any advice would be great.
Thanks in advance.
Thanks in advance
XS++ can’t fix this thing. Only SeTool2lt is useful now. I think you should keep trying it for a while. Now is your battery charged?
Yes the battery was charged in the working phone until it was full.
What should I be doing in SE tool2lt? Should I flash the phone? Which file do I flash it with?
When I try to Identify the phone it gives me the following just in case:
ChipID:9900, EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CIS:51 PAF:1 IMEI:01127100643595 CERT:RED
FLASH CID:52 COLOR:RED
MAPP CXC article:
MAPP CXC version:
Language Package:
CDA article:
CDA version:
Default article:
Default version:
Operator: 000-00
CORRECTION:
This is what I get when I try to identify Blinky
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100643595 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:106 secs.
ok. redlight also blinks and CS loaders also won’t start.
that’s a double problem.
first time we are seeing something like this.
which phone ??
i guess we can’t help you.
things will really get complicated now if you try to follow our instructions …
better visit a service center.
they will have service cable, which can catch dead phones easily and flash them.
at home you don’t have a service cable,, so repair also becomes tough and complicated and risky.
It’s a W580i. Wow leave it to my phone to be the dud! It’s so weird one minute it was working and the other not…. Do you think the SE Updater would work?
Hi I have the same Problem I was patching my phone and forgot to check the box that says bybas security… and It couldn’t start afterwards , the screen was flashing.. after that I tried to restore the GDFS and downlaoded one form topse.ru it was for my phone(w880) and now It doesn’t start, the red light is on just like here in this tutorial and I can’t do anything.. I have checked the battery is fine it’s almost full… I’ve tried your tutorial, am doing it now but when I click unlock /repair and connect the phone it doesn’t see my phone, does it have to see it or it flashes my EROm , I’m gonna leave this til morning but would like to know if I’m on the right track..
Hi, I’ve made the process that you describe, but I have this message:
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
loader prologue returns invalid status
phone pre-boot failed,possible RECOVERY needed.
Elapsed:8 secs.
Any suggestion?
Thanks in advance…
Great !! w580 !!
Did you know something ?
Most of the w580 first batch sold have defective EROM. Sony Ericsson has replaced many many w580 !! Its well known that the w580 has weak EROM.
you can try SE Updater.
Jekis. NO solution dude.
you wrote back alien gdfs. so your phone now can’t be repaired.
you should always write your own gdfs.
Rodrigo. your phone is not starting at all.
nothing can be done with free software.
you will need recovery tools.
my fones dead but the red light doesnt blink at all, the battery was 50% wen my phone suddenly switched off
mufaddal. so what’s the deal with the phone.
is it battery that failed your or the EROM.
Install USB drivers and try to flash erom. may be you are luck and its the EROM.
if its battery circuit we are sorry. its hardware fault. better take help of service people.
No red light. Reflashing all might help.
yea i went to the repair guy he told we will do one last try if it doesnt work, then the IC is dead may i know wats the ic
Try wikipedia first. 😀
http://en.wikipedia.org/wiki/Integrated_circuit
i read all threats but couldnt find the solution
hmmmmm ?? means ??
well..
it doesn’t help either..
i have write my gdfs, an restoring it using setool lite..
but it still white screen blinking…
writing gdfs, an reflashing is succesfull..
but didn’t work….
Which firmware did you flash on? K800 main?
Do you have memory stick IN the phone?
When did you make the gdfs backup?
i have a w850i i pluged it in the to my pc, i have 5 red lights flashin wen i turn it on, buh it doesnt show up on my pc, how do i fix this
hi akshay… mine’s a w580i. got the red blinking light…
thing is, i’m completely new to this whole thing. i’ve downloaded the usb flash drivers and setool lite… problem is, i’m the only one around here with an se phone. what do i do???
Hi just wanted to say thanks for the help about 4 weeks ago. Sent the Phone back to SE and they said something inside has blown they are waiting for a part and it will be returned to me free of charge. Thanks
I followed the above steps for my w580i Red Led Blinks but handset is getting flashing it showing fatal error
Stacey
its a well know fact that w580 has a low quality EROM, every now and then a w580 is damaged.
prahakran.
just try to fix it this way.. if it works then good. else get it replaced.
chris
your phone EROM is dead as said. you can’t connect the phone to PC wihtout USB flash drivers.
install USB Flash drivers using your friends phone and then connect phone holding 2+5 and repair the EROM.
schyzco
yes yes we have many w580 with dead EROM..
i have said it many times…
w580 has a weak and low quality EROM chip… that’s why
Sony Ericsson Replaces w580 for free…basically the entire main chip in the phone is replaced…
you try to repair .. of course you need some other sony ericsson phone to install usb drivers..
if repair does not work.. send it to sony ericsson service center.
they will replace for free.
how do i install those drivers from the phone ?
could u post a video, screenshot
A tutorial, search for “USB flash drivers”.
yeah there is video tutorial for that.
link to usb flash driver install tutorial is given in this page itself.
im pressing c and nothing happening
hey i got a new battery for my phone but it still never worked. then i took it in to a repair shop and they said the phone is dead and can’t be fixed. Im now following one of ur posts on how to restore a GDFS. Ive done everything as far as writing script and saving the file. Now I need a working GDS for 580i. Can someone plz tell me where I can get that from or would be so kind to share one with me.
chris.. did you re insert battery…..??
god know what’s wrong.. this is the 1st step besides.
sunny..
what happened to your w580i ?
if you have warranty then get it replaced from sony ericsson.
they will replace it for sure.
and how is the phone dead byw ?? how exactly did it ide ?
red light blinking by any chance ?
THANK YOU VERY VERY VERY MUCH!!!my phones finally working after like 2 weaks!!! I tried about a hundred things and even took it to a repair center. I had the phone on charging then I took it off and immediately connected to setool and i was able to flash the main and fs. So I guess the problem was just the battery but I did try another battery and it never worked. Im just happy that it worked now. Thanks for all your and Peti’s help earlier though.
hm.. tried.. doesnt work.. when i try to charge the battery i get the same red blinking light like when i try to turn it on.. btw.. model is k610i..
so… repair/unlock:
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 0 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
FLID unknown:897E
phone pre-boot failed,possible RECOVERY needed.
Elapsed:20 secs.
Recovery doesnt work… waited 20 mins and it didint do nothing… + identify doesnt work too..
btw… what happened… phone turned of itself… then i turned it on.. and it did work.. that happened one time more… like 3 hours after that… and then.. i didnt start again.. btw.. battery was charged… probably like 70-80% left…
so Akshay… any solutions?
i turned my phone off, and wen i attempt to turn it on 5 red flashes show up on “c”. i re instered the battery and nothings happening. i dont have warrenty, i use rogers.
Loaded 0 flash descriptors
hm.. thats probably why recovery doesnt work.. so.. anyone have any to share… or some firmware?
R1GB001 CID52 S_E_EUROPE? anyone?:)
Buddy I hav SE w550i 2day I was tranferring files vthin some other folder n I interrupted it in between by cancelling the process ma fone suddenly turned off n just white glow is in the disply I took off the batt it turns off as soon as I connect the Batt. the same white light is in the display plz buddy help me out vth ma prob…
one thing that you should know too… if i hold C and connect phone… nothing happens… it only works with 2+5…
chris..
if red light is blinking.. let me remind you, your phone is dead. it can’t be connected holding C.
You need a working sony ericsson phone to install USB Flash drivers into your computer.
then you can repair the dead phone using setool 2 after connecting it in 2+5.
when you hold 2+5 and connect the USB cable powers up the phone.. Usually power comes from Battery.. but not when 2+5 connection.
ROMC.
your EROM is fine.
some other component in the phone is damaged.
if only EROM was damaged then it can powered up by usb cable and reflashed…
try a last attempt to update phone with SEUS.
or ask a sony service center to reflash phone with service cable.
reflash… hah … im gonna try that seus or just try to flash it to w660:)
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100030623 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:14 secs.
20:27:42| XS++ v3.1 (Darwin) Ready !
20:27:42| Executed on Microsoft Windows XP
20:27:48|
20:27:48| Attempting to open the interface…
20:27:48|
20:27:48| TURN OFF PHONE!
20:27:48| Hold ‘C’ button on phone and connect phone NOW.
20:27:48| You have 30 seconds…
20:27:48|
20:27:56| Did not receive 0x5a. Continuing
20:28:01| Disconnected… Unplug the phone
20:28:02|
20:28:02| Attempting to open the interface…
20:28:02|
20:28:02| TURN OFF PHONE!
20:28:02| Hold ‘C’ button on phone and connect phone NOW.
20:28:02| You have 30 seconds…
20:28:02|
20:28:06| Did not receive 0x5a. Continuing
Hey chris don’t promote the full version it’s here all free
Chris is not promoting any thing.. lol..
that’s the setool 2 log and its that way only.
full version can do a lot more though.
man chris i don’t really know.. how to fix your phone at home.
you need a service center help with professional software and service cable…
nothing seems to work for you….
this Red light blinks in many cases even when EROM connection of phone fails due to hardware damages.
is there any way else i can fix dis
you saved me thx!! Your the man!!!
Only SE service center.
well..
i’ve give up..
i’ve brougt it to SE service..
and now it work again..
but..
its change from CID 52 to CID 53….
wew…
well thanks…
anyway peti, yes its k800 main, an yes my m2 was inserted….
Hi Akshay,
My phone w580i is not showing anything on screen. Initially it was vibrating whenever I try to powerup. I tried to follow your tutorial. I installed USB drivers. Now when I used setoollite F(with SIM and 512 M2 card still in) it changed to red light blinking status. I am doing following sequence.
1. Start setool application on computer.
2. click unlock/repair button.
3. while pressing “c” button of w580i I connect phone cable to USB port as shown in setool application.
4. Then when setool is done repair. I press key 2 and key 5 with cable still connected to computer.
Nothing happens, please see following log of my latest attempt.
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35928501974625 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed:29 secs.
Please let me know where I am not following steps.
Thanks,
Hey MAN! — you saved me a long time … the procedure was quick and fine … thx a lot … just post here SeTool 2 Lite link fot the others! … or I will 🙂
Here’s SeTools 2 Lite link (version 1.11):
http://seflashing.extra.hu/?mode=dlSoft&name=SeTool2v111.rar
@mg: first try reflashing main and fs.
@Lupyno: this message of yours won’t be seen for long, as many comments arrive at this post.
Hi i have k610i and he cant turn on red light blink every time i try it turn on or charge battery i tried over xs++ ,setool2,davinci,wotanclient. when i press c it nothing happen but when i press 2+5 every program find it and load somthing but after two,three secund says faild plizz help … Thnx.
Maybe your battery is low and the EROM is gone. Try to ask for a working battery from a friend.
Also it is possible that the cable or the connector on the phone is damaged, did it happen before that you couldn’t connect for long?
thank you so so so muchhhhhhh …
this tutorial is very helpful …
my problem just got solved ^^
Hi..
Uhh.. I have never done something like this before and I was wondering if someone could help me??
So this is what I tried doing:
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:53
skipping empty loader…
Can’t load ID loader !
Elapsed:6 secs.
Elapsed:6 secs.
ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:53
skipping empty loader…
phone pre-boot failed,possible RECOVERY needed.
Elapsed:0 secs.
Is anything wrong?? My phone still doesn’t work :[
your phone is CID53 and is not supported.
sorry.
get it fiexed from Sony Ericsson Service Center.
And one more phone saved… Thanks a lot!!
i also have cid53 and am waiting for a tool since i dont really think there is a nearby service center in the united states
For CID 53 the tool is JDFlasher, but it can’t fix dead eroms and so.
my phone started blinking 5 times and it doesnt turn on now, ung using k800 cid53 can setool lite repair this? and it is possible to charge my phone if its low battery?coz i think before it happens i thinks it was below 10%thanks
The red light sometimes means low battery, try charging.
SeTool 2 Lite won’t fix a CID 53 phone. So if it is EROM prob, you must take it to a service center…
i have a w580i and its dead its blinking like 6x a think can you tell me how to fix my phone co’z its dead and a can’t use it anymore.. pls… help me…
Isn’t this tutorial for you? :O
Hello Akshay
thnx for al the help
but when i do this it doesnt work
i have tried multiple times and still same result
i have tried charging and nothing is working
can u plz help me
ty
Isn’t your CID 53?:O
hey akshay,i have a w880i ,yesterday it turned off while charging,(after i took out the battery when it hung up).when i tried 2 switch it on,red light blinked inside the ‘c’ button….
i tried se tool lite1.1,it didnt even detect the phone,itried kulankendi client it too was a failure….
now i took it to the service cente ,he told me the data was corrupt and he needs 2 buy something 4rom SE ,and demanded Rs.850…..
do u think it is ok??
please reply(if possible on my mail too)
thanx..
If SeTool2 Lite can’t detect it after reinserting battery and while holding 2 and 5, it’s not really possible for you to fix it at home. But you can try other fixers for lower prices.
Akshay, I have a W810i, yesterday I changed my SIM for a contact no and again inserted my own SIM. After that I am unable to start my phone, its red light is blinking around 12 times and then goes off, if I press the power button again the blinking repeats again. Blinking rate is little high thats why Im not sure about blinking number, its around 12 times. Pls suggest what to do.
If you also reply via email it will be easier to access for me. thanks
Red light is also a sign of low battery, first try to charge it. If it won’t fix it, you try this tutorial, it will fix EROM problems. If still not working, reflash main and fs.
(sent in mail)
Hey, soz about where this comment is but my school blocked the flashing tutorial for the s500 to w580. can any one give me a vid tutorial cos i did it exactly as it was set out and all that happened was i got the walkman 2 and step counter that is useless any way
PLEASE help!
What else do you want? 😮 W580 has those, that means the crossflashing WAS successful.
i’ve fullt charged my battery, but still nothing happens. do you thinkg the hardware’s already dead? what happen to my k610i was, it fell on the ground hard. then hang, i reinsert the battery then now i can’t turn it on. when i press the power button it will only blink the red light, when i press it again it will blink i think 5 times.
Hey I have 2 k790a phones. One works perfectly, meaning I always have a charged battery… the other one though I’m having problems with. First of all it doesn’t turn on at all, doesn’t vibrate, doesn’t blink red. It cannot connect using “C” in setool2lite or xs++ (both programs show as if I didn’t even attempt to plug a phone it) But using the “2+5” method, setool gives the first few messages and then says “BOOTROM MODE DETECTED” and then does nothing else… it doesn’t bring up any of the phones information.. no imei, no info on whether or not its RED; Brown etc… no firmware info, nothing nadda ziltch. Trying to do anything (flashing, identifying, reading gdfs) results in the same fashion. So is there ANYTHING that can be done to bring this phoen back from the dead?
p.s. I love the site… its been a great help for my other k790a which I unlocked and debranded successfully.
@Carlo: yes, that can only mean that. Some circuit insite broke. You mean you have installed USB flash drivers with a working phone and can’t connect like this, right?
@Arto: it seems you can’t fix it at home. Maybe a service center can do it, with pro tools.
Is there anyway to repair a dead EROM on a CID 53 phone?
No, not yet. Only professional (BOX) tools can do it. Red light blinking, huh? 🙁
Yeah… red blinking light. How sad.
Try inserting a fully charged battery first. If still not ok, take it to a service center.
my phone turned off and refuses to turn back on. I took it to the att store but the guy didn’t know what was wrong. When I attempt to turn it on it blinks red on the side. CAN ANYBODY TELL ME WHATS WRONG WITH IT??!!???!?!??!?!?
Don’t you try this tutorial then?
Thank you very much! I had a dead K610i which came back to life thanks to this tutorial. I am in debt to you!
hi i think i had an erom prob. cuz my phone was dead with the red light blinking an it was fixed using setool2 lite 1.11. bu now the phone wont charge when i plug it in it says charging non standard battery its a k790a what do i do someone please help me my batt is dyin
Is the phone working? Can you start it and make calls? If so, probably damaged battery. I heard a story that a guy had his phone on the charger and the battery just blew up. Anyway, first try reflashing main and fs. If the battery still isn’t ok, buy a new one.
the batt is ok i charge it in my friends phone an it works fine after it is charged. its not the batt or the charger they both work. do u no anything about a batt calibration? i read on a forum they had the same prob but i have no clue what to do or where to find 1
i flashed it over already using xs++ an it works fine just wont charge only comes up with that stupid message charging non standard battery
No clue, if the battery is fine, then maybe some prob in the GDFS, not fixable.
I mean not at home. Service center should help.
so why can’t i fix it. what does GDFS stand for
does any one know what a battery calibration isan where to get 1
I don’t know if that even exists.
Hey now that i finished my S500 project i tried to revive my dead K800 with selite but it wont connect, battery is 100% charged cos used friends K800 and held 2+5 while connecting but still didnt work.
Any Ideas?
Hi, my w880i has just stopped turning on. i try to charge it and a funny buzz noise keeps repeating out of the speaker every second. ive left it for half hour and its still doing it with no charge in the phone whatsoever. someone please help.
Ryan: Connected and then what?
@Joel: Install USB flash drivers and SeTool 2 Lite. Try to connect with C button. If you can, reflash main and fs. If can’t, connect with 2+5. Then Unlock/Repair — fix erom. If you can’t… 😕
what woul the service center do with my phone that i can’t do my self?
i live in Trinidad an that would cost a lot to carry it to fix
i didnt connect, held 2and5 for 5min and still ddnt connect
@richard: You have free tools and they have pro tools ($5 000).
@ryan: You have flash drivers on? And is the fast port ok? (I use WD-40 to clean it.)
flash drivers r installed and hav no idea what a fast port is
Where you plug the cable on the phone.
ill try that. also with selite2 there were drivers called 4in1. do i have to install them cos it said it is for 95, 98 and 2000
i just tried doing it with my w580i but it says
ChipID:9900,EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100613749 CERT:RED
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:28 secs.
please help? this is my new replacement because of the cracked keys thing….
can’t build loaders chain ;(
wats a “WD-40”. Can u use alcohol swabs
hmmmm what ????
i don’t know.
josh..
forget it. its dead. no way to fix for free with free software.
you should try service center.
w580 out of production for good. lame unstable erom inside the phone.
Hey Akshay
I have a K800 and it has the red light
it has full battery cos friend has same phone.
i have the flash drivers for XS and selite but i tried holding “c” and 2+5 and still didnt work.
I also got 4in1 drivers which came with selite but didnt install them. How can i fix it
PS where can u get a vista QVGA pack with menus for S500/w580
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
Z610i
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35783001346253 CERT:N/A
FLASH CID:52 COLOR:RED
Abort all operations.
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:90 secs.
Will backup GDFS now.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35783001346253 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:21 secs.
please help..
when i connect using phone xs msg shown
if i press connect and i press c button.. nothing happend.. below i connect and press 2+5 button
16:58:07| XS++ v3.0 beta (Sinyar) Ready !
16:58:07| Executed on Microsoft Windows XP
16:58:11|
16:58:11| Attempting to open the interface…
16:58:11|
16:58:11| TURN OFF PHONE!
16:58:11| Hold ‘C’ button on phone and connect phone NOW.
16:58:11| You have 30 seconds…
16:58:11|
16:58:19| Baseband ID: 9900
16:58:19| DB2020
16:58:19| Protocol Version: 3.1 <——-show only this!!!
please help
Hi,
I seem to have the red blinking light issue as well. When i use SEtools to repair the EROM, i get the Restoration File Not present Error. Somebody else had posted the same issue above but i didn’t quite understand your reply. I tried running the exe in the make_rest folder but that seems to do nothing.
hi Akshay i have a k550 it has problem.when i connect the phone to setool lite 1.11 it give me error like..
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
err: 32 (30)
loader header not accepted
Can’t load ID loader !
Elapsed:6 secs.
please tell what shuold be do..
Oh GOD !! This Red Light which is sign if serious issues is a tough one to fix !!
I only this way to fix it. Other methods need SeTool 2 full which is paid software.
and no need for those 4in1 drivers for our use.
You can get those themes in topse.ru and other forums like se-nse.
……………..
brocas, what’s the problem ?? your EROM Is gone again… setool 2 lite can’t fix it ?? if phone has warranty then get it repaired from SE.
……….
Rohit !!! you should create restore file using your main and fs firmwares with help of make_rest.exe
………….
Adil !!
did you install usb flash drivers ????
But i dont understand topse since its in another language
yeah.. !!! try seusers.com
also our download page it has a few links
ok i had the same problem as tim. i followed the guide and my comp crashes. lol. power went out. then i left the phone charge for a day n it started workin.
i have k790i. by mistake i flash my friends k790i’s gdfs file system on my phone. now the phone is not working any more. i tried fx++ ans setools lite, but they also not detect my phone.
plz help me!!!!!!!!!!!!!!!!!!
I have k790i. by mistake i flash my friends k790i’s gdfs file system on my phone. now the phone is not working any more. i tried fx++ ans setools lite, but they also not detect my phone.
i have backup of my gdfs file system
plz help me!!!!!!!!!!!!!!!!!!
Hi people,
The problem I have with my Se K850i is that the red light underneath power button stays on continuously when the battery is charged….any ideas?
good. it was bad battery then.
Pardeep i don’t know how to fix your phone. Try this tutorial ! Sorry.
try to write back your gdfs.. no other idea that i have.
naf !!
hmmm i don’t know, that’s a new phone and we are still not into hacking it. but we will soon get there.
Hey Akshay, the RED LED of my v630i just blinks after I flashed it with the wrong GDFS, It gets detected with SETool2 1.1, and I’ve tried reflashing it to v630i FW/Main, and Tried using the k610i GDFS from http://www.techgsmnet.com/unlock-mobile/setool-support-center/5775-hello-guyz-pls-share-good-gdfs-se-fones-here.html , but the problem still persists, and I only get upto
15:46:43| XS++ v3.1 (Darwin) Ready !
15:46:43| Executed on Microsoft Windows XP
15:46:47|
15:46:47| Attempting to open the interface…
15:46:47|
15:46:47| TURN OFF PHONE!
15:46:47| Hold ‘C’ button on phone and connect phone NOW.
15:46:47| You have 30 seconds…
15:46:47|
15:46:53| Baseband ID: 9900
15:46:53| Protocol Version: 3.1
in XS++., Anything else I can do ? Or is it just dead ??
It blinks 6 times when I try to power it on.
Here is what SE tools does, when I try Unlock/Repair
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35194101868040 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:51 secs.
This is with Recovery,
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35194101868040 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:51 secs.
RECOVERY MODE STARTED
BOOTROM MODE DETECTED
skipping empty loader…
All possible recovery loaders fail. That phone not supported
Elapsed:27 secs.
Please Help Me!!
hmmmmmmm sorry, i don’t understand. its perhaps hardware defect in the battery circuit , check out.
hey i have been trying to connect sony ericsson w580i to a microcontroller.. i checked the voltages level at the transmitter n receiver pin through a CRO. the bit pattern is fine. yet its not communicating.. i feel maybe there is some prob with the baud rate or the bit pattern.. so someone please help..
What do u mean by that ?
I’ve tried with 3 diff batteries including the original one….
@rutvij: And?
@Samith: HW defect is not fixable at home.
@rutvij: can’t use DCU-60?
So, if I take it 2 a place where they fix cell phones, I could get it repaired ?
hi! i’m a new user of sonyericsson s500i i had same problem with phone is dead and red light is blinking when i press the power botton but this time it blinks 6 times… like i said i’m just a new user, so i dont have any idea how to fix it… i hope u can help me… where can i get the xs++ and setool 2 lite? is there any wesite that i download it? please help me…
Hey aksh
Hey guys, I hope someone can help me with this. My w580i that isn’t even a month old had been working perfectly after flashing, changing main, fs unlocking, and adding flash themes. More than a week has passed since I last flashed it. Last night, I left it connected to the charger, and this morning when I was going to use it, it was off. I tried turning it on and no luck. I tried taking out the battery and reinserting, and turning it on, it vibrated while I had the power button pressed. I tried this more times and the same thing happened. I tried removing the SIM and reinserting, pressed the power button, and it vibrated until I removed the battery. Now it doesn’t do anything. I tried connecting to SE Tool Lite with 2 and 5 pressed, but no luck. What should I do?
Thanks in advance.
Hey akshayy i was patching my fone usin SEtool lite and i was able to do quick asing access patch usin ur tut and then after applying the patch there at the bottom of the setoolite came a message if not connected in 15 secs disccont the fone i did it and frm then my fones DEAD !! no Red light flashing too i tried ur above tut tooo and SEtool lite said these
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35220601803199 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs.
plz help me Its my sis fone she’ll return tommo n8 plz help me 🙁
sorry guys for all late replies
have been busy with life !!
Ariel ! Service Center is your best bet.
Its well known that w580i has a defective EROM. SE has stopped w580 production.
sorry for you. get it replaced from SE.
Azeem. sorry. can you try to reflash main and fs and cda using XS++ 3.1
check out here.
http://www.akshayy.com/sonyericsson/tutorials/flash-firmwaredebrand-with-xs/
Hey Akshay,
I just read everyones posts and did what you’ve been advising since the blinking red light seems to be a common problem. The thing is that when i flashed my phone to repair it after following the instructions, i got this report
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35373602078350 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:7 secs.
I really have no idea what this means. It seems that something is terribly wrong am guess.
Thanks in advance.
Noel
First flash your phone with XS++ or with SETool 2 lite.
To flash the main just add the main firmware mbn in the big box and click flash, in setool 2 lite. same way flash FS and then attempt to recover.
CSloader refused to start GDFS services,error is:29
That means your FS needs flashing. So flash main and fs too via 2+5 ! SeTool 2 lite.
Hi Akshay, thanks for the help. But i am having trouble finding the right link to download the correct mbn file for my phone. I have W580i and haven’t been able to find an appropriate link. If you have a link or something it would be great. I don’t want to install the wrong firm ware by mistake. 🙁
hey akshay,
I have a w580i with this blinking red light problem.
I understand all your instructions but I’m worried that sony will detect that I modified my phone.
I already reported my phone and they are sending me a new one. However I am trying to get some pictures off the phone before I return it. So will repairing the EROM via SeTool2 lite cause any problems with warranty? Will they say that I modified my phone and charge me?
Btw – I have never flashed / debranded my phone so I’m just wondering if this will cause any problems?
Thanks – appreciate it
Hi Akshay,
I flashed my phone with SETOOL and installed the new firm ware and FS.
When you said recover, do you mean i click the recovery button or do i click the Repair button. Because when i attempted to repair my phone i got the same error 29.
So am a lil confused right now as to what am supposed to do.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35373602078350 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:6 secs.
Thanks
my w580 is not getting on,it has been dead for 2 days……when i tried to flash with the main file it says “verify block error”…first a red light was blinking at the side which is not blinking now..i also tried the EEPROM with the “unlock repair option”…help me out na
hey man i tried dis but stil ma fone aint workin…plz man help me out…i dunno wats wrong…its gone dead n does not switch on….i hav a w580i…it went dead wen i was flashing it wid few themes….now d onl thin i get is a red light wen eva i charge it…..help me man…thanks in advance….
the fone gets detected by xs++…bt it doesn switch on…help me man…is it somethin major???i tried d GDFS backup nal…but no good….
Hey Akshay,
i have a k800i and i followed each direction carefully on getting the phone recognized by usb, which it was but im having problems on setool lite, the option to unlock and repair the phone is shaded grey. i read practically every post, (i know i have some serious time on my hands lol) one person had the same situation, but mine appears to not even react to the phone at all…any help? your response would greatly be appreciated! thanks!
Vanee, this is really complicated. how did you install flash drivers when your phone is dead ? do you have other SE phones ?
install and try and repair
this is not guaranteed fix. but works many times.
Fazil.. go for full reflash of phone then, main, fs and cda.
Noel go for a full reflash again ! with XS++ or SeTool 2 lite !
w580 are really defective, they should be take off the market immediately
hi. i got 2 dead k800i phones here. i resolved the first phone by updating its firmware from sonyericsson website. now, the second phone cant be updated since it says “phone firmware is up-to-date”. my question is: is there any way to reload the latest version? just to fix the white screen fault on my phone. please help…
Greetings to all,
I got this (I’ve k550im turned into w610 with your tutorial. Dead after a while)
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35491101007050 CERT:N/A
FLASH CID:52 COLOR:RED
set_gdfs_props failed, exiting
Elapsed:18 secs.
Elapsed:18 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35491101007050 CERT:N/A
FLASH CID:52 COLOR:RED
set_gdfs_props failed, exiting
Elapsed:12 secs.
Elapsed:13 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35491101007050 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
wrong response, break.
failed, that is fatal
Elapsed:197 secs.
Aks,
I tried to unlock Se k750i (cid49, r1ca021)
with a correct vkp file (setool lite 1.11) but in vain!
ive got a w880i and when i turn it on the “c” button flashes 5/6 times.setool xs++,wotan cant regonise it.im stuck ireally need help.
hey, the problem with my phone- W810i is that when i start is it just red light dot thing ok, i know that you have Low batteries then, but when I try to load the battery it’s just that white light blinking and nothing happens! Is my phone broke? I used it 10 mins ago and it was fine, but then the batteries died and that white lightening started to blink, i dont know what to do :(. Please help
I got an s500i that froze while I connected the USB cable to it. Now it’s got the red light. I need a little help resetting it though. The instructions aren’t that clear (to me at least). I opened the program, plugged in my USB cord to the comp, clicked unlock/repair, then plugged my phone into the cord while holding 2 + 5. I sat there for 20 minutes while nothing happened …
I have a problem with my w580i. It was working perfectly and then all of sudeen it started to turn off by itself. Now it doesn’t turn on and the dreaded red light is blinking on the side. Please help me fix this problem i don’t wanna go buy another 1 because i don’t have warranty.
And i know that it wasn’t the battery i tried it in another w580 it worked perfectly. i charged my phone for the whole day and it still won’t light up. it would vibrate then nothing would happen. After a few vibrations the red light of death would start blinking.
i tried doing this part and it doesnt work…whenever i take out the battery and put the battery back in and click 2 and 5 , and click unlock/repair… it says it’s ready and it’s done but nothing happens i cant turn on my phone
@junior
your erom is dead!
read the tutorial mentioned above you will be able to get it done!
@mike
still red light blinks?
if not then reflash your phone!
Hi peti,
u helped me once… to flash my k550.. it was a success story..thanks.
now i am back with a v630.
Current Phone status:
————————-
1) Phone is just dead.
2) Tried to repair with SEtools- it says:
BOOTROM MODE DETECTED
FLASH CID:52 COLOR:RED
loader startup: executed
CSloader refused to start GDFS services, error is:29
ailed, that is fatal.
Please help me….
What is next?
@kochumvk
akshay is off for few days!
peti is not here now!
and i really dont know anything exact!
so better jump into here
http://www.se-lifestyle.com!
here you will get peti too!
thanks bhuvan.
hi can i use any other sony ericsson phone to install usb flash
@eduru
not getting u exactly…u mean…u wanna install flash drivers??
my dead phone is k608i but i k800 to install the flash but setool is not detecting my k608i
@eduru
so u mean..u wanna just install drivers for ur k608i and to do so..u r using k800…
well…i would suggest u to use gordons gate drivers!
it will detect every flash
u can get it in file base
i did evrything that is on the tutorial and my phone still won’t start up.
This is all i get evrytime i try flashing it. After that nothing happens:
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100254467 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed:15 secs.
By the way my phone’s light blinks 9 times and not 5. Could it be possible i have another problem?
hi can u help me,after i try make quick access patch my phone cannot switch on. can u please help me.below is the attachment from setool..please…
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:359445101745667 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS service,error is:29 failed, that is fatal
Elapsed:14 secs.
@Junior
then for a healty discussion and a righ solution come here
http://www.se-lifestyle.com
i’ve bought se k850i on 22 sept, but unluckly my phone having problem with same symptoms… red light flasing on start button and my pcsuite also don’t detect my phone. when i’m leaving that phone attach to my laptop it sometimes installing new haedware found and its all about firmware… any suggestion how to fix my se k850i?
@charles
follow the steps given above
your erom is dead!
Hi, i have a K800i,red light blinking.Tried to repair erom using setool,not being recognised holding “c” button,only when you hold 2 & 5,but this is all i get.
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35908801532916 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:15 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35908801532916 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:14 secs.
If i am not getting the correct firmware,how can i reflash my handset.Any suggestions will be greatly appreciated
Hey, I’ve got a 580i that was working fine until it spontaneously died yesterday and I’m getting the blinking red light.
I installed the flash drivers without any problem (recognized holding down ‘C’) and installed SE Tool2 1.11. I connected to SE Tool2 with both ‘2+5’ and ‘C’ – in each case the phone was detected. However, I’m getting no change in the state of my phone (still blinking red).
Any suggestions?
Cheers for the guide!
greetings of the , plz help me…i hi i am from netherland antilles, i had modded the se m600i , then accidently i had press master reset button, no after i restarted the se m thee is only a black screen of death (only bak screen) and i cannot see anything,, if used xs++ it detects it but does repair , far manger does no detect it , setool lite does detect it,
plz tell me how to bring my se m600i back to life plzz
you have to repair the phone by test points …i mean you’ll now have to go to a service personel.i did get the same case and did so.
PLEASE HELP.
my fone fell down the toilet about 5 months ago, and since then it hasnt been able to turn on
i had it working in like october then it just turned off but some of the buttons didnt work.
anway – everyyime i stick the charger in the fone, the red light down the side turns on, and its not the battery light.
its a sony ericson black thin one its new i had it in march this year & it was my best friend so please help me try and fix it x
I have w800i cid 36 brown .i read some tut that u can change it to red with the far manager i did all the steps and it said flash succssfuly i think it was erom flash.i unplug the the phone and it dead .there is no any sign of life no blinking no white screen just dead. seus cant recognise the phone same as setool and xs++ in normal mode and 2+5 mode . please help me>>>>>>>>
sorry, i don’t know about that.. from red to brown.
i just did this and now when i plug my phone into the charger…the Sony Ericsson splash screen stays on..is this normal?
hey man, where can i get a working copy of the setool lite v2?? the ones on the internet isnt working 🙁 thankzz
from se-lifestyle.com
isnt there any hope to fix my dead phone
This is my Email in case someone want to help me [email protected]
hi, i updated my EROM on my w800i with FAR now its dead, cant start cant charge cant connect to the computer, i just want to be able to connect it to the computer ive tried everything but no succes
same here brother inthink there is no hope
🙁
did you try to repair ?????????????
try to flash via 2+5
you join us at our forum, there queries are answered by many
Ive tried everything!
should i try to connect it with my friends computer? will that work?
when i press2+5 there is nothing shown i can connect is with any programme .
and Christian i hope you find a soulotion for you problem and when you do it please Email [email protected] me coz i have the same problem
hmm. have you installed usb flash drivers correctly ?
Its your battery charged well to 100% ??
Isn’t your phone being detected ?
You should press a button like Identify and then connect phone holding 2+5 ! in SeTool 2 lite.
If this does not detect the phone, check your computer and cable. All fails means hardware fail. I hope you find out some solution. 🙂
i downloaded it and it worked once…. by the time i went back to use the program it wasnt there!! help me akshayy!!! i used the seus to get the drivers. is there any special way to get it to work?
i not even seeing the icon it had on the program link…. when i click on it, it says i may not have the permission to use it 🙁
can u email me a working copy? i downloaded it 3 times from selifestyle 🙁
[email protected]
thankyou in advance!!!
i did not understand you !! you want to run setool 2 lite ?? run as Admin in vista. what’s the problem ??
if its setool 2 lite 1.11 you can get it from 4shared.com
go to 4shared and search in that site using the search function there.
else google search, you will get. its 20 MB to email. sorry.
my phone k530i wont turn on, however it doesnt blink red 5 times either, it wouldnt turn on after i tried to reverse an unlock patch, i have no idea what to do can someone help me?
im using windows xp black….. all that i download contains a virus 🙁 and i am the admin. do u think its the black xp?
hey man, i tried it on windowx xp… i go through but now i getting the error no ack during gdfs_readvar! cant read SCRC unit… when i try to flash the phone!!! wow this is stress…. lol
what do u recommend?
CSloader refused to start GDFS services,error is:29
failed, that is fatal
i choosed the s500 handet… an this is the error i get now 🙁
uhm i have a ericson z310a its doing the same thing that light is flashin and i dunno what to do i dont think this phone has a usb cord to be honest it never even came wid one :S
if u can help msg me at [email protected]
thanks
hello, i have an s500 and the red light blinks about 5 times. i read this entire thread and i got all the required software etc. when i do the step – unlock/repair to repair the erom, i get the error msg “CSloader refused to start GDFS services,error is:29
failed, that is fatal” as well. Please help me, v.
REPAIR UR EROM!
ITS STRANGE!!!MAY BE…BECAUSE UR PC IS EARLIER INFECTED!
FROM WHERE DID U DOWNLOADED?
WHAT ARE U DOING ACTUALLY??
BAKING UP UR GDFS???
@SHESH
1….THIS SHOULD NOT HAPPEN.!!!THERE IS NO BUG IN FLASHING STUFF!
2….AND WHAT ARE U DOING EXACTLY???
THE RED LIGHT IS BLINKING???
JUST RECHARGE UR FON…IF DOESNT WRKS…DEN REPAIR THE EROM!
hey…i flash my erom color brown to red…i use far manager….after i flash…my phone cannot start…canoot conect to pc…conot charge….what i will to do to back to normal…plese help me…sorry bad english….
use ur erom colour as orginal one…dun change it acc to u…as its orginal security settings for ur fone!
re flash it…
i am repairing the erom, i tried another working battery but its the same problem. now im getting the same error tht dhal is geting when i try to repiar the erom…. “CSloader refused to start GDFS services,error is:29
failed, that is fatal” what do i try now? i followed all the steps accurately…
this is the exact error im getting
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35908501531160 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:88 secs.
Elapsed:88 secs.
this is the error when i select s500 on the screen b4 i press the unlock repair button…
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35908501531160 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:10 secs.
does ur fone gets connected prssing the ‘c’ key procedure??
then restore back ur fone gdfs!cuz its damaged
how to reflash it.. using setool 2 lite…and hold2+5…?
my phone w800i cid 39….after flash erom color the phone dead..can’t start,,can’t charge…can’t open the phone plse help me….
what about my phone how can i fix it i know its just EROM error but i cant connect the phone to fix it
@bhuvan, i connect my phone using the 2+5 since it doesnt turn on. how do i restore the gdfs?
and i dont have a back up!!! but i can get my cousins phone? mmhmm ?
my phone isnt starting but isnt blinking red, and it definately isnt the battery, every time i try to repair it, it says something about failed, that is fatal,
please help
@hairi
get it done using the 2+5 thing with se tool!
connect it using 2+5!
still dont gets connected…den better go for service center!
firstly…ur phones gdfs is unique!
dont evn think of restoriing and other gdfs!
ull fone will gt bricked!
and thru 2+5 thing…repair the erom!
then is should start back!
cuz if the red ligh is blinking then erom is dead n dis is the only way out!
i get this error when i try to repair the erom, CSloader refused to start GDFS services,error is:29
failed, that is fatal
so what do i do now?
i have gdfs backup and all i did is flsh new erom with farmanager may be its for k750
gdfs is corrupt!
ur fone is not connecting thru “c” key procedure too??
if ya…then sorry bt no way out…better get it to service center!
@ahmed
i am not getting u!
new erom???why??
@henry
then no way out!
aint ur fone gtting connected thru pressing c key procedure?
what can i try guys? plz help me 🙁
i get this error when i try to read gdfs and also when u try the unlock/repair
“CSloader refused to start GDFS services,error is:29
failed, that is fatal”
there must be a way, plz help!!
thankz 🙁
@shesh…
id askd akshay…wait for his rply
akshayy, what shud i do?
@shesh
akshay said dis
using SeTool 2 lite, Add the main and fs in the big box.
Then click flash.
And connect phone holding 2+5
Then after flash, dis connect and then repair it. Then flash CDA and start phoen.
thanks man, but what is the main, fs and how to flash CDA?
i dont see anything written about CDA on the program.
please give me some details, im new to this. I like it though!!! 🙂
@shesh
main…the main part of firmware….u cant access it…only need to flash it!
fs[file system]…where u will be replacing files like…strtup screen…drivers….which support the fone to run!
cda[cust pack]files which contains…few tweaks for ur network settings!
if u dont upload cda files…ul get an error as:configuration error!
select each part for ur region
thanks man, so where do i get the fs and cda files?
thanks alot…. im already feeling like its been fixed!!
I’ve found a way to fix k810i phone when it won’t turn on or have white screen of death.
I just reflash the phone with main and fs also custom pack using XS++.
Then use SEtool1.11 to reset the erom to 0000.
After that is done, you take out the battery. Leave out the battery for about 30 minutes to an hour.
Then insert the battery, plug in the charger. The phone should start charging. Let it charge fully.
After fully charged, unplug charger, remove battery. Insert battery and turn on phone.
Pls note: If your phone halts while recharging then reset erom again. Remove battery and leave it for longer period of time.
I have no idea why this works for me. It just works. Just wanted to share my experience. Peace.
@shesh
search on google…or go to our support forum and request there
@hmk4life_99
nice!
Hi, i have SE K610i, blinking red for 5 times and it is not on. Hope i can get some good advise here..
I had try to use the SETool2 (lite edition) v1.11 (the USB flash drivers were built in) so when i installed SEtool2 lite, i automatically had this usb flash drivers
I connect my phone via the USB cable i got from SE when i bought this phone…
I pressed 2+5 button on my mobile phone
Not sure if the computer read the USB connection or not, as i cant see any difference…
Now, i had follow the instruction above, but i have been waiting for abour 201 secs.. nothing shown up in my screen. So i click STOP button, and it stated :
Abort all operations
Can’t load ID loader!
Elapsed: 201 secs
PS: battery is NOT empty, and I removed all SIM cards+memory cards+ battery (except i insert the battery when i pressed 2+5 as shown on the instruction above this page)
Can someone please be so kind to help?
Merry Xmas and Happy New Year =)
@bhuvan i flshed new erom to change mine from brown to red
hey i have a w800i..cid39 calor erom brown….after i change the color erom brown to red my phone dead….can’t charge,cant’ conect to computer…and when i conect to setol lite I pressed 2+5 button on my mobile phone
Not sure if the computer read the USB connection or not, as i cant see any difference…
Now, i had follow the instruction above, but i have been waiting for abour 201 secs.. nothing shown up in my screen. So i click STOP button, and it stated :
Abort all operations
Can’t load ID loader!
Elapsed: 201 secs
plse help me….
sorry my phone cid 36
@ahmed
so now any query???
Help me please….
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35945101134677 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:98 secs.
Elapsed:98 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35945101134677 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
only FLASH operation supported in that mode
Elapsed:13 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35945101134677 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CID52 BYPASS PROCEDURE STARTED
Processing part1…
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2…
Processing part3….
BOOTROM MODE DETECTED
OTP LOCKED:1 CID:51 PAF:1 IMEI:35945101134677 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS “READY”
HOLD “C” BUTTON AND ATTACH PHONE
CID52 BYPASS PROCEDURE FINISHED
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader…
embedded flashloader not responds !
Elapsed:406 secs.
why????
@Mr.Aam
what i think is…u have nt attached ur fone back well…or the pc did nt detected it
tri it back again
‘i dont understand for what u meant… after bypass the DB2020 security, software tell me to take out cable from my phone, take out batery and reinsert back, after i do that, “THEN PRESS “READY”
HOLD “C” BUTTON AND ATTACH PHONE
CID52 BYPASS PROCEDURE FINISHED
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader…
embedded flashloader not responds !
Elapsed:406 secs.”
i do many time,but still same.. please Help me…
sory for my bad english. im form malaysia…
i heard somthin about a added driver to pick up any red light phones that are undetected by any program, some1 said its was the gordon gate driver, were can i get if it excists
i have w660i phones.the problem is my phone is now dead and cant be turn on.i try the SETOOL 2 LITE VER.1.08 but it say:
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35958401156997 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs.
HELP ME PLS…
hello….
nobody cant help me??? please….akshay…bhuvan… (-_-)
@akim84
if u gt da backup of ur fone…then restore it
it is damaged!
@Mr.Aam
wait…let me get this query to akshay!
will rply widin a day!
@ryan
gordon gate driver aint got any link with red light!
Hi,
i need help. i have a w850i.
initially, the phone was damaged by the front face being disconnetected to the back parrt. i took it to get repaired and then the repair man showed me that there was a red light flashing in the infrared bit.
i’m tryin to foolow your tutorial but my phone doesnt seem to connct to the computer. what do i do
i don have the backup files..what should i do now? did the phone is really dead and cant be use anymore?
Okey Bhuvan… I wait you help… also akshay…
hi akshayy, i m messaging you after a long time, i haven’t mess with my phone ( k790i )since long, it was working perfectly, except that the joystick had stop working, today i tried to clean, i had done this before, but today suddenly it went blank, with re light blinking, i tried this method with setool lite, while pressing 2+5, but still phone doesn’t start, following are symptoms:
1: still red light blinking,
:2: phone gets started if connected to adapter, but if removed and than restart, than again red light blinking,
:3: flash of camera goes on anytime,
:4: keys 2,3,7,8 have stop working ….
what should i do ??
following is the log of setool lite:
Chip:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed 921600
OTP LOCKED:1 CID:51 PAF:1 IMEL:35220701263115 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314HANCXC1329139_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CDloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed: 32 secs.
@akim84
aint gt gdfs backup???
and if red light is blinking then go for 2+5 procedure!
@Mr.Aam
sorry for so late reply actually akshay is busy in fixing a lot of things!
well…y dont u go for jdflasher???
look in patching through jdflasher guide here!
@rushabhits the hardware fault
so go fr service centre now!
@ shayis
ur fone getting detected by ur pc?
bhuvan bhai, just have a look at this page :
http://www.topsony.com/forum/showthread.php?t=6462
my phone got back to normal (with damged joystick too, its normal guys), in just less than 1 minute…
@akshayy and @peti, please make note of this page , its useful and like icing on cake !!!
sorry i forgot to mention it was XS++ method which solved the problem and not se tool lite method
hello ashkayy/bhuvan
Im trying to revive a red blinking s800i that wont turn on. I tried both XS++ and SEToolsLite2 with no avail.
I cannot make a gdfs backup, the option in XS++ appears in gray, this is what i get
14:19:52| XS++ v3.1 (Darwin) Ready !
14:19:52| Executed on Microsoft Windows XP
14:19:59|
14:19:59| Attempting to open the interface…
14:19:59|
14:19:59| TURN OFF PHONE!
14:19:59| Hold ‘C’ button on phone and connect phone NOW.
14:19:59| You have 30 seconds…
14:19:59|
14:20:04| Baseband ID: 9900
14:20:04| Protocol Version: 3.1
And then nothing, the disconnected phone sound is heard from my PC.
On SETOOLSLite2 i get the following:
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35683301781676 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:12 secs.
Will backup GDFS now.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35683301781676 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:11 secs.
After this it wont let me do anything. Please help me this is my sisters phone im trying to repair
You should flash the FS connecting the phone 2+5 mode, then try again.
Hi Ashkay,
i did what you told me, but XS++ responds the same:
22:15:41| XS++ v3.1 (Darwin) Ready !
22:15:41| Executed on Microsoft Windows XP
22:15:47|
22:15:47| Attempting to open the interface…
22:15:47|
22:15:47| TURN OFF PHONE!
22:15:47| Hold ‘C’ button on phone and connect phone NOW.
22:15:47| You have 30 seconds…
22:15:47|
22:15:55| Baseband ID: 9900
22:15:55| Protocol Version: 3.1
And then the phone disconected sound again from the PC
On SEToolsLite2 i get this after flashing my FS (Which was successful apparently):
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35683301781676 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:13 secs.
Please help me, im sorry to be such a hassle but its really important i get this fixed for my lil’ sister
ok, flash the phone with SeTool 2 lite. Flash the FS and Main.
download main+fs, extract them, in the big white box add the mbn and fbn file. click flash and connect phone holding 2+5.
@Mr.Aam
sorry for so late reply actually akshay is busy in fixing a lot of things!
well…y dont u go for jdflasher???
look in patching through jdflasher guide here!
______________________________________
hmm… i dont know how to use Jdflasher tool. can u tech me???
hi akshay..can a newbie with no experience in fixing software problem of SE phone can do it with just a simple tutorial??im trying to reprogram my SE k800i..where can i get the complete tutorial?the main problem now is i cant open the application and game folders..it says operation failed..then someone told me that it should be reprogramed..is that the real solution?tnx in advance..
hello ashkayy
Im trying to revive a red blinking k810i that wont turn on. I tried both XS++ , this is what i get
23:41:55| Attempting to open the interface…
23:41:55|
23:41:55| TURN OFF PHONE!
23:41:55| Hold ‘C’ button on phone and connect phone NOW.
23:41:55| You have 30 seconds…
23:41:55|
23:42:05| Baseband ID: 9900
23:42:05| Protocol Version: 3.1
after that nothing happens..What do i do?
Thanks Ashkay, i still have one problem. Apparently i need the S500_R6BC002_FS_GENERIC_RED52 or S500_R6BC002_FS_AMERICA_RED52 FS file, as im using the S500_R6BC002_FS_CENT_EUROPE_RED52 on an american phone and there is always an error during the FS flash.
Any idea where i can get the FS file? All the sources i try are down due to them being old and almost everyone else only carries the S500_R6BC002_FS_CENT_EUROPE_RED52 one.
we have jdflasher tutorial ready check out.
then its best you get it fixed from service center. it costs only 6$ or 250 Rs.
yes classic case, fix using setool 2 lite.
you can get them at esnips mirko750 folder.
just google search esnips mirko750
Fantastic – Thank You. Phone was switched off due to low battery and then wouldnt charge or switch on.Just the blinking LED!I hadnt got drivers installed but although I got errors on installation and it took over a dozen attempts to get the phone to hold its connection to the PC it finally worked!Phone was left on charge overnight and SIM replaced the following morning.All now working.Thanks Again.
here is the log file after following the tutorialFLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:34 secs.
the phone is still dead . pls reply me through e-mail on wat to do .
@Tanvir
its because your gdfs is corrupt!!!
if you got the backup then restore it
My Sony Ericsson W200 phone is effected with Trojan Horse Virus. I have tried to remove it by formatting the memory card and phone card. But as soon as I connect my mobile with PC it is showing that both memory card and phone card is effected with virus.
On the other hand my mobile’s memory card is not working properly as it has already been formatted.
Anirban. wrong question.
please don’t ask all that. here.
hey akshay bro i need some help with my old k608,when i try to start my phone it just shows a black screen and does not starts,the key pad lights flashes but the phone doesnt start,should flash the EROM in this case?????
@sadman
try reflashing…
hey, i downloaded setool 1.11 lite but i don’t know how to install it, can you show me how?
it doesn’t do anything when i hold 2+5 when i pressed unlock/repair.
@ Ranno
first you have to install usb flash drivers!
get one from our filebase[gordon gate’s flash driver]
then open se tool and click on unlock/repair
now connect your phone holding 2+5
cant reflash,xs++ cant detact the phone,and my dcu-11 is also not installing although i have cd…
@ sadman
installed usb flash drivers?
what problem are u facing??
if red light blinking then follow the tutorial
if u get the error 29 its due to flashing in a warm room. do it in an air conditioned room or place your phone in a cool place for a while before you flash it.
however i just stick my phone in a zip lock bag. put in freezer for 10 minutes. then use setool list 1.11 to flash main+fs using 2+5.
don’t do the freezer trick if the phone is precious to you. i only did it because i don’t have air conditioning room. hope it helps.
does it matter is its brown and not red?
because it reads but nothing it happening.
askhay i’m trying this procedure on a v630i model. how long must i wait on holding 2+5 while setool is doing its stuff by pressing the first button. i have been holding it for more than 3 minutes and nothing is being recognize
@hmk4life_99
lol….nice joke!!
fake
@ Ranno
no…it should be red only!
@ von
installed usb drivers??
it should recognize fast!!!
Red light blinks 6 times whn i press power button.. Nothing else happens… this is what i get wnh i repair with SEtool2lite….
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35489401205948 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:31 secs.
I’ve tried in many ways… it’s still not working….. what could be wrong with it… it happend after i restored gdfs file that i got for my w610 from
http://www.se-life.ru/index.php?name=FW&page=gdfs&folder=GDFS_in_BIN_Format/
What should i do now? PLz help me….. This all happened for my eagerness of modding from this forum….. I need ur help…. I cant buy another phone now……
When i try to rar the SeTool 2 lite files i keep getting a virus warnig.
I am having the red blinking problem on my w580i
I downloaded the flash drivers and the se tool.
I open the program ,select what phone I have ,hit the unlock repair button, hold c and hook usb cable.
How long does it take for the fix to take place. I think it isn’t doing anything at all. It still says press c and hook usb and the blue progress bar just keeps filling and repeating.
Any feedback will be greatly appreciated. Or maybe a walkthru. thx
I hooked up the phone pressing 2+5 and got this.
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35256002740946 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
after pressing c and hooking it up i got this—-
am I not waiting long enoug?
Elapsed:64 secs.
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:438 secs.
jerry, sorry, setool2 lite was not updated to support CID53 repair. you have no option but service center.
as told above, w580 has EROM issues.
Greetings! When I try to connect my cell, I select the appropriate device (a w610i) and check the box which says ”Bypass DB2020 Security”. When I click Unlock/Repair, the only thing shown is just the progress bar that just keeps going! No information is shown, what do I do?
An update on my situation, I just pressed the stop button, and the program said ”phone pre-boot fail, possible RECOVERY needed”. I tried that but also without result, and I see that even the red blinkink lights dont appear anymore, any idea about the problem?
ah , well i guess it’s time to get an exchange on the old tele. I gave it a try tho. thx AK
when try to switch on my k608 it shows a white screen then goes black,key pad lights are ok. I tried to connect it to my pc through dcu-11 but pc does not detect it. I even tried to connect it in xs++ but it does not detect it either. I got flash usb driver installed but the problem persist. Is it a hardware problem???
What should i do?
@ Metzas
if windows says that it is unrecognized object…then connect it again by twisting the cable…and clean tha jack…somtyms this happens because of dust between connectors!
now….install the usb drivers
@Metzas
if your phone was not connected then how can it get repaired???
no way!
n that log…it always sayz the same
nt a big deal
@ bhuvan
My phone was connected, prior to connecting I installed the appropriate drivers and Windows recognized my phone as a flash device when I connected it pushing the 2+5 buttons. The problem persists thoughtm cant think of any solution 🙁
@Metzas
if ur pc connected it the way u r saying
then its all fine
try ref;lashing main and fs both now
Hey, i got a k770. i was shutting down the phone to charge, but when i plug it to the power outlet. the red light blinks and won’t charge. So i tried to turn it on, but same thing happened( red light blinks). i download usb driver, setool but when i press 2+5 nth happened…
what should i do? is there a sony ericsson service center in canada?
I have w610i CID53 .
Can I repair red light with far manger ? couse this is the only program witch can detect cid53 . I still have my phone warranty but I think they won’t repair it because I have instaled europe firmware instead of baltic .
Is there any way to repair CID53 ????????
@debbie
dont know about canada as we are from india
for service centre look at sony ericsson site
well…first install usb drivers too!
get gordons gate drivers from out filebase
isntall
open se tool
now press unlock/repair button
now connect yor fone to pc..pressing 2+5
@Gytixas
cid:53 cant be repaired in case of dead erom
but service centre guyz will repair it…because…they cannot start the phone either
they will get u a new motherboard
bhuvan, it still doesn’t work tieh gordon gate driver…. still doesn’t do anything when i press 2+5… i called SE service center yesterday and they refuse to fix my phone because they said my model is not yet released in canada… yet i thought SE is international?
dear ashkayy, i have tried everything i found on the net to revive my dead K800i but nothing seems to work..it still flashes those red diode when i plug in the charger or plug in the usb cable…need help…pleaseeeee
@debbie
yea…this condition is there here in india too!
well….this is the only way left out now
in this works!!!!
i mean…u r d first with whom this aint working
@jimzt402
whats exactly happening?
yea… i took the phone to two phone repair shops and they said they don’t know what’s wrong with it…. so i’m shipping my phone back to hong kong… i hope they found out what’s wrong…
Hey Guys
I am a new techbee so ignore my details. Here is a puzzle. I read for 3 days continuosly before i flashed this w850i. I had the same bloody white screen and those red lights blinking up.
After going through hundreds of threads, I realised noone is sure where the problem is. Half believes that this could be Hardware trouble, but I already brought it back from the repair man who checked it properly and tried the new pcb board and lcd screen but in vain. So I BELIEVED THE OTHER HALVES (SOFTWARE TROUBLE). Decided to give it a full go.
Before going any further, let me say this.
1. XS++ (any version) didnt work for me.
Baseband ID: 9900
Protocol Version: 3.1……….. That is all what it could tell me.
2. SEUS couldnt recognise the phone.. “””IDENTIFICATION FAILED……”””””
3. I am in Australia and use this phone here but it was actually bought in India. Why I said that is because most of the users wont be happy to see the Custom pack, FS and MAIN I used. I tried to be reasonable but couldnt get more than two or three files of each for this model.
MAIN—————–W850_R1KG001_MAIN_GENERIC_CY_RED52.mbn
FS——————-W850_R1KG001_FS_C_ASIA_RED52.fbn
CUSTOM PACK——–W850_CDA102568_7_R5A_GENERIC_C_ASIA.zip
4. I think there was a trouble writing Custom pack. I will highlight that part.
5. Yes, GDFS is secure with me. But I didnt get any option to save the original MAIN or FS or Custom pack.
Well I am done… here is the log..
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35240101207673 CERT:N/A
FLASH CID:52 COLOR:RED
Model:W850i
Brand:Sony Ericsson
MAPP CXC article: R1KG001 prgCXC1250204_CHINA_CY
MAPP CXC version: R1KG001
Language Package:APAC
CDA article: CDA102568/101
CDA version: R5A
Default article: cxc1250489
Default version: R1KG001
Operator: 000-00
Elapsed:6 secs.
Will backup GDFS now.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35240101207673 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
stated number of vars:1831
Found:533 variables
Found:749 variables
Found:485 variables
Found:64 variables
GDFS read all done, GDFS_35240101207673.BIN written
Phone detached
Elapsed:32 secs.
FILE RECOGNIZED AS CUSTOMIZATION PACKAGE.
CDA:CDA102568/7
MODEL:W850i
VARIANT:C_ASIA
LANGUAGE: EN
LANGUAGE: AR
LANGUAGE: RU
LANGUAGE: TR
LANGUAGE: UK
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35240101207673 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
writing \\Hers\e\Desktop (This is Active Desktop folder)\Sony Ericsson\W850i flash files\W850_R1KG001_MAIN_GENERIC_CY_RED52\W850_R1KG 001_MAIN_GENERIC_CY_RED52.mbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:9200
Will flash 460 blocks…
SSW loading returns:0
writing \\Hers\e\Desktop (This is Active Desktop folder)\Sony Ericsson\W850i flash files\W850_R1KG001_FS_C_ASIA_RED52\W850_R1KG001_FS _C_ASIA_RED52.fbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:4740
Will flash 237 blocks…
SSW loading returns:0
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader filesystem startup: executed
loader GDFS startup: executed
Writing package…
chdir: 2
Directory not found, attempt to create(THIS IS WHERE I SAY COULD BE SOME TROUBLE WRITING CUSTOM PACK)
chdir: 2
chdir: 2
chdir: 2
Directory: W850_CDA102568_7_R5A_GENERIC_C_ASIA/tpa/preset/custom/
CONTENT_DOWNLOAD_HOOK.itm (10240)
Customize.xml (1082)
FM_PICTURES_HOOK_3.itm (10240)
FM_SOUNDS_HOOK_3.itm (10240)
FM_THEMES_HOOK_3.itm (10240)
FM_VIDEOS_HOOK_3.itm (10240)
GAMES_HOOK_3.itm (10240)
MEDIA_PLAYER_HOOK_3.itm (10240)
ORG_APPLICATIONS_HOOK_3.itm (10240)
preloaded_config.xml (99012)
SETT_RINGTONE_HOOK_1.itm (10240)
SETT_SCREENSAVER_HOOK_1.itm (10240)
SETT_STARTSHOW_HOOK_1.itm (10240)
SETT_WALLPAPER_HOOK_1.itm (10240)
VIDEO_PLAYER_HOOK_1.itm (10240)
Phone detached
Elapsed:407 secs.
If you think I have done something wrong, plz advice me how to correct it (if possible in detail)…..
Thanks
Just adding to the last comment…. As suggested by AKSHAYY and the other guys, I tried to repair EROM with the Unlock/Repair tool of SETOOL but unfortunately nothing happens… here is the log
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35240101207673 CERT:N/A
FLASH CID:52 COLOR:RED
Model:K700
MAPP CXC article: R1KG001 prgCXC1250200_GENERIC_CY
MAPP CXC version: R1KG001
Language Package:APAC
CDA article: CDA102568/101
CDA version: R5A
Default article: cxc1250489
Default version: R1KG001
Operator: 000-00
Elapsed:6 secs.
Elapsed:6 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35240101207673 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed:28 secs.
Thanks for every help…
I just realised from the log that setool is finding my phone model different now.. My flash files must be wrong.. Can you guys gime the right ones…
Thanks
@debbie
they just wanna leav your phone like that
it is known worldwide that service centere service is really bad!!!
same here in india…but here…i had same problem..but they got new motherboard
well…wish u luck!
@Amar
phewww!!!lol
well…whats the exact problem???
red light blinking???
if yes then….the se tool way is final and last one
2+5 thing is the only way out!
when u connect your phone to pc holding ‘c’ key what happens?
does pc says semc flash device?
Hello Bhuvan
Yes the red light is blinking if I try to switch it on while charging.. I didnt count how many blinks.. Advice me if it means something..
If I try to switch on without charging… then it vibrates once, flashes white screen and then nothing…
SEUS says……
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35240101207673 CERT:N/A
FLASH CID:52 COLOR:RED
Model:K700
MAPP CXC article: R1KG001 prgCXC1250200_GENERIC_CY
MAPP CXC version: R1KG001
Language Package:APAC
CDA article: CDA102568/101
CDA version: R5A
Default article: cxc1250489
Default version: R1KG001
Operator: 000-00
Elapsed:7 secs.
Ofcourse the above symbolises that I have USB flash drivers.
Thanks again
@Amar
dude
if white screen is cmoing up…then surely its erom aint dead!
try other battery!
and then re flash your phone!
Plz suggest me the appropriate MAIN, FS and Custom pack… what about the error while flashing the first time (plz see the first log I posted). I want to make sure I flash them with the right files.
Thanks folks
@Amar
go to topse
go in firmwares section and now get the latest one cid:52 one
@bhuvan
i dont know what happened, i mean the phone simply gone dead..does not turns on..only those red diode blinking when i put on the charger or the usb cable…tried connecting it with wotan, kulankendi, XS++ and setool2lite but nothing seems to be recognizing my phone.. nothing happen when i connect the phone.. i recharged the batt overnight..tried to connect again in the morning but nothing…i installed usbflash drive…but its not appearing on my pc… i tried connecting my P1i..the cable is fine..even all the software above is fine..is this mean that my K800i is officially dead…please advise..tq in advance
@jimzt402
so.,…when u put it on charging does red light blinks???
and at any single moment…whatever u do…does screen goes on???like white screen???
if not then erom has gone dead
u need to do mentiond 2+5 method to get rid of it
whats your erom vesrion??
cid:52 or cid:53???
if less than cid:53 then u can repair it through setool lite cuz yet se tool do not support cid:53
@buvan
tq for the reply, .. yes when i put the charger on it does blink..i did 2+5 method but any of those software mentioned above do not recognised my phone.. XS++ says
16:34:19| Error: Cannot open phone communication port
16:34:21| Disconnected… Unplug the phone
what seems to be the problem…
i dont know my erom version coz i cannot get it connected to any of those software above.. all i want to do is to get my phone connected and i can do the flashing if it is an erom issue…please help
@bhuvan
and..the phone is not turning on at all…no white screen..nothing… i suppose the phone is dead forever….sigh…
Hi Jim, though I have got the trouble but i believe I can help you someway.. I just realised that when I was in your condition, I left my battery charging for couple of hrs. Luckily I checked the battery status in the other SE and this is what I get…
The battery was still in the last stages with almost no charging..
Charge battery in the other phone… It will possible help..
Amar
BHUVAN thanks for the post
Bhuvan and others, I reflashed it with full battery this time but no success.
As per you said, the red blinking lights are gone. I tried Repair/Unlock of SETOOL button but no success.
Thanks
Amar, its better then to get it fixed from Service Center. When hardware is in the problem, then software fixes rarely work.
@amar
Tq for sharing..i will try that tommorow…i keep u guys posted…terima kasih (malaysia)
@amar
u knw what…i tried to turn on the fone using my fren batt..but it wont…meaning it is not the batt..any idea?
@ Amar
ya
amar when nothing is working then go for service centre nw
@jimzt402
you have to use setool for that
not xs++
just check through setool
if still doesnt works den service centre
@bhuvan
setool does not read my phone…
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:103 secs.
it means service center…rite?…tq u all guys…
Well Bhuvan and Akshay, thanks… I will take it to repair center soon but I have a small fact which amuses me.
Till now I have flashed it 3 times but the
1. CDA is totally unchanged…(It had CDA102568/101 but I flashed successfully with CDA102568/2 then /7 and some other but even now CDA is same).
2. Phone name changed after first flashing… then is not coming back by any other flashing.. I will restore GDFS and then flash with different files than I used the first time.
Guys, thanks for the high spirits, but just like you guys I dont want to give up. I still believe somewhere from the searches that this can be a software trouble (though my mind doesnt say that any more)…LOL
I couldnt find anywhere the exact files on GOOGLE for the
w850 R1KG001 FS APAC CID52 for MBN
and the same for Custom pack..
Help guys
@jimzt402
ya
cuz i think its cid:53
@Amar
for firmwares go for topse
use this id
vishnuhost
danger
for cda….se nse…or google search…or search at 4shared
did u restored gdfs????
phone name changed from what to what????
and i am still not able to understand your first point
Hello Bhuvan,
I havednt restored GDFS yet. But now I am thinking why I Didnt. My whole attention was to get the correct files but maybe the first time flash files were corrupted.
Thanks Bhuvan for continuous replies.. Will be back soon…
@Amar
sure
unable to run setool as it comes up with warning from my AV and also when AV disable still get no access?
@sinbrad
thats solved at forum
add program to trusted list
it aint virus
dats for sure
akshay just want o ask something,,,i have an w580i phone,,but then i cannot turn my bluetooth on,,plus the camera of my phone wasnt working properly,,some one told me i have to reprogram it,,,could you help me,,,how to reprogram my phone??tnx..
@arlyn
re flash it
dont do it with seus
use flashin method
with xs++ or jd flasher
Platform: DB2020
23:45:40| OTP CID: 51
23:45:40| EROM CID: 53
23:45:40| EROM Color: Red
23:45:40| IMEI: 35471601xxxxxx
23:45:40| Phone ID: K800
23:45:40| Region: MEDITERR
23:45:40| CDA: CDA102568/4 R5A
23:45:40| Firmware Version: R8BF003
23:45:40| EROM: R3A016
23:45:40| Ready for operation!
23:45:48| Sorry, your phone is NOT SUPPORTED
23:45:48| Error: Failed to send CSLoader!
23:45:48| FSX Shutdown!
23:45:50| Disconnected… Unplug the phone
23:45:59| Shutting down…
Does this mean that my cid53 db2020 phone,is not supported to make a GDFS back up,from XS++?
If not,then plz how can i make a back up (just in case…)?
@john
no way of taking backup in cid:53 phones yet!
oh 🙁 ,ok.
In what exactly case could gdfs be damaged ?
Cause i was about flashing and patcing :p , until i read about GDFS and got horrified…lol,seriously
@john
not any particular case!
what problem u are facing exactly?
@bhuvan
I don’t have any problem :)!
yet :p ,i was just saying that i am afraid to go on,with patching cause if somethings goes wrong i won’t have my gdfs back up :O and i want it soo much(patch)
😉
by reading u r tutorials i revived my k800i..thanks a lot akshayy for posting those………
@john
a lot many cases!
better follow the way it is given
nothing will go wrong
@john
patches are removable!
and most cases reflashing solves it!
do the way it is given and no problem will be faced!
@jose
nice
Hi,
As everyone in this forum, I have the same problem with red light blink on my dead SE. I’ve managed to install drivers on to the mobile and connect it to the SEtool2lt, which shown report:
Chid id:9900, EMP protocol:0301
Bootrom mode detected
Speed 921600
Try to launch embedded bootloader…..
Embedded flashloader not responds
Can any one help me out, plz?
@Halfnelson
phone aint getting connected!
try twisting the cable…
Hello Akshay…
Ive read through the comments and just wanna get this straight for the last time…
I think I fried my EROM and I don’t think that I have the USB flash drivers. I say this because Ive tried using SEtools and XS++ and the KKclient, but none of the programs is detecting my phone in the 2+5 mode.
Tell me if theres any other way I can reactivate my phone and please doon’t hesitate from going into detail since Im a newbie with this..My phone is a w580i. none of my friends has this phone so according to what ive read, its gonna be a problem installing the drivers. please suggest a work around.
Thanx a lot and lemme tell you that uve done a great job of helping a lot of people here… I hope i’ll be able to say the same about my case.
@Sami
install gordons gate drivers from our filebase
install it
now try
if your phone is cid:53 then no way of fixing it..else it will get fixed
ok i need help my dad has a sony ericsson S700 and i changed the housing case or the shell watever its called and i tried to start the phone but there is a red light that blinks steadily i think it means that it is charging but wen i try to turn the phone on while the charger is still plugged in the phone still doesnt turn on and i dont no wat to do can u help me please
@Maaz
erom has gone dead!
follow the red light one tutorial
Hello Akshay.
I have a problem with my S500i phone, it happened when I was trying to unlock my s500i. The thing is that now my phone is dead, I can’t turn it on, charge it, etc. Unfortunately, i didn’t back up the GDFS. A Red light at the infrared port blinks when I try to start my phone. I tried the tutorial mentioned above but nothing happened. The setool recognized the phone when holding 2+5 but it didn’t repair it, and gave me the following error ” CSloader refused to start GDFS services, error is:29″
please let me know if there is a way to fix my phone. Thanks
@HFTB
now try reflashing
hey My Sony w580i doesnt start up when i press the power button it flashes red light on on side any idea how to repair it cause this cell was working just fine untill i took it outta my pocket and saw it dead i really love my cell and please reply soon or i’ll be screwed and tell me how to repair step by step pls
@lol
we all love our cell…
first try recharging it….
if nothing happens then follow the red light one guide
and get gordons gate drivers from our filebase and install them….then do all stuff in se tool
@bhuvan
Thank you.
Can you give me any tips for reflashing. Beside, neither setool nor XS++ recognized the phone when holding ‘C’ button.
@HFTB
See if JDFlasher recognizes the phone. If it does not, and you have no GDFS backup, I say take it to a service center.
@ HFTB
must be cid:53
use jdflasher
get the latest one from our filebase
@ HFTB
and yea..
if red light is blinking…and phone is cid:53
then no way out!
go for service center
@
the phone is cid:52
should I reflash it with cid:53 firmware or cid:52
hi again
In case JDflasher doesn’t recognize the phone when holding ‘c’ will holding ‘2+5’ work for flashing.
HFTB
phone is cid:53
and red light blinking is the rpoblem then go for setool…
that will help u!
try connecting again n again
I dnt know :'( but my ph is dead I want it working again 🙁 wat to do I just cant understand awl dis
i have the same red LED blinking problem with my w880. its dead.
though i managed to connect it by pressing 2+* keys (its not detected by 2+5)
but when i try to unlock/repair it with setool it gives the following error.
n its the battery problem.battery is abt 75% full
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35777401227431 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:52 secs.
so can u help me with this…
thanks
Hi I’m a newbie. I recently wanted to unlock my phone and tried using the tutorial on the website. I backed up my GDFS. Then followed the instructions given. When i finished my phone wouldnt even turn on. It didnt flash red at all. It just wont turn on at all. I tried to check if it was the EROM and it gave me the following msg.
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35256002451316 CERT:N/A
FLASH CID:52 COLOR:RED
set_gdfs_props failed, exiting
Elapsed:7 secs.
Elapsed:7 secs.
I tried to flash using XS++, but it wont recognize my phone. Now both programs aren’t recognizing. it. I have no idea what I should do. Please help. Thanks
Forgot to mention its a 580i
@Roupa
well whats exactly happening??
@ali
strange!
well try again…connecting for few more times
else jump to our forum cuz i am really not getting!
thats impossble!
u must have commited mistake somewhere!
when u connect your phone holding ‘c’ key what happens?
i mean…what does ur pc displays?
Hey guys,
I figured out the problem. The pc wasnt recognizing the phone, so whenever I reconnected it to the PC i had to remove the battery and then reinsert it. After that i just reflashed the MAIN. My phone is all good.
THANKS
says nothing it never connects using “c”.
can u likn the forum u talking abt
@ali
http://www.se-lifestyle.com
mine is cid53 erom is dead how can i flash it
can anyone help me plz
@anand
no way…
rush to service center
Good evening!
First of all Ive got w910 phone.
I want to know how to patch my phone with the sliding sounds.
Do I have to run the jar applications when I turn it off then on?
pls reply as soon as possible.
More power to all of you who helps us noobs.
senjeru
in a2 phones its runtime patching
once u swith off ur cell all the patches will be removed!
then ull have to again run jjpather to execute them…
for patches…jump to our forum
This is my problem…. help me plzzzzzzz.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35457901447176 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:32 secs.
morjako
what u wanna do?
Hey, my Sony Ericsson W580i froze a few days ago as I pressed the walkman button. I closed it and all of a sudden it switched off. When I tried to switch it back on, a red light started flashing on the right side but nothing else would happen. The battery was full, however i tried charging it anyway, when I switched on the charger, the same thing happened, I wouldn’t even charge up, It just flashed for 5 seconds and then nothing.
So after that I tried connecting my phone to the computer, but it just did the same thing, the computer couldn’t find my phone.
Why has this happened and how can I fix it? Any help would be greatly appreciated.
Thanks!
Jamie
follow this tutorial…red light blonking one..
that will solve it
i have a problem with my w880i. for a long period my phone was broked (about 2 weeks after i upgraded it, it switched off and wouldnt turn on). so i went back to using my nokia 8800, that broke and i took it to pieces and replaced loads of parts. then i dropped it in a drink and it stopped workin as expected. so went back to the sew880. i took it to a phone shop today and he told me some bullshit about replacing the screen (blatent lie cause when i got it back it hadnt been opened up and you can tell because of the walkmen sticker at the bottom). anyway he got it working regardless but it keeps freezing up. it turns on and works for 2 minutes and then freezes. so i take the battery out put it back in and it works for 2 more minutes. sometime the screen just goes black but the led backlight stays on and it needs the battery taking out. if i go into messages it crashes. if i make 2 phone calls consecutively it crashes. i’ve flashed the software using the se website but this has not solved the issue. occasionaly i get a breif red light flash from under the keypay but if i take out the battery and reinsert it the phone turns on for another 2 minutes. will using this erom repair technique fix my issues? thank you to anyone for your time. DrewBloke
hey i have sony s500i
i got the GDFS back up of it.
i want it to be w580. so i flashed it.
in the end it was done also.but the icons appear as large. so i write another GDFS of s500
by that the phone dead.
then i rewrited the original back up of my s500i.
then i use the setool2lt to repair mine.
it told like this in the end.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35344702627421 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed:47 sec
but my phone is not turning on.
what can i do????
please help me as soon as possible.
thank you
sorry that message was shown when i restored GDFS.
this is the message shown when i clicked the repair button.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35344702627421 CERT:N/A
FLASH CID:52 COLOR:RED
Model:S500i
Brand:CTI Movil
MAPP CXC article: R6BC002 prgCXC1123326_GENERIC_LY
MAPP CXC version: R6BC002
Language Package:ORANGE_GEN
CDA article: CDA102568/1
CDA version: R8A
Default article: cxc1123364
Default version: R6BC002
Operator: 505-02
and still my phone is not starting.
what can i do?
please help me.
hey i solved the problem
but now the screen is coming by half up and half down.
what can do?
———————
‘ ‘ ‘ ‘
‘ ———–/ ‘
‘ ‘
‘ ‘
‘ sony ericsson ‘ ‘
‘ ‘
‘ ‘
‘ ‘
‘———————‘ ‘
sorry about the drawing
that first half circle was sony ericsson simbols half circle and the rest come in the last line
what can i do?
drewbloke
u just blowed up ur phone like hell!
dont know if it will solve it…but yea…give a try
do i have to write w580 GDFS in it?
alvin abinayan
first try repair
hi bhuvan.
i also tried it.
please watch this video. this contains the problem in my phone.
http://www.youtube.com/watch?v=GnsofUMOoNA
please help me to solve it.
alvin abinayan
tell me the problem verbally
when i first flash this problem occord.
the facilities of w580 is working but the icons size are large.by that the normal half screen is displaying as the full screen.and the rest half are displaying above to the screen.by that can’t handle the phone normally.
alvin abinayan
lol
i guess u have uploaded icons which do not match ur phone
download which matches urs
is that all?
and where can i please give me the link.
is that include in the custom pack?
hi, I have a 580i, installed drivers and setools2lite 1.11. followed tutorial. this is the result. any suggestions or help would be appreciated. thanks! -daniel
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100116107 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:35 secs.
Alright, Do it again. But this time
Flash the File System of the phone. Download a w580i FS and unzip or unrar it and add it the big box in setool2 lite, clikck flash.
Connect the phone Holding 2+5,
hello akshay, thank you for your quick response. I did as you requested and ran into a similar (same) error below:
(flash step)
Elapsed:12 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100116107 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
writing C:\Documents and Settings\dh185016\My Documents\Downloads\W580_R8BE001_MAIN_GenericFS_America2Y_CDA_LARED52__Quick_access\W580_R8BE001_FS_AMERICA_2_RED52.fbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:4180
Will flash 209 blocks…
SSW loading returns:0
Elapsed:128 secs.
(unlock repair)
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100116107 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs.
I next attempted to flash MAIN then unlock repair and flash MAIN+FS then unlock repair without success.
Any further suggestions would be appreciated.
Regards,
-daniel
Daniel, Then only one thing left to try, recharge battery or try some other battery.
As i have already told w580 EROM suffers manufacturing defects.
pls help me with my k800i… last night i tried to restore my gdfs file using Xs++, i accidentally restore a wrong gdfs back up. instead of mine its the other phone. when i restarted. it won’t start i saw flashing infrared 7 times…. plss help… i dont want to lose a phone again.
here is the log file i backup using Xs++
23:53:25| XS++ v3.1 (Darwin) Ready !
23:53:25| Executed on Microsoft Windows Vista
23:53:25| XS++ v3.1 (Darwin) Ready !
23:53:25| Executed on Microsoft Windows Vista
23:55:26| Shutting down…
23:55:28| Shutting down…
00:33:07| XS++ v3.1 (Darwin) Ready !
00:33:07| Executed on Microsoft Windows Vista
00:33:18|
00:33:18| Attempting to open the interface…
00:33:18|
00:33:18| TURN OFF PHONE!
00:33:18| Hold ‘C’ button on phone and connect phone NOW.
00:33:18| You have 30 seconds…
00:33:18|
00:33:18| Baseband ID: 9900
00:33:18| Protocol Version: 3.1
00:33:18| Phone name detected!
00:33:18|
00:33:18| Profiling SEMC phone…
00:33:18| Platform: DB2020
00:33:18| OTP CID: 51
00:33:18| EROM CID: 52
00:33:18| EROM Color: Red
00:33:18| IMEI: 35570401xxxxxx
00:33:18| Phone ID: K800
00:33:18| Region: APAC
00:33:18| CDA: CDA102568/101 R5A
00:33:18| Firmware Version: R1JG001
00:33:18| EROM: R3A022
00:33:18| Ready for operation!
00:33:35|
00:33:35| Sending db2020_cid01_prodid_p3j.bin…
00:33:35| Applet ID: 070129 0950 NGUCXC1250330_DB2020_PRODUCTIONIDLOADER_P3J
00:33:35| This is a PRODUCTION_ID loader
00:33:35|
00:33:35| Sending db2020_mem_patcher_cid52_r2a006.bin…
00:33:36| Applet ID: 061205 1523 HANCXC9876543210_DB2020_MEM_PATCHER_R2A006 0
00:33:36| This is a MEM_PATCHER loader
00:33:36|
00:33:36| Sending db2020_red52_cs_r3a009.bin…
00:33:37| Applet ID: 070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
00:33:37| This is a CHIPSELECT loader
00:33:37| Activating loader…
00:33:37| Activating GDFS…
00:33:54| This loader is UNLOCKED
00:33:54| Backing up the GDFS…
00:33:56| Stated variables: 1725
00:33:58| Variables found: 460
00:34:01| Variables found: 791
00:34:02| Variables found: 218
00:34:04| Variables found: 256
00:34:04| Wrote backup to .\Backup\K800_35570401xxxxxx_GDFS_BACKUP.bin
00:34:04| GDFS was backed up successfully!
00:34:04| GDFS operation was successful
00:34:06| Disconnected… Unplug the phone
00:35:10|
00:35:10| Attempting to open the interface…
00:35:10|
00:35:10| TURN OFF PHONE!
00:35:10| Hold ‘C’ button on phone and connect phone NOW.
00:35:10| You have 30 seconds…
00:35:10|
00:35:20| Baseband ID: 9900
00:35:20| Protocol Version: 3.1
00:35:21| Phone name detected!
00:35:21|
00:35:21| Profiling SEMC phone…
00:35:21| Platform: DB2020
00:35:21| OTP CID: 51
00:35:21| EROM CID: 52
00:35:21| EROM Color: Red
00:35:21| IMEI: 35471601xxxxxx
00:35:21| Phone ID: K800
00:35:21| Region: APAC
00:35:21| CDA: CDA102511/2 R2A
00:35:21| Firmware Version: R1GB001
00:35:21| EROM: R3A016
00:35:21| Ready for operation!
00:37:58|
00:37:58| Sending db2020_cid01_prodid_p3j.bin…
00:37:58| Applet ID: 070129 0950 NGUCXC1250330_DB2020_PRODUCTIONIDLOADER_P3J
00:37:58| This is a PRODUCTION_ID loader
00:37:58|
00:37:58| Sending db2020_mem_patcher_cid52_r2a006.bin…
00:37:59| Applet ID: 061205 1523 HANCXC9876543210_DB2020_MEM_PATCHER_R2A006 0
00:37:59| This is a MEM_PATCHER loader
00:37:59|
00:37:59| Sending db2020_red52_cs_r3a009.bin…
00:38:00| Applet ID: 070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
00:38:00| This is a CHIPSELECT loader
00:38:00| Activating loader…
00:38:00| Activating GDFS…
00:38:22| This loader is UNLOCKED
00:38:22| Restoring the GDFS…
00:38:22| Attempting to write 1725 variables…
00:38:49| Wrote 1725 variables!
00:38:49| GDFS was restored successfully!
00:38:49| GDFS operation was successful
00:38:51| Disconnected… Unplug the phone
00:41:18|
00:41:18| Attempting to open the interface…
00:41:18|
00:41:18| TURN OFF PHONE!
00:41:18| Hold ‘C’ button on phone and connect phone NOW.
00:41:18| You have 30 seconds…
00:41:18|
00:41:25| Disconnected… Unplug the phone
00:41:50|
00:41:50| Attempting to open the interface…
00:41:50|
00:41:50| TURN OFF PHONE!
00:41:50| Hold ‘C’ button on phone and connect phone NOW.
00:41:50| You have 30 seconds…
00:41:50|
00:42:20| Error: Cannot open phone communication port
00:42:22| Disconnected… Unplug the phone
00:42:24|
00:42:24| Attempting to open the interface…
00:42:24|
00:42:24| TURN OFF PHONE!
00:42:24| Hold ‘C’ button on phone and connect phone NOW.
00:42:24| You have 30 seconds…
00:42:24|
00:42:30| Disconnected… Unplug the phone
00:42:34|
00:42:34| Attempting to open the interface…
00:42:34|
00:42:34| TURN OFF PHONE!
00:42:34| Hold ‘C’ button on phone and connect phone NOW.
00:42:34| You have 30 seconds…
00:42:34|
00:43:04| Error: Cannot open phone communication port
00:43:06| Disconnected… Unplug the phone
00:43:36| Shutting down…
01:08:35| XS++ v3.1 (Darwin) Ready !
01:08:35| Executed on Microsoft Windows Vista
01:08:45|
01:08:45| Attempting to open the interface…
01:08:45|
01:08:45| TURN OFF PHONE!
01:08:45| Hold ‘C’ button on phone and connect phone NOW.
01:08:45| You have 30 seconds…
01:08:45|
01:08:53| Disconnected… Unplug the phone
01:08:54|
01:08:54| Attempting to open the interface…
01:08:54|
01:08:54| TURN OFF PHONE!
01:08:54| Hold ‘C’ button on phone and connect phone NOW.
01:08:54| You have 30 seconds…
01:08:54|
01:09:08| Sorry, your phone is NOT SUPPORTED
01:09:08| Sendinging shutdown signal to phone…
01:09:10| Shutting down…
06:50:55| XS++ v3.1 (Darwin) Ready !
06:50:55| Executed on Microsoft Windows Vista
Kristoffer
god!
hard to reviwe it back
well try setool for red light blonking repair
if it works then good
else…post here what happens
Hello, my v630 is dead and redlight blinking. Note that I can’t even charge it or connect it to the PC.
I follow your guide exactly, but it’s not woking. When I plug in the device, holding 2 and 5 down, the LED blinks again and SEtool2 doesn’t seem to identify it. Is there anything else I could do?
imran
install the usb drivers then give a try back!
hey i have a 580 and its dead i did the 2+5 thing but it just recognizes the usb drive and nothing more happens :s
metal roses
u are having red light blinking??
install drivers
and try back again!!!
i have a question.. i have a w610 CID52 and it have the strange thing that if the charge is between 100% and 95% the phone works right away with out problems..but if the battery get down of the 95% the red blinking start..
how can i fix this and when can i fix this???,
i already tried when its 100% with C and Unlock/Repair and nothing fix also when its 94% with 2+5 Unlock/Repair and nothing fix..
i need help my w580i blinks red when battery is inserted was does that mean and how do i fix it
i mean my w850i
actually it is my w580i i need help when battery is inserted light blinks red 6 times nad stopsd phone wont turn on i got a fully charged battery in it i need help
i was trying to take GDFS backup of w810i. i got this error
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
Will backup GDFS now.
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35462301797570 CERT:RED
PATCH:061204 1529 HAN_DB2010_MEM_PATCHER_R2A007_CXC9876543210 0
LDR:060718 0842 LIE_DB2010_FLASHLOADER_R2A003_CXC1326738
Flash ID check:2019
Flash props sent ok
DETACH CABLE FROM PHONE.
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS “READY”
Trying to launch embedded bootloader…
INT LDR:COMPACT_ID_LOADER_CRIPPLED_SETOOL2_R2
Flash ID check:2019
Flash props sent ok
FOUND: R4EA031_CXC1250316_GENERIC_HN
Restore from:R4EA031_CXC1250316_GENERIC_HN
can’t open file “C:\Documents and Settings\Raj\Desktop\Sony\SeTool_2_Lite_v1.11\setool2lite_1.11\rest\R4EA031_CXC1250316_GENERIC_HN”
CSloader version:
SETOOL2 LITE COMPACT_SEMC_FS_LOADER (FAT V26)
loader startup: executed
wrong response, break.
failed, that is fatal
Elapsed:225 secs.
now phone doesnt power on. plz help
hi
akshayya
my phone is starting but it is stopping in that loading what shall i do i dont have even gdfs backup my erom is dead
Zander, this is the fix, if it does not work, the Sony Ericsson Service Center is your only way.
can anybody help me, i have a W880i, i have installed the flash driver using a SE W850, however becuz my w880 is dead(i get a red light behind the c button when charging) my windows vista is sayin that the usb device is not recognized so setool2 isnt piking anything up! any help would be appreciated.
Aaron, sorry what’s up ?
use some other phone to install usb drivers then attempt repair. 🙂
Hi,
I just wanted to say thanks for this post! You helped me to get my w580i to turn on again, after being told by the phone repair shop that it couldn’t be fixed i decided to try it myself. SO thank you so much for this post it was a great help!
Thanks again!
Michelle
nice
congrats!
So just to be clear, I have a W580i with the red light blinking, battery is charged. When I attempt to fix it with SEToolLite I get
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
The phone is out of warranty.
So there is nothing I can do to fix this myself?
Greg
sorry man
no way!
how come there isit any response from the SEtoollite v.1.08 when i hold Cancel or “2+5” when i on the phone…do i have to hold the buttons thru out the process?….and what’s the use of installing the drivers?…
feng
dude!
drivers let ur flash mem run!
and which phone u own?
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader…
embedded flashloader not responds !
Abort all operations.
Elapsed:65 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35224102855632 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
only FLASH operation supported in that mode
Now what happens? it still wont turn on 🙁
Btw its the w580i red light blinking 🙁
Now shows:
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35224102855632 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Hi all,
I have a W595 (DB3150) that is effectively dead.
I can connect using 2+5, and have tried flashing using A2 Uploader & DaVinci, but it always fails.
I am guessing that the EROM is corrupt so I need to repair it.
does anyone know of a way to do this; other than using D-Ultimate Unlocker for €28???
Any help would be very much appreciated.
Antony
is red light still blinking?
if it has stopped then restore gdfs
ed_case7
here we talk only about free flashing
so….no davinci or other money services…
and no way out in case of a2 uploading
and till now we didnt saw any dead problems in a2 phones!!!!
there is soemthing else wrong….
get it to ss
THAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAANKSSSS…..
THAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAANKSSSS…………………………………………………………
JUHHUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUJUJUHUHUHUHUHU
Help Me
SE Tool Doesnt pick Up My Phone But The Red Light Doesnt Blink
What Should I Do?
m.dot
which phone?
connect it back with drivers preinstalled
K550i@W610i
I Re-installed the flash driver on my computer and clicked 2+5 to connect it to se tool lite and i got this message:
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35665701686088 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:7 secs.
^ Is it Still Fixable?
Anyways People, i think my phones completely dead, so i give up, if my phones still fixable, just post it and i may think again
m.dot
gdfs is corrupt i guess
tried reflashing???
m.dot
no!!!!
first give all efforts here!
most probably it will get fixed!
if red light is no more blinking then reflahs
i’d seen this error many times and got solved from here
no ack during gdfs_readvar !
Can’t read SCRC unit
can this be fixed..?? is it any hardware problem..?
Aswin
like i said
post whole log!
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35273302016746 CERT:RED
FLASH CID:52 COLOR:RED
Model:W610i
Brand:Sony Ericsson
MAPP CXC article: R6BC002 prgCXC1250669_GENERIC_LI
MAPP CXC version: R6BC002
Language Package:CENT_EUROPE
CDA article: CDA102568/207
CDA version: R2A
Default article: cxc1250755
Default version: R6BC002
Network LOCKED
Operator: 234-33
Elapsed:118 secs.
Elapsed:118 secs.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35273302016746 CERT:RED
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:42 secs.
what happened to my phone. its still wont turn on
Bengal07
tell us the symptoms also
this is my log
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35923501808552 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:106 secs.
Elapsed:106 secs.
jammy
dude mention the problem also
is that wsod?
red light blinking anymore?
Hi, does anyone know how to fix a white screen on a z310i. Possible erom problem? How to fix erom on a Pnx3250 please thankyou
Andrew
u can try hdflasher to re flash nothing else
ya seus too!
does this erase all the phone contents e.g. contacts pictues messages??
please get back 2 me ASAP
Tanvir
no
if u didn reflashed
thanx very much!
Hi, i have sony ericsson w850i and i have the same problem the red light blinks on the power button – i download the drivers also i download the SETool Elite but when i hold the “C” button nothing happens the phone doesnt get connected what should i do ? pleasy ill wait for the answer, thanx to all.
HELP w580i dead
but i didnt install drivers b4
where can i find the flash drivers for my phone and how do i nstall them
help
Ideal Hoxha
conncet ur phone holidng 2+5
follow the given tutorial mate
edgar
in our filebase
gordons gate flash drivers
or install seus
bhuvan
my phone connects however i get:
cs(something) cant read gdfs
failed: this is fatal
edgar
tried reflashing???
try seus
right click on the log and copy it
then paste it over here
So I am having the red light flashing problem too. I have 580i. I installed all the drivers using the auto install. I opened SE Lite and hit unlock/repair. Then i pulled battery out and put it back in, held down 2 + 5 and connected usb cord to my phone…and this is what I got
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35256002628715 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:11 secs.
Dan
damn!
no way for u
cid:53
is not supported by setool!
take it to service center
im sorry but my phone doesnt even turns on and the computer doesnt detect the phone even that i hold “c” or “2+5” than how can i instal the USB Drivers i dont understand ? cuz the computer doesnt detect my phone :S i have w850i and i cant find any one alse that has the same one :S is there any solution ?
Ideal Hoxha
install gordons gate driver!
exe file
connect it back
see ports of mobile are clean
try twisting cable
i have a z310 will it work?
i installed gordon gate but it still wont recognize it.
Couple of questions with this tutorial:
1) My battery was nearly fully charged when this problem happened. Does that rule out a battery problem? Or should I still try to a new battery before flashing?
2) If I use the automatic driver install will I still need some one else’s se phone to complete the driver installation?
Lothian110
1)no this may also take place without any cause[happened with me]
2)its executable file
direct package installation
no other phone required
zac nichols
no
ur phone is pnx5230
no support in setool
only jdflasher supports it in case of flashing only
red light problem cant be solved
does Setool2lite V1.11.rar only open on certain computers????????
bobby
no
made for every windows pc
hi
i am using k810i; I had connected and installed usb drivers.but i am not update EROM.
how can i do this.
Plz help me….
Ravi.A
what are u facing?
i am not getting u
Thanks a bunch Akshay, worked like a charm!
Hi I had k810i ir blinking problem and updated the Erom. Then It displayed white screen, tried flashing in SE tool, its getting hanged while flashing the blocks.
help me pls
Anand
flash using jdflasher
its much powerful
Dude,my k800i appear a white screen
what should i do now ??
please help me SOS!!
Amy
reflash
580i w flashing red light. Downloaded drivers, connected to SETool and the program gave me “CSloader refused to start GDFS services,error is:29” Now the red light is not flashing anymore and I cannot reconnect to SEtool. Any ideas?
Jeremy
reflash
Hello Bhuvan
Phone: SE w580i
I had the same dead erom problem before. But i successfully solved it at that time and phone worked fine for a while. Now again my phone is dead & flashes red light. I tried to follow the same above steps but i got this log saying “can’t build loader’s chain” .
PS. I have uploaded w580i software from SE Update service 3 days ago. Can it be problem?
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100381747 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:9 secs.
Help is appreciated
Rahul
its no more getting repaired because u must have got ur phone updated from ss or urself using seus
cid:53
no support in setool for it
so
sorry
no way out
service centre is way out
Hey i have a problem with my sony Ericsson Few months ago it’s went dead i would press the powers button and a red light would blink later on when i went to the repair center of Sony Ericsson they said its GDFS has crashed and said it would take anywhere to 6- 8 thousand buck now for a cell phone which costs !0 thousand buck and put in another 8 thousand wasnt an option for me cuz my parent aint sum Ratan Tata’s relatives so i want to knw is it possible to repair my cellphone on my own wis Setoolkit. if i can i’ll owe you guys a favour and when geta job i’ll try to pay you guys If possible please reply
P.S its a W580i please reply back that cellphone is more dear to me than my Gfs
Rad Paul
lol
u are funny man!
cross fingers
this procedure will solve ur problem if ur phone’s erom version is not cid:53
follow whats given here
post back
😉
Having problems with W850i. EROM has crashed supposedly form what you said. The damn program doesn’t do shit. I have a lot of things on this phone that I want, and I love it. Please help.
CaptainBaconMan
if its cid53 then no way out!
how do i knw if its a cid53 ?
Rad Paul
connect to xs++
post the log here
or look out for
erom:cid__
is there any way to do this kind of method for z750i?
ayaka
z750
is a2 phone
there are no red light blinking problems reported yet in a2 phones!
tried other battery?
I have a problem, I was flashing my w580, the lights went out and now My cellphone don’t turn on again and don’t get reconized by the computer. I REALY NEED to know how to solve this! Please!
McDaniel
u mean the red light is blinking now??
try the given way out
the only way!
if ur phone is cid53 then no way for red light blinking
if its white screen
then reflash
i am a noob and facing same prob:
i am almost scared to ask but what is and how to “connect to xs++”
I have w580i : dead with blinking “c” !
And oh also in the posting you said “borrow friend’s sony fon. “my friends dont have it. What now? what next !
HELP HELP.
Dee Cee
for redlight thing u have to use setool not xs++
do the way it is given
what else?
OMG! I think I am screwed:
I did what’s given. This is the message I got… and I sense its not good news.
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100086576 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:15 secs.
HELP ! Plz.
Looks like you are enjoying ur long wknd too !!
I read a few (lot for a chick) stuff about it. I have no backups watsoever. Should I flash using main+fs+custpack or simply fs?
reply plz !
Dee Cee
is red light still blinking?
Dee Cee
yea
was off for weekend
sorry man!
if red light is no more blinking then reflash both
main & and fs including cda pack
It is still blinking !
Dee Cee
damn!
that means it must not be getting connected by ‘c’ key to any application!
are u sure battery is charged/
try other battery
or jump onto our support forum
discuss there
Hello,
I too am having te EROM error in my SE 580i AT&T USA phone, as Dee Cee. I ran SEtool 1.10 because everywhere that I searched for Version1.11 it said virus and would not install. But i get the exact same problem as Dee Cee… Except I use the kes 2 and 5 instead of C since C is not being recognized in SE Tools.
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35256002951764 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs.
I am now going to to try recharging the battery in another persons phone that is also a W580i from AT&T.
Any help would be appreciated.
Hi, i got the same problem for my S500i will this procedure work for it? I don’t want to do anything that’s irreversible… thx
Model: S500i was using it till battery died. Then tried charging it through Car charger, USB, and wall charger for a while now. Nothing seems to work… hELP!!
My k800i dead….. red blink when stat, hp cannot detect to PC… I also use this method, but still cannot detect… any suggestion?
310ccrob
yea follow the given procedure
Karn W.
is the red light still blinking?
amir
whats happening when u connect to pc now?
what happened when u tried this way?
i heard the se2tool is a trojan, should i just dl the newer version 2.1 was it? Arite heres my situation.
Swap batteries with a S500i that works and charged it. going to install the usb drivers right now onto my comp. The Phone that needs the flash though wont turn on when i put the fully charged battery… how can i flash it if it doesn’t turn on ??? gahh i suck at following directions lol. help
installed the usb flash drives shouldve worked but couldnt find the ggsemc.inf file to install… so i went and did the setool thing anyway… got this msg after loading setool lite
drop menu chose my s500 then clicked unlock/repair then put battery in then held 2+5 and connected usb and got this msg.
chipid; 9900, emp protocol:0301
bootrom mode detected
Flash props sent ok
loader startup: executed
CSloader refused to start GDFS services, error is: 29 failed, that is fatal
elapsed: 5 secs.
Yes the red light is still flashing. I Windows XP Service Pack 3, with SE Tool Lite 1.10 running.
anyone ever used SEtool for a k610i or does it work for a wide range
Karn W.
u have the old gdfs backup?
if nothing then jump to our support forum
joel
will work with ur k610
😉
Hey Bhuvan the GDFS backup that I have is from XS++ 3.1 Tool. Although I cannot get my phone to connect to it. And I do not know if that backup can be used in SETool2 v1.10. Also I do not have a bacup of the GDFS with SETool2.
ive had this problem for a while now…
Karn W.
that backup can only be used with the xs++ with which it was made!
Phone Sighz
yea
the lught blinks only for 5 seconds!
check the battery
if nothing helps then do whats given here
hi
i have a se k610 and its blinking red light when charging.the phone is dead and won’t switch on so I took out the battery to see if it works, and tested it in another mobile, it did not work. I took the second mobile phone battery and tested it on my did not work either.
PLEESE HELP ME thanks
any updates on CID53 EROM repair , red blinking light.
SWUS updated my w580i to CID53. How much does service centers in India (mumbai) charge for these issues.
yussuf
the given guide is the solution for u
abhay
sorry man
cid53 erom can be repaired for free yet!
Thanks for replying Bhuvan,
Can I get it done locally (mumbai) . the service centers charge tooo much. I bought display for w580i for 550 Rs (99%) was asked to pay 2300 Rs by the service center.
abhay
yea service center sucks!
they may ask u to get a new motherboard which may cost approx 3.5k!!!!
so make a new thread at forum
and ask for online paid support!
there are online genuine solutions!
bhuvan says
amir
whats happening when u connect to pc now?
what happened when u tried this way?
– Pc not detect the phone. i’m waiting more than 60sec with the thumb on 2+5. After that i press STOP to stop the scanning, it then say; ‘pre-boot failed… recovery needed.’
The others forum say that swap +ve & -ve supply battery to phone also works, is it true?
At last…. the problem solved.. the dead now alive.. pc cannot detect because the phone dirty at bottom (for cable connection).. i just open phone, clean the 12 gold and try this method.. Hole in One!!! 1st try after service and succes in only 22sec.. after let it dead near a month.. ten-QQQQQQQQQQQQQQQQQQQ alot….
amir
i appreciate the way u replied!
cuz we usually forget if people do not revert in a day cuz we have to deal with a lot of stuff a day!
anyways
yea this is universal se problem!
keep the port clean!
anyways
goodluck
😉
good to have ur phone working fine back
hey bhuvan , you told me about online repair solution for CID53 erom repair, I could not find anything except for wotanserver. Are there any other sites. Also PLEASE let me know can it done any where in mumbai.
You were right SE service Center told its a mother board issue and asked me to pay 4.5K !
abhay
ss sucks!
search for se box
or setool full
or ask at our forum
i tried all that but when it comes to doing the repair part it wont detect my phone when i try connecting C or 2+5, in the end i jus unplug it it just says ” Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:95 secs.”
Where can I download SeTool 2?
Have a Z310a with a flashing light on the infared connector on the side of the phone.
Put it on charger last night and woke up this morning with the flashing light. I have 3 of these phones. Took battery out of working phone with no effect. Tried to connect and upgrade software with usb cable and software upgrade from sony with no effect . Computer will not find phone or eprom. Try manual and automatic flasher and computer will not find phone. Help
Makhosi
man this is pretty jumbled up!
discuss at our forum
cant be sorted out by one shot
expositive
download from the link we have provided or from filebase
Tony
installed usb flash driver??
follow this guide only
it can only help u!
Did all you asked. did flash driver (which by the way is also included with the sony upgrade software). Tried the SEtool2 lite and it doesn’t have the Z310a eprom software.
tried everything you have written for 17 pages with no luck…
my p1i is not starting after interrupted software update, the seus does not identifies my phone now, only keypads and screen(very dim) lights up and goes off after few sec and why i connect it for charging red light blinks for a sec and goes off and again after few sec keypads and screen(very dim) lights up and goes off.what should i do and how can i know that my battery is charged or not??
prasoon
in actual erom dead reports we never saw a case like this!
only red light is supposed to blink.
i guess its some hardware problem.
you may discuss it at our forum for more.
Hello, w850i w red light here. My battery gets hot after minutes of installing it. Tried other w300i baterry, the same thing.
I run the gordon gates thing, says reset ports ok.
Then I run Se tool lite v1.11
select w850 from the list, then press repair button.
Put the battery in, press 2+5, plug into USB, hold for over a minute o two, and the
green bar on the bottom never fully fills, it returns after almost finishing and starts again, and no info about the phone :(. What can I do?? Help..please…
Casper
this is strange
try discussing it at our support forum!
Ohh, and the red light on mine is on all the time, not blinking or anything. Just red. Anyone who can repair it for me?? I pay!
OMG, my K800i dead, red blinking when turn on.
this is what happen after try unlock/repair method.
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35xxxxxxxxxxxx CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:101 secs.
Elapsed:101 secs.
Please help….
Casper
try other battery
we provide here everything for free
Naja
now is ur phone getting connected by pressing ‘c’ key???
or u have the gdfs backup?
hiee..my pc doesnt detect my w580i after i have installed usb flash drivers with my friends phone.i waited for 60 secs.and unplugged it .it says.Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:95 secs.” CAN ANY ONE PLEASE TELL ME HOW TO MAKE MY 580I TO FLASH..ITS DEAD NOW….
harsha
retry man!
its problem with usb connection!
twist the cable a bit, clean the port of ur phone!
also dont forget to install drivers!
Why is not W705u supported in SeToolLite?
Cuz its dead! 🙁 Must get it to work somehow…
Padde
ur phone is a2!
use a2 uploader!
Hello Bhuvan
I followed the instructions but I get the error “embedded flashloader not responds !”
Any suggestions?
Thanks!
Natasha
is redlight still blinking??
it would be better if u post whole log here!
Hi Bhuvan
I tried to unlock my C902 with Aerix which seemed to be successful but then my phone now won’t turn on. I’ve tried SEToolLite but it doesn’t have an option for this model of SE. Any ideas.
Thanks
Sam
Sam
like i asked u at blog too…did u completed aerix task successfully?
try reflashing through a2 uploader!
get generic firmwares from topsony.com
I tried fixing my w580i and this is what i got,
Note: on the phone type i used w580 because i couldnt find w580i.
My problem is that my phone turned off and it wouldnt come back on and when i try to turn it on it would blink in red
welcome to setool2 lite edition v 1.07
supported DB2010/DB2012 CID49/50/51, DB2020 CID49/51/52
Loaded 51 flash descriptors
ChipID:9900,EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35256002774947 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:10 secs.
I still cant turn it on what should I try next,
I tried flashing it using W580_R6BC002_FS_AMERICA_1_RED52.fbn
and this is what i got
welcome to setool2 lite edition v 1.07
supported DB2010/DB2012 CID49/50/51, DB2020 CID49/51/52
Loaded 51 flash descriptors
ChipID:9900,EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35256002774947 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
writing C:\Users\Alsadeq\Desktop\W580_R6BC002_FS_AMERICA_1_RED52.fbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:4180
Will flash 209 blocks…
ldr blk write fail. fatal
Abort all operations.
Can’t get packet properties.
verify block error
last blk:46780000,00010000
Elapsed:141 secs.
hi my sony erricson only flashes red light ……i used it on night and when i woke up in the morning it doesnot work can you plz help me i m in need i show my phone to customer care they said your gdfs file is corrupt and they are demanding rs1000 says that this file has to be bought from net plz help if u can i m in great need .plz mail me if possible [email protected]
Haytham, try reflashing FS via 2+5
other wise sorry try some paid tool, this is now all too old.
hi,
my w610i has this red light blinking problem and cant turn on too. tried your method but got the following log. can you kindly advise on how to proceed further.
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35489401458769 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:90 secs.
Elapsed:90 secs.
hi erni here. would also like to add, the red light is still blinking after doing this. what else will you need to know?
well its all done
good post
Im so angry, i dont know waht to do. My Phones completely OFF! & there is a flashing red light on the side. Its a k800i. WHAT DOES THIS MEAN. WHAT DO I DOOOO?
where can i find SE Tool 2 Lite 1.11
please email me back, i have a s500i and it blinks and nothing come on
[email protected]
has cid53 dead phone’s issue beend fixed?
hey, akshayy…i m in deep trouble man.. my w910 suddenly turns off and not responding..when turn on, red light blinks & left soft key flashes red three times…. i followed ur erom repair step…but there is some error..
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:C802,EMP protocol:0401
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
skipping empty loader…
Can’t load ID loader !
Elapsed:5 secs.
but with a2 uploader it takes flash perfectly…even i can access fs through that..but…it neither turns on. i chcked my battery & charged fully but nothing happened, same problem..red light blinks & left soft key flashes red three times 🙁 what can i do man. give me sum suggesitions man…
i have a satio u1i and i have this problem, i have no 2 and 5 keys to hold tho lol
anyone able to help??
remeber..it me Lazar_Enrike help me please.
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463901217291 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader filesystem startup: executed
loader GDFS startup: executed
Will execute script now.
Writing GDFS var 0001:084E len:015B
Success
Phone detached
Elapsed:65 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463901217291 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:88 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463901217291 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader filesystem startup: executed
loader GDFS startup: executed
Will execute script now.
Phone detached
Elapsed:86 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463901217291 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:71 secs.
ok i sent you a mail, reply.
Akshay,
Does This Apply For The ‘BROD’ On The K850i??
If Not What Shall I Do,
Ive Tried Flashin The Main And Fs Btw,
Thankss
hey akshay,
ive tried doing this with my k610i but alas it doesnt work. will my phone ever start again, because what i did was i accidently used a gdfs backup on the k610i from another phone and now its dead. =(. do you have any advice? thanks in advance.
oops sry wrong email address send to this one, or put on this page plz
hey akshay, i wonder if you can help me fix my phone. what i did is this: i accidently used a wrong gdfs backup onto my k610i and now it is absolutely dead. the setool unlock/repair no longer helps and i deleted my old gdfs backup in anger =/. the symptoms of the k610i is that the red light blinks once/5 times and wont start up or charge and when identifying on setool it says “IMEI mismatch”. i’ve tried reflashing the whole k610i but when flashing the fs firmware it stops at 32/140. i hope you can help! thanks in advance.
no, flash back actual gdfs, then flash, main, fs. try some other firmweare versions
Hey Guys i am back ok now like i told before my cellphone Sony Ericsson W580i is showing me a read light when i try to switch it on from my past research i learn its a Erom problem. So how do i fix it and i donno if its Cid 53 or 52 can please tell me that its fixable
HELLO GUYZZZ..
I HAVE INSTALLED SOME NEW GAME TO MY K-790i..
THEN I CHNAGED MY SIM AND TRY TO START STILL IT,S NOT STARTING EVEN NOT FLASHING JUST SHOWING RED LIGHT BLINKING AT INFRAED PORT AND I WANT IT TO CONNECT TO MY PC BUT IT,s NOT RECOCNIZED WHT SHUD I DO?????
Rad Paul, no, sorry.
get it serviced from SE center. no other option these days.
man i gotta spend 7 thousand buck to repair a 10 thousand phone its crazy didnt you guys like help before ??? and plus i did give it to em the price was to much and i had kept the phone with em for over a week and they hadn’t repaired it then when i got my cellphone back 3 screws r missing so i dont trust em anymore
hey akshay
sony ericsson c905:
the phone had flashing red light on the side but after charging for a while it’s gone. yet, still can’t turn the phone on. :((((
is it erom problem or gdfas problem?
also is it fixable
thanks
no way to fix those new phones with such issues, service center only way.
hi Akshay.
my SE s500i just won’t turn on and flashes red light 5 times when i try to turn it on. i’ve used this phone for like two years now. it’s never happend before. the only thing i did was take turned my phone off then took the sim card out, put back my batteries back in. then when i put back my sim card, the phone just wont turn on, and flashes red light. so what can i do to help my phone? TT_TT
i have a sony ericsson v630i its a phone i ahve spare and want to sell when i try to turn it on the light flashes twice at the top of the phone the se tool light dose not work what do i do
hi, someone called me and i was using my sony ericsson w580i, and i picked up, but then it suddenly froze. i waited for a while, but it wouldnt do anything. so i took the batteries out and reinstered them. when i tried to turn it on, it just flashed red.
i tried to use setool2, but it wouldn’t detext my phone! PLEASE HELP!! D ;
now it detects my phone, but it says
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35923501793511 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs.
PLEASE HELP ) ;
Thanks very much, fixed my SE k800i with SEtool2 lit
dear akshayy,
how bout fix red blink k810.thanks
My K750 is dead when i tried to convert it to w800. How can i get it alive back. There is any way updating it with sony ericsson update service? If i do it says the phone already has latest software. But the didn’t even start, shows only white screen. Can anyone help me
19:53:17| Activating GDFS…
19:53:17| Warning: IMEI name does not match GDFS name (IMEI:K750 GDFS:????)
19:53:17| …using IMEI name
19:53:17|
19:53:17| Profiling SEMC phone…
19:53:17| Platform: DB2010
19:53:17| OTP CID: 49
19:53:17| EROM CID: 49
19:53:17| EROM Color: Red
19:53:17| IMEI: 35437701xxxxxx
19:53:17| Phone ID: K750
19:53:17| Region: ›¾vÐA
19:53:17| CDA: ›¾¢ÐA ›¾¢ÐA
19:53:17| Firmware Version: ›‰
19:53:17| EROM: n/a
19:53:17| Ready for operation!
This trick worked like a charm! Thank you so much!
can i repair damage erom with setool2lite v1.11 on my w800 cid36 brown?
my w800 was death when i try to convert from cid36 brown to cid36 red
can i use another version of setool2lite?
hey akshay my k610 has dead,,,when switching on it just blinks the light in indicator….
Using SeTool2 lite 1.11 we can fix this problem by this way.
Start SeTool 2 lite
Press Unlock\Repair Button, The first button.
Reinsert Battery
Connect phone holding 2+5
Wait, SeTool 2 lite will repair the EROM, it will flash it back.
Done
i did al this and the se tool2lite find and respond with my mobile,,,it identified but then also it didnt switch on…..what i do,,,,,,
guys, gals…. Need help bad!
my k850i is running rogers version of firmware (the latest as far as i know)
few months back had a prob where i wasnt geting txts and phone was locking up… ran repair tool in SE suite… and it fixed it… ran a update afterwards…
then yesterday
was taking a picture… phone locked up and turned off (batt was at 3/4)
thing will not turn on… have tryed making it go into boot mode holding C and also using the 2/5 function…
what I get out of it no matter what I do when its pluged in is solid red power button… not flashing like other posts ive seen….
I have tryed setool2 lite v1.11
I have tryed XS++ (serveral diff versions)
can not get it to reconize on the computer… no prompt for drivers or any recognition at all
have tryed my 7×64 and XP x86 system… tryed diff ports….
have left it charging for like 6 hours with the red light on, also try charging without it coming on for around the same time…
I have left the battery out of it and tryed plugging it in….
I have even tryed a diff battery….
I am running out of options and do belive i have a month or two till my warrenty is up (if it is 24 months like ive read) but rogers cell check is bs…
If i can avoid these crooks and just get the damn into boot mode I would be golden…
any thoughts???
should also add the camera lens is stuck open…. tryed booting with the camera function switch in diff placs too…. nothing at all……
My friend’s K800i blink red…I need only setool 2 lite 11.1 for that?right?And mine k800i is locked for vodafone,so I need only setool 2lite 11.1,right?respond pleeeease!!!thanks in advance… 🙂
hi ashkay,
i need to fix my k10i i think thats it. a red light flashes 5 times. i tried setool lite it doesnt work helppppppp
I Have sony ericsson w610i about 2 years and before one week it started stucking and i had to put of the battery and making reboot to be unstucked.I tried to update it with se update service but it stucked in the middle of the update and after that it doesn’t oppens.Only a red light blinks.I checked the battery but it is ok.So as i searhed i found out that the problem is the erom or gdfs.I am trying to repair it with flashing programms,but nothing.How i can revive it? AAny suggestions?
SCREENSHOOTS FOR HELP!
SETOOL2LITE
IDENTIFY w610i.png”>http://img202.imageshack.us/img202/1654/w610i.png
UNLOCK/REPAIR w610ii.png”>http://img686.imageshack.us/img686/3912/w610ii.png
JD FLASHER
http://img405.imageshack.us/img405/2744/jdflasher.png
OFLASH ERROR http://img143.imageshack.us/img143/7…sheroflash.png
OFS ERROR
http://img251.imageshack.us/img251/7…severerror.png
Se King
IDENTIFY
http://img5.imageshack.us/img5/8121/seking.png
XS++
IDENTIFY
http://img130.imageshack.us/img130/97/97587919.png
It appears as Z520,but it is W610i!!!
BACKUP GDFS AFTER IDENTIFY
http://img132.imageshack.us/img132/6…backupgdfs.png
FLASH AFTER IDENTIFY
http://img693.imageshack.us/img693/3…ashingmode.png
I Have sony ericsson w610i about 2 years and before one week it started stucking and i had to put of the battery and making reboot to be unstucked.I tried to update it with se update service but it stucked in the middle of the update and after that it doesn’t oppens.Only a red light blinks.I checked the battery but it is ok.So as i searhed i found out that the problem is the erom or gdfs.I am trying to repair it with flashing programms,but nothing.How i can revive it?
SCREENSHOOTS FOR HELP!
JD FLASHER
http://img405.imageshack.us/img405/2744/jdflasher.png
OFLASH ERROR
http://img143.imageshack.us/img143/7282 … oflash.png
OFS ERROR
http://img251.imageshack.us/img251/7980 … rerror.png
Se King
IDENTIFY
http://img5.imageshack.us/img5/8121/seking.png
XS++
IDENTIFY
http://img130.imageshack.us/img130/97/97587919.png
It appears as Z520,but it is W610i!!!
BACKUP GDFS AFTER IDENTIFY
http://img132.imageshack.us/img132/6471 … upgdfs.png
FLASH AFTER IDENTIFY
http://img693.imageshack.us/img693/3593 … ngmode.png
SETOOL2LITE
IDENTIFY
http://img202.imageshack.us/img202/1654/w610i.png
UNLOCK/REPAIR
http://img686.imageshack.us/img686/3912/w610ii.png
OFLASH ERROR
http://img143.imageshack.us/img143/7282/jdflasheroflash.png
OFS ERROR
http://img251.imageshack.us/img251/7980/ofsstartingfssevererror.png
BACKUP GDFS AFTER IDENTIFY
http://img132.imageshack.us/img132/6471/xsidentifybackupgdfs.png
FLASH AFTER IDENTIFY
http://img693.imageshack.us/img693/3593/xsflashingmode.png
I Have sony ericsson w610i about 2 years and before one week it started stucking and i had to put of the battery and making reboot to be unstucked.I tried to update it with se update service but it stucked in the middle of the update and after that it doesn’t oppens.Only a red light blinks.I checked the battery but it is ok.So as i searhed i found out that the problem is the erom or gdfs.I am trying to repair it with flashing programms,but nothing.How can i fix it?
SCREENSHOOTS FOR HELP!
SETOOL2LITE
IDENTIFY
http://img202.imageshack.us/img202/1654/w610i.png
UNLOCK/REPAIR http://img686.imageshack.us/img686/3912/w610ii.png
JD FLASHER
http://img405.imageshack.us/img405/2744/jdflasher.png
OFLASH ERROR
http://img143.imageshack.us/img143/7282/jdflasheroflash.png
OFS ERROR
http://img251.imageshack.us/img251/7980/ofsstartingfssevererror.png
Se King
IDENTIFY
http://img5.imageshack.us/img5/8121/seking.png
XS++
IDENTIFY
http://img130.imageshack.us/img130/97/97587919.png
It appears as Z520,but it is W610i!!!
BACKUP GDFS AFTER IDENTIFY
http://img132.imageshack.us/img132/6471/xsidentifybackupgdfs.png
FLASH AFTER IDENTIFY
http://img693.imageshack.us/img693/3593/xsflashingmode.png
OMNIUS
IDENTIFICATION
http://img716.imageshack.us/img716/7045/omnius.png
TRY TO BACKUP THE GDFS
http://img37.imageshack.us/img37/7656/backupd.png
RESTORE GDFS FAILED!
http://img36.imageshack.us/img36/3094/restoregdfs.png
My phone is doing the flashing thing but i’ve noo clue what I have to do. All that sounds like chinese to me ! I’m downloadin the setool lite 2 thing but it’s a zip file and i don’t even know how to unzip it. i’m useless. please help
hey akshaya dis is kiran i am stuck wid ma w580i phone ……………i was applying vkp patches nd i did it sucessfully …after switching on ma phone suddenly it gone stucked nd a red light is blinking…..how can i fix it up………..my phone is cid53 w580i….waiting 4r ur reply thaks………..
heylo……any ones der to help me out……………………….
hey akshaya dis is kiran i am stuck wid ma w580i phone ……………i was applying vkp patches nd i did it sucessfully …after switching on ma phone suddenly it gone stucked nd a red light is blinking…..how can i fix it up………..my phone is cid53 w580i….waiting 4r ur reply thaks………..i`m waiting for some one to help me out
hey akshaya dis is kiran i am stuck wid ma w580i phone ……………i was applying vkp patches nd i did it sucessfully …after switching on ma phone suddenly it gone stucked nd a red light is blinking…..how can i fix it up………..my phone is cid53 w580i….waiting 4r ur reply thaks………..i`m waiting for some one to help me out………..
hey floks…….sup der is software which repares erom cid 53 phone………………dead erom………nd even it changes ur phone cid`s from cid 53 to cid 52 or cid49brown……………………….omnius_se is d software which changes every thin……………………………sorry 4r my bad english?????????????
hy i have a k750i phone and i can’t tun it on , and its showing me a solid read light
what can i do ? please help
Hi akshay.
Wil the 2+5 method work for my k550@w610.
I was out of touch wid d site nd my phns dead since 6 months…
@anmol
yeah that will, if ur phone is cid52
@ken, follow this guide
kiran
ur phone’s erom is dead now!
but you are lucky, few days back there was no cid53 repair!!!
now its possible
new guide is on way, just wait
i hav w910i,,,i got the same prob of red blinking.I tried u r procedure but anable to recover..
SE tool is showing something like this
BOOTROM MODE DETECETED
skipping empty loader…
can’t load ID loader !
PLEASE help me out
in ur tutorial on how to repair a fone wid dead erom u said i had to
install drivers…
how do i do that coz my phones nt working and i dont hav a w610 with
anyone in our college..
shud i install with a differnt phone…
i connected it using 2+5 and a notification came up saying new
hardware found bt didnt detect the drivers….
help!!!
anmol
k550@w610i
anmol
download gordon gate drivers from filebase
hey i have a similar problem with my g700 when i hold down the on button it vibrates but then nothing hapens, also in settool2 there was no option to pick g700 so i was wondering if this is the right way to revive it
thnx
bob
vibrating??
then right light must not blinking, reflash!!!!
if red light is blinking check our latest guide for erom repair, ur phone is spurted! 🙂
welcome to setool2 lite edition v 1.08
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:44 secs.
ChipID:9900,EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
err: 45 (13)
loader prologue returns invalid status
phone pre-boot failed,possible RECOVERY needed.
Elapsed:7 secs.
:-c
:-(:-(:-(:-(:-(
my sony ericsson satio has been blocked by orange, is there anything I can do to unblock it, thanks.
derek
yeah
unlock it using omnius!
guide will be here i couple of days!
🙂
I downloaded the SeTool 1.11 and it doesn’t have w595 on it what do i do…
sadsd
your phone is based on new platform! if red light is blinking then look at new guide for repairing dead erom using omnius!
😉
hi, i just did this with my w580i and said its done but still get the red flashing light, any ideas why ?
hi i hav the same problem
[IMG]http://i1009.photobucket.com/albums/af216/sandeeprdy/sony%20ericsson/sonyericssonfi.png[/IMG]
now my phone is cid 53
i think it has been long time since this thread started, is my phone now supported?
phone sony ericsson k810i
jkd
post the log
sandeeprdy
congrats u have solution!!!
look at newest guide for erom downgrade/repair
that will bring u to cid52
then u can attempt a repair!
i write gdfs w580 to s500 🙁 my phon is dead.//////////// helpppppp
Welcome to SEtool2 ( LITE edition ) v 1.10
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
Abort all operations.
Can’t load ID loader !
Elapsed:2 secs.
Elapsed:2 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35297202456747 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:79 secs.
RECOVERY MODE STARTED
BOOTROM MODE DETECTED
skipping empty loader…
All possible recovery loaders fail. That phone not supported
Elapsed:27 secs.
RECOVERY MODE STARTED
Abort all operations.
Elapsed:14 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35297202456747 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
smth wrong with usercode reset,error is: 1
Elapsed:84 secs.
unlock and repair but my phon is off
nevada
now whats happening?
how is phone behaving?
hi, bhuwan.
it was a k510,
does it support flash menus or do i have to flash it to another?
i uploaded flash menus to it using FAR manager. but menu didn’t work.
then i used setool2lite, iconnect it using FLASH option.
but didn’t use any firmwares
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35238201734561 CERT:RED
PATCH:061204 1529 HAN_DB2010_MEM_PATCHER_R2A007_CXC9876543210 0
LDR:060718 0842 LIE_DB2010_FLASHLOADER_R2A003_CXC1326738
Flash ID check:897E
Flash props sent ok
DETACH CABLE FROM PHONE.
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS “READY”
Abort all operations.
Elapsed:578 secs.
after this when iconnect the phone it didn’t respond.
and now phone doesn’t start! no red light blinking,
but still i can connect my phone to setool2lite and FAR.
please help me!!!!
please remove my IMEI bhuwan, thankz
i culdnt find firmwares for my phone
i tried to repair using setool2lite.
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:3523820XXXXXXX CERT:RED
FLASH CID:49 COLOR:RED
Model:K510i
MAPP CXC article: R4CH003 prgCXC1250232_CHINA_CO
MAPP CXC version: R4CH003
Language Package:APAC
CDA article: CDA102459/101
CDA version: R3A
Default article: cxc1250246
Default version: R4CH003
Operator: 000-00
USERCODE:3590
RESTORATION FILE PRESENT FOR DETECTED FIRMWARE
Elapsed:6 secs.
Elapsed:6 secs.
what does this mean??
do i have to use any file to restore??
now my phone is dead:-(((((((((((((((
may i reflash all the firmwares???
krish
dude wht r u trying to do?
flash menus then reflashing???
tell me first if the phone working perfect??
yes then to get flash menus to work crossflash r phone to w200i, download firmwares from topsony.com
use jdflasher
then flash menus will work and phone will be far better than k510
nevada
what was the very first problem ur phone was facing?
and tried reflashing??
try that first of phone is dead
i flash my backup file w580 to my s500.and my phon is dead//
bhuwan,
that k510 didn’t turn on after i copied flash menu using FAR!
then i had to reflash it! it worked!
but now these codes are not working on it???
( *#06# _IMEI and * > * < < * _cus menu )
is some thing wrong??
i didn't cross flash it since it is my friend's phone.
he got afraid to do so!
🙂 any way
3 of you are doing great…. go on!
krish
if u crossflashed it, then yea it has to change, dont worry, will not cause any trouble! 🙂
but u say that u did not then its strange!!!! n yea like i said k510 do not support flash menus, try w200 firmware! best
thanks for the valuable comment anyways! 🙂
nevada
reflash ur w580 with w580 firmware only
bhuwan
i didn’t crossflash it. but when i enter those codes,it returns to stand by screeen.
if i cross flash it, bluetooth will not work, right? 🙂
my phone is k770i cid 53 it’s flash lite 1.1 right?
can i upgrade my flashlite version? or is there any other way to use flashlite 2 files in my phone?
i got awsome menus,all are flashlite ver 2
another thing. can i change my media player to walkmon.
sorry for many questions!!! 🙂
krish
yea u have a lot of queries!!! here we respond to things related to guides!!! u are advanced now, so jump to our forum! ask as much as u want!
all the above queries will be solved at once! 😉
what is the sign if you the setool successfully repair the erom?could someone answer this please..my phone is dead and no signs of red blinking or whatever..please i need you help
rayven
try a reflash
and post the setool log here, at the end it should signify success
@bhuvan thanks 4r d reply man ………………………….ma phone works fine now…i made it alright by usin ominus_se…………….
kiran
😉
cool
a disaster!!! :O
‘m using a SE G502
initially bus (tow) ran over my mobile. . but my mobile survived (dont ask me how) but the screen was all cracked up. . n i got it replaced for 2K and thn it got drenched in rain. . and thn it started showing red light near the camera. . i again took tht to the service center and got it fixed . . n it worked for few days n the same thing happened. . n i jut left my mobile in a corner. . . .
but thn decided to look online to fix it and bumped into this AMAZING tutorial. . . initially it worked!! by fluke. . but thn today i kept my mobile for charging and whn i came back the screen was blank ant the red light was back again. . . but the weird thing is whn i try updating the firmware thru SE update service . . it detects the mobile and sez tht the firmware is up to date. . . but thn i updated it again ignoring the data in the mobile coz i had a back up. .
but thn if i connect it to SE tools using 2+5 its not identifying/repairing/flashing. .
and this is wht i get whn i try to identify it. .
Can’t load ID loader !
Elapsed:41 secs.
Abort all operations.
whn repaired. .
Can’t load ID loader !
Elapsed:26 secs.
Elapsed:27 secs.
Abort all operations.
whn flashed. . . .
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:23 secs.
pls tell me wht to do!!!! ?? 😐
hi there. i had problem with my phone.
i tried to reflash it but i don’t where i went wrong.
could you please guys explain this to me.
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
FILE RECOGNIZED AS CUSTOMIZATION PACKAGE.
CDA:CDA102568/7
MODEL:HB1-06 Gen
VARIANT:C_ASIA
LANGUAGE: EN
LANGUAGE: AR
LANGUAGE: RU
LANGUAGE: TR
LANGUAGE: UK
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35283701143363 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CID52 BYPASS PROCEDURE STARTED
Processing part1…
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2…
Processing part3….
OTP LOCKED:1 CID:51 PAF:1 IMEI:35283701143363 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
verify block error
last blk:44990000,00010000
CID52 BYPASS PROCEDURE FINISHED
Elapsed:237 secs.
Hey, wonderful post, great job!
My phone is dead so i want to ask,
1. Does Flashing firmwares cause phone to be dead?
2. I was changing my SIM card, and after switching it on, as usual our phone asks configuration set up and denied it and then suddenly my phone got switched off. Switching it on again shows RED LED blinking for 4-5 times. Does it s/w problem or my phone is dead?
3. I’ve recently visited SE service center, my phone is with them with some advance money and they called me up and told your phone is dead and for repair you ll have to pay 3,500 Rs. Are they right or just bluffing customers?
My friend told me that now if you tell them that I don’t want to get it repaired and give me my dead phone back then they will deliberately make some changes with ur phone and shows you faulty. Is this something like that? Please people help me, I would be grateful to you! 🙂
help someone,i try but this pops up
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01157200999266 CERT:N/A
FLASH CID:52 COLOR:RED
ldr_on_ldr hdr no ack (10)
Elapsed:11 secs.
i had a same problem with my cell phone . and saw many soultions here but none of them work and my cell is not detect by the computer when i plug it wid data cable. and even shop repair man also tried alot . no sign shows. anyone knws any idea abt it?
hi, I just turned off my S500, then i removed the SIM Card, and put another in it. And when I wanted to start my phone again, BUMP, it was dead with the red blink, I’ve tried the SETool but it didnt even show any info, i’ve tried both ways (‘c button’, ‘2+5’) but SETool doesn’t seem to detect any sign of life on my phone!, what can I do?
pls help me.. my SE w880i wont start. but it blinks red light when i turned it on. i tried xs++ and selite but it wont detect my phone. im sure ive got drivers because i just installed SE PC suite.. pls help me and my phone.
hi akshay.. can i ask you tutorial how to put other language on sony ericsson here?
im new in modding sony ericsson,
sorry for my bad english
Hi, I have the w580i, and after unlockedd I pressed the executor game and it wouldn’t function. Trying to reflash gives me this error:
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:53
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35923501340983 CERT:RED
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:8 secs.
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:18 secs.
Please help! 🙁
Hello Akshayy, First of all i would like to thank you brother for all ur effort
now please solve this problem with my SE W580i(flashed S500i)
I was browsing internet and was listening to songs simultaneously. My phone got heated up excessively, got hanged for a couple of minutes and then it got switched off automatically.
after 5 minutes i tried starting it and a red light started blinking at the right side of the phone after every attempt of starting the phone.
I tried flashing the EROM with the procedure you mentioned above but i got the error mentioned below.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35923501618448 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:8 secs
I also tried reflashing my phone using XS++ but it didn’t even detect my phone
Is there anyway of recovering my phone????
Plz help
Se c903 flex is damaged. then replaced it. again damaged and when i tried to repair red light is always on. is this a sign of that the mobile is completely dead? i tried all of above. nothing worked for me. no phone is detected with ‘C’ or ‘2+5’. help me plz
dont kno if this thread or board is still active, but i was still using my w580i until the red light blinking problem appeared and now seemingly unrepairable phone, followed the original posting instructions above and here’s SEToll 1.11 results below, if any1 can help… thx..
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition – please visit http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100632237 CERT:N/A
FLASH CID:53 COLOR:RED
no ack during gdfs_readvar !
Can’t read SCRC unit
Elapsed:142 secs.
Elapsed:142 secs.
then tried again on other usb port
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:01127100632237 CERT:N/A
FLASH CID:53 COLOR:RED
Can’t build loaders chain ;(
Elapsed:49 secs.
tried again with switch in SETool to use “quik access” patch
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader…
embedded flashloader not responds !
Elapsed:46 secs.
my comment deleted again.
akshayy, why is this happening yr
i want my cell phone fixed too
Hey u guys. i just found my old w800i, and i remember the glory days, when i used it. and shit it was epic.
but… my phone is shitty dead :< , and i really dno wat to do, i hope u guys can help me a little.
so, first i tried putting the charge in, and had it lay around 30-45 mins, to see if anything happent, but i did not. well then i started trying another batteri from a t280i , not the comple same batteri, but same volt specs, so should not be a problem, but the phone does not react at all. when i put in the normal batteri, and plugs in the charger, the Red light in the top, flashes one time.
…. any one?
HI, I WANT TO DEBRAND MY 880i WHICH IS ON 3 UK (ALL LOCKS SHOWS OFPN IN SERVICE MENU) PLZ. HELP ME WHICH FILES I SHOULD USE FOR FLASHING PHONE DETAILS ARE:
17:38:02| XS++ v3.1 (Darwin) Ready !
17:38:02| Executed on Microsoft Windows XP
17:38:32|
17:38:32| Attempting to open the interface…
17:38:32|
17:38:32| TURN OFF PHONE!
17:38:32| Hold ‘C’ button on phone and connect phone NOW.
17:38:32| You have 30 seconds…
17:38:32|
17:38:37| Baseband ID: 9900
17:38:37| Protocol Version: 3.1
17:38:37| Phone name detected!
17:38:37|
17:38:37| Profiling SEMC phone…
17:38:37| Platform: DB2020
17:38:37| OTP CID: 51
17:38:37| EROM CID: 52
17:38:37| EROM Color: Red
17:38:37| IMEI: 35777401xxxxxx
17:38:37| Phone ID: W880
17:38:37| Region: HUTCH_1
17:38:37| CDA: CDA102719/3 R16A
17:38:37| Firmware Version: R1KG001
17:38:37| EROM: R3A022
17:38:37| Ready for operation!
It doesnt work for me,i have k550 pls help me! I tried almost everything,i was holding c,i was holding power up button,but nothing still done!
hey dude……….
i have sony ericcson w700i and its problem is dat whn i switch on,i can send msg after 5 hours but now im not able to send any msgs itself………….can u help me with dis Akshay?
plzzzzzzz……..
Sony ericson W200 was dead and red light blinging on the top and Omnius,SE tool2 lite cannot identify the phone
AKshay,
I have a w100 spiro, and it seems that only se-tools 2 lite 1.9 includes my phone. I have been searching for this version, but cannot seem to find it. I have been trying to use the Sony UpdateService, but it never gets past the connect phase. Can I use any other model´s firmware to bring my phone back to life? with se tools?
my sony ericsson g700 mobile is not getting started turn back to off and tnen automatically on then off like this only what can i do for this using xs++ 3.1 or 3.2
akshay SeTool2 lite 1.11says can’t load ID loder
HIi, there was a red light flashing but i din not know was it wrong soi recentky send my K810i to a phone shop. He look it and said that could be and IC issue. So i believe him and make him to do it. After getting my phone back the battery shelf life is only a day even a fresh new battery. I have no idea what has gone wrong. please help me how to fix it.. i love this phone so much…….